| Last Modified: 01-30-2024 | 6.11:8.1.0 | Doc ID: RM1000000020MO8 |
| Model Year Start: 2022 | Model: RAV4 | Prod Date Range: [12/2021 - 10/2022] |
| Title: A25A-FKS (STARTING): STARTER (w/ Stop And Start System): REMOVAL; 2022 MY RAV4 [12/2021 - 10/2022] | ||
REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during starter assembly removal/installation are shown below.
Necessary Procedures After Parts Removed/Installed/Replaced
|
Replaced Part or Performed Procedure |
Necessary Procedure |
Effect/Inoperative Function when Necessary Procedure not Performed |
Link |
|---|---|---|---|
|
*: When performing learning using the Techstream.
Click here
|
|||
|
Battery terminal is disconnected/reconnected |
Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) |
Stop and start system |
|
|
Perform steering sensor zero point calibration |
Lane control system |
|
|
|
Parking support brake system (for Gasoline model)* |
|||
|
Pre-collision system |
|||
|
Memorize steering angle neutral point |
Parking assist monitor system |
|
|
|
Panoramic view monitor system (for Gasoline model) |
|
||
|
Reset back door close position |
Power back door system (for Gasoline model) |
|
|
|
Back door lock initialization |
Power door lock control system |
|
|
|
Starter assembly |
Clear the number of starter operations |
Stop and Start System |
|
NOTICE:
After the engine switch is turned off, the radio receiver assembly records various types of memory and settings. As a result, after turning the engine switch off, make sure to wait at least 85 seconds before disconnecting the cable from the negative (-) battery terminal.
PROCEDURE
1. PRECAUTION
NOTICE:
-
After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click here
![2019 - 2024 MY RAV4 RAV4 HV [11/2018 - ]; INTRODUCTION: REPAIR INSTRUCTION: PRECAUTION](/t3Portal/stylegraphics/info.gif)
- When the starter assembly is replaced, "ST NO. 1 relay" must also be replaced.
2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
Click here
3. REMOVE FRONT ENGINE MOUNTING INSULATOR
Click here
4. REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY
Click here
5. REMOVE INLET AIR CLEANER ASSEMBLY
Click here
6. REMOVE AIR CLEANER ASSEMBLY WITH AIR CLEANER HOSE
Click here
7. REMOVE FLYWHEEL HOUSING SIDE COVER
|
(a) Detach the claw as shown in the illustration to remove the flywheel housing side cover. |
|
8. REMOVE STARTER ASSEMBLY
|
(a) Remove the bolt and disconnect the engine wire from the vehicle body. |
|
|
(b) Detach the clamp to disconnect the radiator hose from the fan shroud assembly. |
|
(c) Detach the 2 clamps to disconnect the engine wire and No. 2 engine wire from the automatic transaxle assembly.
|
(d) Detach the 3 clamps to disconnect the radiator hose, vacuum hoses and No. 2 engine wire from the No. 1 radiator bracket. |
|
|
(e) Remove the bolt and No. 1 radiator bracket from the front engine mounting. |
|
|
(f) Disconnect the starter assembly connector. |
|
(g) Open the terminal cap.
|
(h) Remove the nut and disconnect the No. 2 engine wire from terminal 30. |
|
|
(i) Remove the 2 bolts and starter assembly from the cylinder block sub-assembly. |
|
|
|