Last Modified: 01-30-2024 6.11:8.1.0 Doc ID: RM100000001ZV5T
Model Year Start: 2022 Model: RAV4 Prod Date Range: [12/2021 - 10/2022]
Title: UB80E (AUTOMATIC TRANSMISSION / TRANSAXLE): OIL COOLER: REMOVAL; 2022 MY RAV4 [12/2021 - 10/2022]

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during transmission oil cooler removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced

Replaced Part or Performed Procedure

Necessary Procedure

Effect/Inoperative Function when Necessary Procedure not Performed

Link

*: When performing learning using the Techstream.

Click here 2019 - 2022 MY RAV4 [11/2018 - 10/2022]; PARK ASSIST / MONITORING: PARKING SUPPORT BRAKE SYSTEM (for Gasoline Model): CALIBRATION

Battery terminal is disconnected/reconnected

Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes)

Stop and start system

2022 MY RAV4 [12/2021 - 10/2022]; STOP AND START: STOP AND START SYSTEM: PRECAUTION

Perform steering sensor zero point calibration

Lane control system

2022 - 2024 MY RAV4 RAV4 HV [12/2021 -        ]; PRE-COLLISION: PRE-COLLISION SYSTEM: INITIALIZATION

Parking support brake system (for Gasoline model)*

Pre-collision system

Memorize steering angle neutral point

Parking assist monitor system

2019 - 2022 MY RAV4 RAV4 HV [11/2018 - 10/2022]; PARK ASSIST / MONITORING: PARKING ASSIST MONITOR SYSTEM: INITIALIZATION

Panoramic view monitor system (for Gasoline model)

2019 - 2022 MY RAV4 [11/2018 - 10/2022]; PARK ASSIST / MONITORING: PANORAMIC VIEW MONITOR SYSTEM (for Gasoline Model): INITIALIZATION

Reset back door close position

Power back door system (for Gasoline model)

2019 - 2023 MY RAV4 [11/2018 - 10/2023]; DOOR / HATCH: POWER BACK DOOR SYSTEM (for Gasoline Model): INITIALIZATION

Back door lock initialization

Power door lock control system

2019 - 2024 MY RAV4 RAV4 HV [11/2018 -        ]; DOOR LOCK: POWER DOOR LOCK CONTROL SYSTEM: INITIALIZATION

ECM

Perform Vehicle Identification Number (VIN) or frame number registration

DTC P063051 is output

2021 - 2024 MY RAV4 RAV4 HV [08/2020 -        ]; A25A-FKS (ENGINE CONTROL): SFI SYSTEM: REGISTRATION

Code registration

Engine start function

w/ Smart Key System: 2022 - 2024 MY RAV4 [12/2021 -        ]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function, Gasoline Model): REGISTRATION

w/o Smart Key System: 2019 - 2022 MY RAV4 [11/2018 - 10/2022]; THEFT DETERRENT / KEYLESS ENTRY: IMMOBILISER SYSTEM (for Gasoline Model without Smart Key System): REGISTRATION

  • If transaxle compensation code read from ECM
    • Perform reset memory
    • Transfer transaxle compensation code
    • Perform road test to allow ECM to learn
  • Large shift shock
  • Deterioration of fuel efficiency

for Initialization: 2019 - 2024 MY RAV4 [11/2018 -        ]; UB80E (AUTOMATIC TRANSMISSION / TRANSAXLE): AUTOMATIC TRANSAXLE SYSTEM: INITIALIZATION

for Registration: 2019 - 2024 MY RAV4 [11/2018 -        ]; UB80E (AUTOMATIC TRANSMISSION / TRANSAXLE): AUTOMATIC TRANSAXLE SYSTEM: REGISTRATION

  • If transaxle compensation code not read from ECM
    • Perform reset memory
    • Transfer transaxle compensation code
    • Perform road test to allow ECM to learn

NOTICE:

After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, be sure to wait for the time specified in the following table before disconnecting the cable from the negative (-) battery terminal.

