Last Modified: 01-30-2024 |
6.11:8.1.0 |
Doc ID: RM10000000201WI |
Model Year Start: 2022 |
Model: RAV4 |
Prod Date Range: [12/2021 - 10/2022] |
Title: SUPPLEMENTAL RESTRAINT SYSTEMS: FRONT PASSENGER AIRBAG ASSEMBLY: REMOVAL; 2022 MY RAV4 RAV4 HV [12/2021 - 10/2022] |
REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during instrument panel passenger airbag assembly removal/installation are shown below.
Necessary Procedures After Parts Removed/Installed/Replaced (for Gasoline Model)
Replaced Part or Performed Procedure
|
Necessary Procedures
|
Effect/Inoperative Function When Necessary Procedures are not Performed
|
Link
|
Disconnect cable from negative (-) auxiliary battery terminal
|
Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes)
|
Stop and start system
|
|
Perform steering sensor zero point calibration
|
Lane control system
|
|
Parking support brake system (for Gasoline model)*
|
Pre-collision system
|
Memorize steering angle neutral point
|
Parking assist monitor system
|
|
Panoramic view monitor system (for Gasoline model)
|
|
Reset back door close position
|
Power back door system (for Gasoline model)
|
|
Back door lock initialization
|
Power door lock control system
|
|
NOTICE:
After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, be sure to wait for the time specified in the following table before disconnecting the cable from the negative (-) auxiliary battery terminal.
Waiting Time before Disconnecting Cable from Negative (-) Auxiliary Battery Terminal
System Name
|
See Procedure
|
Vehicle enrolled in Toyota Audio Multimedia system or safety connect system
|
6 minutes
|
Vehicle not enrolled in Toyota Audio Multimedia system and safety connect system
|
1 minute
|
Necessary Procedures After Parts Removed/Installed/Replaced (for HV Model)
Replaced Part or Performed Procedure
|
Necessary Procedures
|
Effect/Inoperative Function When Necessary Procedures are not Performed
|
Link
|
Disconnect cable from negative (-) auxiliary battery terminal
|
Perform steering sensor zero point calibration
|
Lane control system
|
|
Parking support brake system (for HV model)*
|
Pre-collision system
|
Memorize steering angle neutral point
|
Parking assist monitor system
|
|
Panoramic view monitor system (for HV model)
|
|
Reset back door close position
|
Power back door system (for HV model)
|
|
Back door lock initialization
|
Power door lock control system
|
|
NOTICE:
After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, be sure to wait for the time specified in the following table before disconnecting the cable from the negative (-) auxiliary battery terminal.
Waiting Time before Disconnecting Cable from Negative (-) Auxiliary Battery Terminal
System Name
|
See Procedure
|
Vehicle enrolled in Toyota Audio Multimedia system or safety connect system
|
6 minutes
|
Vehicle not enrolled in Toyota Audio Multimedia system and safety connect system
|
1 minute
|
PROCEDURE
1. PRECAUTION
CAUTION:
Be sure to read precaution thoroughly before servicing.
Click here
NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click here
2. REMOVE DECK BOARD ASSEMBLY (for HV Model)
Click here
3. REMOVE REAR NO. 2 FLOOR BOARD (for HV Model)
Click here
4. REMOVE BATTERY HOLE COVER (for HV Model)
Click here
5. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL
-
for A25A-FKS:
Click here
-
for A25A-FXS:
Click here
-
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
-
If the airbag deploys for any reason, it may cause a serious accident.
NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click here
6. REMOVE INSTRUMENT PANEL SAFETY PAD ASSEMBLY
Click here
7. REMOVE DEFROSTER NOZZLE ASSEMBLY
Click here
8. REMOVE NO. 3 HEATER TO REGISTER DUCT SUB-ASSEMBLY
Click here
9. REMOVE NO. 2 SIDE DEFROSTER NOZZLE DUCT
Click here
10. REMOVE NO. 2 INSTRUMENT PANEL WIRE
(a) Using a screwdriver, release the lock button and disconnect the 2 airbag connectors.
*a
|
Lock Button
|
*b
|
Wire Harness Clamp
|
*c
|
Guide
|
|
Protective Tape
|
|
Release in this Direction
|
NOTICE:
When disconnecting any airbag connector, take care not to damage the airbag wire harness.
HINT:
Tape the screwdriver tip before use.
(b) Detach the wire harness clamp and guide and remove the No. 2 instrument panel wire.
11. REMOVE INSTRUMENT PANEL PASSENGER AIRBAG ASSEMBLY
|
Deployment Side
|
-
When storing the instrument panel passenger airbag assembly, keep the airbag deployment side facing upward.
-
If the airbag deploys for any reason, it may cause a serious accident.
(b) Insert moulding remover B into the side of the airbag door facing the front of the vehicle and detach the hook.
|
|
(c) While holding the positions shown in the illustration, move the instrument panel passenger airbag assembly toward you, detach the hook near the rear of the vehicle, and then remove the instrument panel passenger airbag assembly.
|
Hold Here
|
|
Move in this Direction
|
|