- Power window regulator motor assembly LH
- Power window regulator motor assembly RH
- Rear door window regulator sub-assembly LH
- Rear door window regulator sub-assembly RH
- Rear door glass sub-assembly LH
- Rear door glass sub-assembly RH
- Rear door glass run LH
- Rear door glass run RH
| Last Modified: 01-30-2024 | 6.11:8.1.0 | Doc ID: RM10000000201E4 |
| Model Year Start: 2022 | Model: RAV4 | Prod Date Range: [12/2021 - 10/2022] |
| Title: DOOR LOCK: REAR DOOR LOCK: REMOVAL; 2022 MY RAV4 RAV4 HV [12/2021 - 10/2022] | ||
REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear door lock assembly removal/installation are shown below.
Necessary Procedure After Parts Removed/Installed/Replaced (for HV Model)
|
Replaced Part or Performed Procedures |
Necessary Procedures |
Effect/Inoperative Function When Necessary Procedures are not Performed |
Link |
|---|---|---|---|
|
*: When performing learning using the Techstream.
Click here
|
|||
|
Removal and installation of auxiliary battery terminal |
Perform steering sensor zero point calibration |
Lane control system |
|
|
Parking support brake system (for HV model)* |
|||
|
Pre-collision system |
|||
|
Memorize steering angle neutral point |
Parking assist monitor system |
|
|
|
Panoramic view monitor system (for HV model) |
|
||
|
Reset back door close position |
Power back door system (for HV model) |
|
|
|
Back door lock initialization |
Power door lock control system |
|
|
|
|
Initialize power window control system |
|
|
NOTICE:
After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, be sure to wait for the time specified in the following table before disconnecting the cable from the negative (-) auxiliary battery terminal.
Waiting Time before Disconnecting Cable from Negative (-) Auxiliary Battery Terminal
|
System Name |
See Procedure |
|---|---|
|
Vehicle enrolled in Toyota Audio Multimedia system or safety connect system |
6 minutes |
|
Vehicle not enrolled in Toyota Audio Multimedia system and safety connect system |
1 minute |
Necessary Procedure After Parts Removed/Installed/Replaced (for Gasoline Model)
|
Replaced Part or Performed Procedures |
Necessary Procedures |
Effect/Inoperative Function When Necessary Procedures are not Performed |
Link |
|---|---|---|---|
|
*: When performing learning using the Techstream.
Click here
|
|||
|
Removal and installation of auxiliary battery terminal |
Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) |
Stop and start system |
|
|
Perform steering sensor zero point calibration |
Lane control system |
|
|
|
Parking support brake system (for Gasoline model)* |
|||
|
Pre-collision system |
|||
|
Memorize steering angle neutral point |
Parking assist monitor system |
|
|
|
Panoramic view monitor system (for Gasoline model) |
|
||
|
Reset back door close position |
Power back door system (for Gasoline model) |
|
|
|
Back door lock initialization |
Power door lock control system |
|
|
|
Initialize power window control system |
|
|
NOTICE:
After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, be sure to wait for the time specified in the following table before disconnecting the cable from the negative (-) auxiliary battery terminal.
Waiting Time before Disconnecting Cable from Negative (-) Auxiliary Battery Terminal
|
System Name |
See Procedure |
|---|---|
|
Vehicle enrolled in Toyota Audio Multimedia system or safety connect system |
6 minutes |
|
Vehicle not enrolled in Toyota Audio Multimedia system and safety connect system |
1 minute |
HINT:
- Use the same procedure for the RH and LH sides.
- The procedure below is for the LH side.
- When performing disassembly for the rear door, disconnect the negative (-) auxiliary battery terminal after fully opening the rear door glass.
PROCEDURE
1. PRECAUTION
NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click here
![2019 - 2024 MY RAV4 RAV4 HV [11/2018 - ]; INTRODUCTION: REPAIR INSTRUCTION: PRECAUTION](/t3Portal/stylegraphics/info.gif)
2. REMOVE DECK BOARD ASSEMBLY (for HV Model)
Click here
3. REMOVE REAR NO. 2 FLOOR BOARD (for HV Model)
Click here
4. REMOVE BATTERY HOLE COVER (for HV Model)
Click here
5. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL
(a) for A25A-FXS:
Click here
(b) for A25A-FKS:
Click here
CAUTION:
- Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
- If the airbag deploys for any reason, it may cause a serious accident.
NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click here
6. REMOVE REAR DOOR INSIDE HANDLE BEZEL LH
Click here
7. REMOVE DOOR ASSIST GRIP COVER LH
Click here
8. REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL
Click here
9. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY LH
Click here
10. REMOVE REAR DOOR INNER GLASS WEATHERSTRIP LH
Click here
11. REMOVE REAR DOOR FRONT BELT SEAL LH
Click here
12. REMOVE REAR DOOR REAR BELT SEAL LH
Click here
13. REMOVE REAR DOOR SERVICE HOLE COVER LH
Click here
14. REMOVE REAR DOOR FRAME GARNISH LH
Click here
15. DISCONNECT REAR DOOR GLASS RUN LH
Click here
16. REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY LH
Click here
17. REMOVE REAR DOOR GLASS RUN LH
Click here
18. REMOVE REAR DOOR GLASS SUB-ASSEMBLY LH
Click here
19. REMOVE REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY LH
Click here
20. REMOVE REAR DOOR LOCK WITH MOTOR ASSEMBLY LH
(a) Using a T30 "TORX" socket wrench, remove the 3 "TORX" screws.
|
*a |
Release Plate |
|
Remove in this Direction |
(b) Remove the release plate of the rear door outside handle frame sub-assembly LH in the direction indicated by the arrow shown in the illustration to remove the rear door lock with motor assembly LH.
21. REMOVE DOOR LOCK WIRING HARNESS SEAL
|
(a) When reusing rear door lock with motor assembly LH: (1) Remove the door lock wiring harness seal from the rear door lock with motor assembly LH. |
|
22. REMOVE REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY
(a) Using a screwdriver with its tip wrapped with protective tape, detach the claw and open the cover.
|
|
Remove in this Direction |
|
Protective Tape |
(b) Detach the clamp and remove the rear door lock remote control cable assembly as shown in the illustration.
|
|
Remove in this Direction |
23. REMOVE REAR DOOR INSIDE LOCKING CABLE ASSEMBLY
(a) Using a screwdriver with its tip wrapped with protective tape, detach the claw and open the cover.
|
|
Remove in this Direction |
|
|
Protective Tape |
(b) Detach the clamp and remove the rear door inside locking cable assembly as shown in the illustration.
|
|
Remove in this Direction |
|
|