Last Modified: 01-30-2024 6.11:8.1.0 Doc ID: RM100000001QT72
Model Year Start: 2021 Model: RAV4 Prod Date Range: [08/2020 - 12/2021]
Title: ALIGNMENT / HANDLING DIAGNOSIS: FRONT WHEEL ALIGNMENT: ADJUSTMENT; 2021 MY RAV4 RAV4 HV [08/2020 - 12/2021]

ADJUSTMENT

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after completing the front wheel alignment procedure are shown below.

Necessary Procedures After Adjustment

Replaced Part or Performed Procedure

Necessary Procedure

Effect/Inoperative Function when Necessary Procedure not Performed

Link

Front wheel alignment adjustment

Gasoline Model

  1. Reset Memory
  2. Acceleration sensor zero point calibration and system information memorization

VSC malfunction

2019 - 2024 MY RAV4 RAV4 HV [11/2018 -        ]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/ Vacuum Brake Booster): UTILITY

HV Model

  1. Clear zero point calibration data and stored linear solenoid valve calibration data
  2. Initialization and calibration of the linear solenoid valve
  3. Yaw rate and acceleration sensor zero point calibration

VSC malfunction

2019 - 2021 MY RAV4 RAV4 HV [02/2019 - 12/2021]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster): UTILITY

CAUTION / NOTICE / HINT

Standard (Unloaded Vehicle)

Destination

North America

Mexico

Tire Size

225/65R17

225/60R18

235/55R19

225/65R17

225/60R18

235/55R19

Front Vehicle Height

A - B

117 mm (4.606 in.)

117 mm (4.606 in.)

117 mm (4.606 in.)

133 mm (5.236 in.)

133 mm (5.236 in.)

133 mm (5.236 in.)

Rear Vehicle Height

C - D

41 mm (1.614 in.)

41 mm (1.614 in.)

41 mm (1.614 in.)

60 mm (2.362 in.)

60 mm (2.362 in.)

60 mm (2.362 in.)

Camber

-0°05' (-0.08°)

-0°05' (-0.08°)

-0°05' (-0.08°)

-0°20' (-0.33°)

-0°20' (-0.33°)

-0°20' (-0.33°)

Caster

4°55' (4.92°)

4°55' (4.92°)

4°55' (4.92°)

5°00' (5.00°)

5°00' (5.00°)

5°00' (5.00°)

Steering Axis Inclination (Reference)

12°05' (12.08°)

12°05' (12.08°)

12°05' (12.08°)

12°30' (12.50°)

12°30' (12.50°)

12°30' (12.50°)

Toe-in

mm

2.3 mm (0.091 in.)

2.3 mm (0.091 in.)

2.3 mm (0.091 in.)

2.5 mm (0.098 in.)

2.5 mm (0.098 in.)

2.6 mm (0.102 in.)

deg

0°12' (0.20°)

0°12' (0.20°)

0°12' (0.19°)

0°13' (0.22°)

0°13' (0.22°)

0°13' (0.22°)

Tire Turning Angle

Inside

37°40' (37.67°)

37°40' (37.67°)

35°40' (35.67°)

37°15' (37.25°)

37°15' (37.25°)

35°15' (35.25°)

Outside

32°25' (32.42°)

32°25' (32.42°)

31°05' (31.08°)

32°10' (32.17°)

32°10' (32.17°)

30°50' (30.83°)

Tolerance

Camber

+/- 45' (0.75°)

Caster

+/- 45' (0.75°)

Toe-in

mm

+/- 2 mm (0.079 in.)

deg

+/- 10' (0.17°)

Tire Turning Angle

Inside

+/- 2°

Left-right Difference

Camber

45' (0.75°) or less

Caster

45' (0.75°) or less

PROCEDURE

1. INSPECT TIRES

Click here 2021 - 2024 MY RAV4 RAV4 HV [08/2020 -        ]; TIRE / WHEEL: TIRE AND WHEEL SYSTEM: INSPECTION

2. MEASURE VEHICLE HEIGHT

NOTICE:

  • Before inspecting the wheel alignment, adjust the vehicle height to the specified value.
  • Be sure to perform measurement on a level surface.
  • If it is necessary to go under the vehicle for measurement, confirm that the parking brake is applied and the vehicle is secured with chocks.
  • Inspect while the vehicle is unloaded.
  • The standard value shown here is a value that is used for performing a wheel alignment and does not indicate the height of an actual vehicle.

(a) Bounce the vehicle up and down at the corners to stabilize the suspension.

(b) Measure the vehicle height.

Check the values in the top table.

Click here 2021 MY RAV4 RAV4 HV [08/2020 - 12/2021]; ALIGNMENT / HANDLING DIAGNOSIS: FRONT WHEEL ALIGNMENT: ADJUSTMENT+

Measurement Points:

  • A: Ground clearance of front wheel center.
  • B: Ground clearance of center of bolt head of front lower No. 2 suspension arm sub-assembly and front suspension crossmember sub-assembly.
  • C: Ground clearance of rear wheel center.
  • D: Ground clearance of center of tip of threaded portion of rear lower No. 2 suspension arm assembly and rear suspension member sub-assembly.

3. INSPECT CAMBER, CASTER AND STEERING AXIS INCLINATION

NOTICE:

Inspect while the vehicle is unloaded.

(a) Install a camber-caster-kingpin gauge and place the front wheels on the center of a turning radius gauge.

