| Last Modified: 01-30-2024 | 6.11:8.1.0 | Doc ID: RM10000000201F0 |
| Model Year Start: 2022 | Model: RAV4 HV | Prod Date Range: [12/2021 - ] |
| Title: HEATING / AIR CONDITIONING: CONDENSER (for HV Model): REMOVAL; 2022 - 2024 MY RAV4 HV [12/2021 - ] | ||
REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during cooler condenser assembly removal/installation are shown below.
Necessary Procedures After Parts Removed/Installed/Replaced
|
Replaced Part or Performed Procedures |
Necessary Procedures |
Effect/Inoperative Function when Necessary Procedures are not Performed |
Link |
|---|---|---|---|
|
Front bumper assembly (Including removal and installation) |
Front television camera view adjustment |
Panoramic view monitor system (for HV Model) |
|
PROCEDURE
1. RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM
Click here
![2019 - 2024 MY RAV4 RAV4 HV [02/2019 - ]; HEATING / AIR CONDITIONING: REFRIGERANT (for HFO-1234yf(R1234yf)): REPLACEMENT+](/t3Portal/stylegraphics/info.gif)
2. REMOVE FRONT BUMPER REINFORCEMENT SUB-ASSEMBLY
HINT:
Remove using the same procedure that is performed when replacement of the front bumper reinforcement sub-assembly is necessary.
Click here
3. REMOVE RADIATOR SHUTTER SUB-ASSEMBLY (w/ Grille Shutter)
Click here
4. REMOVE LOW PITCHED HORN ASSEMBLY
Click here
5. REMOVE VEHICLE APPROACHING SPEAKER ASSEMBLY (w/ Vehicle Proximity Notification System)
Click here
6. REMOVE INLET AIR CLEANER ASSEMBLY
Click here
7. DISCONNECT HOOD LOCK CONTROL CABLE ASSEMBLY
|
(a) Disconnect the hood lock control cable assembly from the clamp. |
|
8. REMOVE UPPER RADIATOR SUPPORT SUB-ASSEMBLY
(a) w/ Engine Hood Courtesy Switch
|
(1) Detach the clamp. |
|
(b) Detach the clamp.
|
*1 |
Radiator Support Cushion |
- |
- |
(c) Remove the 4 bolts.
(d) Detach the 2 radiator support cushions and remove the upper radiator support sub-assembly.
NOTICE:
Do not damage the cooler condenser assembly or radiator assembly when removing the upper radiator support sub-assembly.
9. DISCONNECT AIR CONDITIONING TUBE AND ACCESSORY ASSEMBLY
(a) Press the air conditioning tube and accessory assembly to the cooler condenser assembly, and then release the piping clamp lock.
NOTICE:
Do not apply excessive force to the air conditioning tube and accessory assembly.
|
*1 |
Air Conditioning Tube and Accessory Assembly |
*2 |
Cooler Condenser Assembly |
|
*3 |
Piping Clamp |
- |
- |
|
*a |
Press In |
- |
- |
(b) While releasing the piping clamp lock, use pliers or another tool to pinch near the rear end of the piping clamp, and then disconnect the air conditioning tube and accessory assembly as you buckle it.
NOTICE:
- If any foreign matter is attached to the connecting parts, brush it off or use compressed air to remove it before disconnecting the parts.
- Make sure that fragments of the piping clamp do not enter the piping.
- When the piping clamp is buckled, cracks form. Therefore, make sure to replace it with a new one.
- Remove any foreign matter from the connecting parts of the air conditioning tube and accessory assembly and cooler condenser assembly.
|
*1 |
Air Conditioning Tube and Accessory Assembly |
*2 |
Cooler Condenser Assembly |
|
*3 |
Piping Clamp |
- |
- |
|
*a |
Buckle |
*b |
Pull Out |
(c) Remove the 2 O-rings from the air conditioning tube and accessory assembly.
NOTICE:
Seal the openings of the disconnected parts with vinyl tape to prevent entry of moisture and foreign matter.
(d) Remove the piping clamp.
10. REMOVE NO. 1 RADIATOR AIR GUIDE RH
|
(a) Remove the clip. |
|
(b) Detach the guide and remove the No. 1 radiator air guide RH.
11. DISCONNECT NO. 1 COOLER REFRIGERANT DISCHARGE HOSE
|
(a) Remove the bolt and disconnect the No. 1 cooler refrigerant discharge hose. NOTICE: Do not apply excessive force to the No. 1 cooler refrigerant discharge hose. |
|
(b) Remove the O-ring from the No. 1 cooler refrigerant discharge hose.
NOTICE:
Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.
12. REMOVE COOLER CONDENSER ASSEMBLY (for TMC Made)
|
(a) Detach the claw. |
|
(b) Detach the guide and remove the cooler condenser assembly as shown in the illustration.
|
Remove in this Direction |
NOTICE:
Do not damage the cooler condenser assembly or radiator assembly when removing the cooler condenser assembly.
13. REMOVE COOLER CONDENSER ASSEMBLY (for TMMC Made)
HINT:
Use the same procedure described as for the cooler condenser assembly (for TMC Made).
|
|