| Last Modified: 01-30-2024 | 6.11:8.1.0 | Doc ID: RM10000000214QG |
| Model Year Start: 2022 | Model: RAV4 | Prod Date Range: [12/2021 - ] |
| Title: BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster): C136F00; Non-learning of the Braking System information.; 2022 - 2024 MY RAV4 RAV4 HV [12/2021 - ] | ||
|
DTC |
C136F00 |
Non-learning of the Braking System information. |
DESCRIPTION
The No. 1 skid control ECU (brake booster with master cylinder assembly) stores identification information sent from other ECUs when the vehicle is shipped from the factory and changes the control constant for each system (ABS, VSC, TRAC, etc.) based on the identification information.
NOTICE:
DTC C136F00 is output when an incorrect ECU is installed. If initialization is performed and learning occurs with an incorrect ECU installed, operations and functions will differ from those stored when the vehicle was shipped from the factory. Therefore, make sure that learning occurs properly.
|
DTC No. |
Detection Item |
DTC Detection Condition |
Trouble Area |
MIL |
Note |
|---|---|---|---|---|---|
|
C136F00 |
Non-learning of the Braking System information. |
Either of the following is detected:
|
|
Does not come on |
Output ECU: No. 1 skid control ECU (brake booster with master cylinder assembly) HINT: The DTC is cleared when the conditions return to normal. |
C136F00 DTC Detection Conditions
|
Vehicle Condition |
|||
|---|---|---|---|
|
Pattern 1 |
Pattern 2 |
||
|
Diagnosis Condition |
- |
- |
- |
|
Malfunction Status |
The drive system information sent from the hybrid vehicle control ECU does not match the information stored in the No. 1 skid control ECU (brake booster with master cylinder assembly) |
○ |
- |
|
No system information stored in the No. 1 skid control ECU (brake booster with master cylinder assembly) |
- |
○ |
|
|
Detection Time |
- |
- |
|
|
Number of Trips |
1 trip |
1 trip |
|
HINT:
DTC will be output when conditions for either of the patterns in the table above are met.
CAUTION / NOTICE / HINT
NOTICE:
After replacing the No. 1 skid control ECU (brake booster with master cylinder assembly), perform "Calibration" after performing "Reset Memory".
Click here
![2022 - 2024 MY RAV4 RAV4 HV [12/2021 - ]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster): UTILITY](/t3Portal/stylegraphics/info.gif)
PROCEDURE
|
1. |
CHECK PART NUMBER (HYBRID VEHICLE CONTROL ECU) |
(a) Check that the proper hybrid vehicle control ECU is installed.
OK:
Proper hybrid vehicle control ECU is installed.
| NG |
|
REPLACE HYBRID VEHICLE CONTROL ECU
|
|
|
2. |
CHECK PART NUMBER (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY) |
(a) Check that the proper No. 1 skid control ECU (brake booster with master cylinder assembly) is installed.
OK:
Proper No. 1 skid control ECU (brake booster with master cylinder assembly) is installed.
| NG |
|
REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY
|
|
|
3. |
SYSTEM INFORMATION MEMORIZATION |
(a) Perform system information memorization.
Click here
Chassis > Brake/EPB > Utility
|
Tester Display |
|---|
|
Reset Memory |
Chassis > Brake/EPB > Utility
|
Tester Display |
|---|
|
Calibration |
HINT:
After performing "Reset Memory" using the GTS to clear the memorized value of the No. 1 skid control ECU (brake booster with master cylinder assembly), DTC C136F00 will be stored until system information memorization is performed.
|
|
4. |
CLEAR DTC |
(a) Clear the DTCs.
Chassis > Brake Booster > Clear DTCs
(b) Turn the ignition switch off.
|
|
5. |
RECONFIRM DTC |
(a) Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.
(b) Check if the same DTC is output.
Chassis > Brake Booster > Trouble Codes
|
Result |
Proceed to |
|---|---|
|
DTC C136F00 is not output. |
A |
|
DTC C136F00 is output. |
B |
| A |
|
END |
| B |
|
REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY
|
|
|