HYBRID / BATTERY CONTROL: BATTERY ECU (for LITHIUM-ION BATTERY): REMOVAL; 2021 MY RAV4 HV [08/2020

Last Modified: 01-30-2024	6.11:8.1.0	Doc ID: RM100000001WM5O
Model Year Start: 2021	Model: RAV4 HV	Prod Date Range: [08/2020 - 12/2021]
Title: HYBRID / BATTERY CONTROL: BATTERY ECU (for LITHIUM-ION BATTERY): REMOVAL; 2021 MY RAV4 HV [08/2020 - 12/2021]

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during battery ECU assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced

Replaced Part or Performed Procedure	Necessary Procedures	Effect/Inoperative Function when Necessary Procedure not Performed
*: When performing learning using the Techstream. Click here
Auxiliary battery terminal is disconnected/reconnected	Perform steering sensor zero point calibration	Lane control system
		Parking support brake system*
		Pre-collision system
		Lighting system (EXT) (w/ AFS)
	Memorize steering angle neutral point	Parking assist monitor system
	Memorize steering angle neutral point	Panoramic view monitor system
	Reset back door close position	Power back door system
	Power back door initialization	Power door lock control system
Replacement of battery ECU assembly	Current sensor offset learning	DTCs are stored

CAUTION:

Orange wire harnesses and connectors indicate high-voltage circuits. To prevent electric shock, always follow the procedure described in the repair manual.
Click here
To prevent electric shock, wear insulated gloves when working on wire harnesses and components of the high voltage system.

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click here
The type of battery ECU assembly to be used varies depending on the vehicle model.

The type of battery ECU assembly can be confirmed by the color of the label.

*a	Black Label

If the wrong type of battery ECU assembly is installed, the power switch cannot be turned on (READY).
After installing the battery ECU assembly, perform the following to check that the power switch can be turned on (READY).
- Turn the power switch on (READY).
- Turn the power switch off and wait for 30 seconds or more.
- Turn the power switch on (READY) again.

PROCEDURE

1. WHEN REPLACING BATTERY ECU ASSEMBLY

HV battery learning values are stored in the battery ECU assembly and ECM and are used to detect malfunctions and illuminate the hybrid battery indicator light in the combination meter assembly. When either of these ECUs is replaced, the new ECU receives the HV battery learning values from the other ECU and stores them.

NOTICE:

Do not replace the battery ECU assembly and ECM at the same time as the HV battery learning values will be lost. However, if it is necessary to replace both ECUs at the same time, replace them by following the procedure below.
Do not replace the battery ECU assembly or ECM with a used one from another vehicle.

(a) Procedure when replacing both battery ECU assembly and ECM:

(1) Disconnect the cable from the negative (-) auxiliary battery terminal.

(2) Replace either ECU.

(3) Connect the cable to the negative (-) auxiliary battery terminal.

(4) Turn the power switch on (READY) and wait for 5 minutes or more.

(5) Turn the power switch off and disconnect the cable from the negative (-) auxiliary battery terminal.

(6) Replace the other ECU.

(7) Connect the cable to the negative (-) auxiliary battery terminal.

(8) Check that the power switch can be turned on (READY).

HINT:

If the battery ECU assembly and ECM are replaced at the same time without following the above procedure, replace either of the ECUs with its original one and then replace it again by following the above procedure. If the correct procedure is not followed, perform the procedure again from the beginning.

2. REMOVE SERVICE PLUG GRIP

Click here

3. DISCONNECT ENGINE ROOM MAIN WIRE

Click here

4. REMOVE CONNECTOR COVER ASSEMBLY

Click here

5. CHECK TERMINAL VOLTAGE

Click here

6. INSTALL CONNECTOR COVER ASSEMBLY

Click here

7. CONNECT ENGINE ROOM MAIN WIRE

Click here

8. REMOVE BENCH TYPE REAR SEAT CUSHION ASSEMBLY

Click here

9. REMOVE REAR SEAT CUSHION LOCK HOOK

Click here

10. REMOVE NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY

Click here

11. REMOVE REAR DOOR SCUFF PLATE LH

Click here

12. REMOVE NO. 3 BATTERY SERVICE COVER BOARD

Click here

13. REMOVE REAR DOOR SCUFF PLATE RH

HINT:

Use the same procedure as for the LH side.

14. REMOVE NO. 2 BATTERY SERVICE COVER BOARD

Click here

15. REMOVE BATTERY SERVICE COVER BOARD

Click here

16. REMOVE REAR SEAT CUSHION LEG SUB-ASSEMBLY

Click here

17. REMOVE NO. 1 HV BATTERY COVER PANEL RH

Click here

18. REMOVE HYBRID BATTERY HOSE ASSEMBLY

Click here

19. DISCONNECT FLOOR WIRE

Click here

20. REMOVE NO. 4 HV BATTERY PROTECTOR

Click here

21. DISCONNECT FLOOR WIRE

Click here

22. REMOVE UPPER HV BATTERY COVER SUB-ASSEMBLY

CAUTION:

Be sure to wear insulated gloves and protective goggles.

(a) Remove the 5 bolts, 6 nuts and upper HV battery cover sub-assembly from the HV battery.

*a	Bolt
*b	Nut

23. REMOVE NO. 1 HV BATTERY HOSE

CAUTION:

Be sure to wear insulated gloves and protective goggles.

(a) Remove the 2 clips.

(b) Disengage the 2 claws to remove the No. 1 HV battery hose from the HV battery.

24. REMOVE BATTERY ECU ASSEMBLY

CAUTION:

Be sure to wear insulated gloves and protective goggles.

(a) Disengage the clamp.

(b) Move the lock lever while pushing the lock, and disconnect the 3 battery ECU assembly connectors.

NOTICE:

Make sure to release the lock of the lock lever before moving it.

*a	Lever Lock

If the connector cannot be disconnected, check if the lock lever is completely unlocked.
Insulate each disconnected high-voltage connector with insulating tape. Wrap the connector from the wire harness side to the end of the connector.

NOTICE:

If the battery ECU assembly has been struck or dropped, replace it.