Last Modified: 01-30-2024 |
6.11:8.1.0 |
Doc ID: RM10000000202XO |
Model Year Start: 2022 |
Model: RAV4 |
Prod Date Range: [12/2021 - 10/2022] |
Title: SEAT: FRONT SEATBACK HEATER (for Manual Seat): REMOVAL; 2022 MY RAV4 RAV4 HV [12/2021 - 10/2022] |
REMOVAL
CAUTION / NOTICE / HINT
CAUTION:
Wear protective gloves. Sharp areas on the parts may injure your hands.
The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during front seatback heater assembly removal/installation are shown below.
Necessary Procedures After Parts Removed/Installed/Replaced (for HV Model)
Replaced Part or Performed Procedure
|
Necessary Procedure
|
Effect/Inoperative Function when Necessary Procedure not Performed
|
Link
|
Disconnect cable from negative (-) auxiliary battery terminal
|
Perform steering sensor zero point calibration
|
Lane control system
|
|
Parking support brake system (for HV model)*
|
Pre-collision system
|
Memorize steering angle neutral point
|
Parking assist monitor system
|
|
Panoramic view monitor system (for HV model)
|
|
Reset back door close position
|
Power back door system (for HV model)
|
|
Power back door initialization
|
Power door lock control system
|
|
Front passenger seat
|
Zero point calibration (Occupant classification system)
|
-
Occupant classification system
-
Passenger airbag ON/OFF indicator
-
Airbag system (Front passenger side)
-
Seat belt warning system (Front passenger)
|
|
NOTICE:
After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, be sure to wait for the time specified in the following table before disconnecting the cable from the negative (-) auxiliary battery terminal.
Waiting Time before Disconnecting Cable from Negative (-) Auxiliary Battery Terminal
System Name
|
See Procedure
|
Vehicle enrolled in Toyota Audio Multimedia system or safety connect system
|
6 minutes
|
Vehicle not enrolled in Toyota Audio Multimedia system and safety connect system
|
1 minute
|
Necessary Procedures After Parts Removed/Installed/Replaced (for Gasoline Model)
Replaced Part or Performed Procedure
|
Necessary Procedure
|
Effect/Inoperative Function when Necessary Procedure not Performed
|
Link
|
Disconnect cable from negative (-) auxiliary battery terminal
|
Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes)
|
Stop and start system
|
|
Perform steering sensor zero point calibration
|
Lane control system
|
|
Parking support brake system (for Gasoline model)*
|
Pre-collision system
|
Memorize steering angle neutral point
|
Parking assist monitor system
|
|
Panoramic view monitor system (for Gasoline model)
|
|
Reset back door close position
|
Power back door system (for Gasoline model)
|
|
Power back door initialization
|
Power door lock control system
|
|
Front passenger seat
|
Zero point calibration (Occupant classification system)
|
-
Occupant classification system
-
Passenger airbag ON/OFF indicator
-
Airbag system (Front passenger side)
-
Seat belt warning system (Front passenger)
|
|
NOTICE:
After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, be sure to wait for the time specified in the following table before disconnecting the cable from the negative (-) auxiliary battery terminal.
Waiting Time before Disconnecting Cable from Negative (-) Auxiliary Battery Terminal
System Name
|
See Procedure
|
Vehicle enrolled in Toyota Audio Multimedia system or safety connect system
|
6 minutes
|
Vehicle not enrolled in Toyota Audio Multimedia system and safety connect system
|
1 minute
|
HINT:
-
Use the same procedure for the RH and LH sides.
-
The following procedure is for the LH side.
PROCEDURE
1. PRECAUTION
CAUTION:
Be sure to read Precaution thoroughly before servicing.
Click here
NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click here
2. REMOVE FRONT SEAT ASSEMBLY LH
Click here
3. REMOVE VERTICAL ADJUSTING HANDLE LH (for Driver Side)
Click here
4. REMOVE RECLINING HINGE COVER LH
Click here
5. REMOVE RECLINING ADJUSTER RELEASE HANDLE LH
Click here
6. REMOVE SEAT ADJUSTER COVER CAP LH (for Driver Side)
Click here
7. REMOVE FRONT SEAT CUSHION SHIELD LH (for Driver Side)
Click here
8. REMOVE FRONT SEAT CUSHION SHIELD RH (for Front Passenger Side)
Click here
9. REMOVE FRONT SEAT INNER CUSHION SHIELD LH (for Driver Side)
Click here
10. REMOVE FRONT SEAT INNER CUSHION SHIELD RH (for Front Passenger Side)
Click here
11. REMOVE SEPARATE TYPE FRONT SEATBACK ASSEMBLY
Click here
12. REMOVE SEPARATE TYPE FRONT SEATBACK COVER WITH PAD
Click here
13. REMOVE SEPARATE TYPE FRONT SEATBACK COVER
Click here
14. REMOVE FRONT SEATBACK HEATER ASSEMBLY LH (for Driver Side)
(a) Remove the 16 tag pins and front seatback heater assembly LH from the separate type front seatback cover.
NOTICE:
Be careful not to damage the separate type front seatback cover and front seatback heater assembly LH.
|
|
15. REMOVE FRONT SEATBACK HEATER ASSEMBLY RH (for Front Passenger Side)
(a) for Standard Seat Type:
(1) Remove the 16 tag pins and front seatback heater assembly RH from the separate type front seatback cover.
NOTICE:
Be careful not to damage the separate type front seatback cover and front seatback heater assembly RH.
|
|
(b) for Sports Seat Type:
(1) Remove the 14 tag pins and front seatback heater assembly RH from the separate type front seatback cover.
NOTICE:
Be careful not to damage the separate type front seatback cover and front seatback heater assembly RH.
|
|
|