Waiting Time before Disconnecting Cable from Negative (-) Battery Terminal

System Name

See Procedure

Vehicle enrolled in Toyota Audio Multimedia system or safety connect system

6 minutes

Vehicle not enrolled in Toyota Audio Multimedia system and safety connect system

1 minute

PROCEDURE

1. REMOVE BATTERY

Click here 2021 - 2022 MY RAV4 [08/2020 - 10/2022]; MAINTENANCE: A25A-FKS BATTERY: REMOVAL

2. REMOVE ECM

Click here 2021 - 2022 MY RAV4 [08/2020 - 10/2022]; A25A-FKS (ENGINE CONTROL): ECM: REMOVAL

3. REMOVE BATTERY CLAMP SUB-ASSEMBLY

Click here 2022 MY RAV4 [12/2021 - 10/2022]; A25A-FKS (ENGINE MECHANICAL): ENGINE ASSEMBLY: REMOVAL+

4. REMOVE FRONT FENDER FRONT SPLASH SHIELD LH

Click here 2022 MY RAV4 [12/2021 - 10/2022]; A25A-FKS (ENGINE MECHANICAL): ENGINE ASSEMBLY: REMOVAL+

5. REMOVE FRONT FENDER FRONT SPLASH SHIELD RH

Click here 2022 MY RAV4 [12/2021 - 10/2022]; A25A-FKS (ENGINE MECHANICAL): ENGINE ASSEMBLY: REMOVAL+

6. REMOVE NO. 1 ENGINE UNDER COVER

Click here 2022 MY RAV4 [12/2021 - 10/2022]; A25A-FKS (ENGINE MECHANICAL): ENGINE ASSEMBLY: REMOVAL+

7. REMOVE NO. 2 ENGINE UNDER COVER ASSEMBLY

Click here 2022 MY RAV4 [12/2021 - 10/2022]; A25A-FKS (ENGINE MECHANICAL): ENGINE ASSEMBLY: REMOVAL+

8. REMOVE FRONT FENDER APRON SEAL LH

Click here 2022 MY RAV4 [12/2021 - 10/2022]; A25A-FKS (ENGINE MECHANICAL): ENGINE ASSEMBLY: REMOVAL+

9. DRAIN ENGINE COOLANT

Click here 2019 - 2024 MY RAV4 [11/2018 -        ]; MAINTENANCE: A25A-FKS COOLANT: REPLACEMENT+

10. DRAIN AUTOMATIC TRANSAXLE FLUID

Click here 2020 - 2024 MY RAV4 [01/2020 -        ]; UB80E (AUTOMATIC TRANSMISSION / TRANSAXLE): TRANSMISSION WIRE: REMOVAL+

11. DISCONNECT OUTLET NO. 1 OIL COOLER HOSE

(a) Slide the clip and disconnect the outlet No. 1 oil cooler hose from the oil cooler union sub-assembly.

HINT:

Use a container to catch any automatic transaxle fluid which flows out of the outlet No. 1 oil cooler hose and oil cooler union sub-assembly.

12. DISCONNECT INLET NO. 1 OIL COOLER HOSE

(a) Slide the clip and disconnect the inlet No. 1 oil cooler hose from the No. 1 oil cooler outlet tube sub-assembly.

HINT:

Use a container to catch any automatic transaxle fluid which flows out of the inlet No. 1 oil cooler hose and No. 1 oil cooler outlet tube sub-assembly.

13. REMOVE NO. 1 OIL COOLER TUBE SUB-ASSEMBLY WITHOUT HOSE

(a) Remove the 2 bolts to disconnect the No. 1 oil cooler tube sub-assembly without hose from the automatic transaxle case sub-assembly.

(b) Slide the clip and disconnect the inlet No. 2 oil cooler hose from the transmission oil cooler.

HINT:

Use a container to catch any automatic transaxle fluid which flows out of the inlet No. 2 oil cooler hose and transmission oil cooler.

(c) Slide the clip and disconnect the outlet No. 2 oil cooler hose to remove the No. 1 oil cooler tube sub-assembly without hose from the transmission oil cooler.

HINT:

Use a container to catch any automatic transaxle fluid which flows out of the outlet No. 2 oil cooler hose and transmission oil cooler.

(d) Slide the 4 clips and remove the inlet No. 1 oil cooler hose, inlet No. 2 oil cooler hose, outlet No. 1 oil cooler hose and outlet No. 2 oil cooler hose from the No. 1 oil cooler tube sub-assembly without hose.

*1

No. 1 Oil Cooler Tube Sub-assembly without Hose

*2

Inlet No. 1 Oil Cooler Hose

*3

Inlet No. 2 Oil Cooler Hose

*4

Outlet No. 1 Oil Cooler Hose

*5

Outlet No. 2 Oil Cooler Hose

14. DISCONNECT NO. 1 WATER BY-PASS HOSE

(a) Disengage the 3 clamps to remove the transmission breather clamp.

(b) Slide the clip and disconnect the No. 1 water by-pass hose from the transmission oil cooler.

HINT:

Use a container to catch any coolant which flows out of the No. 1 water by-pass hose and transmission oil cooler.

15. DISCONNECT WATER BY-PASS HOSE ASSEMBLY

(a) Slide the clip and disconnect the water by-pass hose assembly from the transmission oil cooler.

HINT:

Use a container to catch any coolant which flows out of the water by-pass hose assembly and transmission oil cooler.

16. REMOVE TRANSMISSION OIL COOLER

(a) Remove the 3 bolts and the transmission oil cooler from the automatic transaxle case sub-assembly.