*a

Turning Radius Gauge

*b

Camber-caster-kingpin Gauge

(b) Inspect the camber, caster and steering axis inclination.

Check the values in the top table.

Click here 2021 MY RAV4 RAV4 HV [08/2020 - 12/2021]; ALIGNMENT / HANDLING DIAGNOSIS: FRONT WHEEL ALIGNMENT: ADJUSTMENT+

4. ADJUST CAMBER

NOTICE:

Inspect toe-in after the camber has been adjusted.

(a) Remove the front wheel.

Click here 2019 - 2024 MY RAV4 RAV4 HV [11/2018 -        ]; MAINTENANCE: TIRE AND WHEEL: REMOVAL

(b) Remove the 2 nuts on the lower side of the front shock absorber assembly.

NOTICE:

Keep the bolts inserted.

(c) Remove the top and bottom bolts one at a time and confirm that the steering knuckle can move freely in the front shock absorber assembly.

HINT:

  • Reinstall each bolt after removing it and confirming steering knuckle movement.
  • If the steering knuckle does not move freely in the front shock absorber assembly, clean the contact surfaces of the front shock absorber assembly and the steering knuckle.

(d) Temporarily install the 2 nuts. (Step A)

(e) Fully push or pull the front axle hub in the direction of the required adjustment. (Step B)

(f) Fully push or pull the front axle hub in the direction of the required adjustment. (Step B)

(g) Install the front wheel.

Click here 2019 - 2024 MY RAV4 RAV4 HV [11/2018 -        ]; MAINTENANCE: TIRE AND WHEEL: INSTALLATION

(h) Bounce the vehicle up and down at the corners to stabilize the suspension.

(i) Check the camber.

Check the values in the top table.

Click here 2021 MY RAV4 RAV4 HV [08/2020 - 12/2021]; ALIGNMENT / HANDLING DIAGNOSIS: FRONT WHEEL ALIGNMENT: ADJUSTMENT+

(1) If the measured value is not within the specification, calculate the required adjustment amount using the formula below.

Camber adjustment amount = center of the specified range - measured value

Check the combination of the installed bolts. Select appropriate bolts from the tables below to adjust the camber to the specified values.

HINT:

Try to adjust the camber to the center of the specified values.

To move the axle hub toward (+) in step B

To move the axle hub toward (-) in step B

Refer to table (1) (To move the axle hub toward the positive side)

Refer to table (2) (To move the axle hub toward the negative side)

The vehicle body and suspension may be damaged if the camber cannot be correctly adjusted according to the table above.

NOTICE:

Replace the nut with a new one when replacing the bolt.

(2) Table (1) (To move the axle hub toward the positive side)

*A

Table (1) (To move the axle hub toward the positive side)

*B

Selected Bolt Combination

*a

Installed Bolt

*b

Adjusting Value

*c

Standard Bolt

*d

90105-17013

*e

90105-17014

*f

90105-17015

(3) Table (2) (To move the axle hub toward the negative side)

*A

Table (2) (To move the axle hub toward the negative side)

*B

Selected Bolt Combination

*a

Installed Bolt

*b

Adjusting Value

*c

Standard Bolt

*d

90105-17013

*e

90105-17014

*f

90105-17015

(j) If the camber was out of adjustment in the previous step, perform the adjust camber steps mentioned above. In step A, replace the existing bolts with the selected bolts.

HINT:

Replace one bolt at a time when replacing both bolts.

5. INSPECT TOE-IN

NOTICE:

Inspect while the vehicle is unloaded.

(a) Bounce the vehicle up and down at the corners to stabilize the suspension.

(b) Release the parking brake and move the shift lever to N (for Automatic transaxle, Hybrid transaxle).

(c) Push the vehicle straight ahead approximately 5 m (16.4 ft.). (Step C)

(d) Put tread center marks on the rearmost points of the front wheels and measure the distance between the marks (dimension B).

*a

Tread Center Mark

*b

Dimension B

Front of the Vehicle

(e) Slowly push the vehicle straight ahead to cause the front wheels to rotate 180°. Use the front tire valve as a reference point.

HINT:

Do not allow the wheels to rotate more than 180°. If the wheels rotate more than 180°, perform the procedure from step C again.

(f) Measure the distance between the tread center marks on the front of the wheels (dimension A).

Check the values in the top table.

Click here 2021 MY RAV4 RAV4 HV [08/2020 - 12/2021]; ALIGNMENT / HANDLING DIAGNOSIS: FRONT WHEEL ALIGNMENT: ADJUSTMENT+

*a

Dimension A

Front of the Vehicle

HINT:

Measure "B - A" only when "C + D" cannot be measured.

If the toe-in is not within the specified range, adjust it at the steering rack ends.

6. ADJUST TOE-IN

(a) Separate the steering rack boot clips from the steering rack boot.

(b) Loosen the tie rod end sub-assembly lock nuts.

(c) Turn the right and left steering rack ends by an equal amount to adjust the toe-in.

Check the values in the top table.

Click here 2021 MY RAV4 RAV4 HV [08/2020 - 12/2021]; ALIGNMENT / HANDLING DIAGNOSIS: FRONT WHEEL ALIGNMENT: ADJUSTMENT+

HINT:

  • If the toe-in measurement is more than the specified range, shorten the left and right steering rack ends until the measurement is within the specified range.
  • If the toe-in measurement is less than the specified range, extend the left and right steering rack ends until the measurement is within the specified range.

Front of the Vehicle

HINT:

Perform adjustments so that the value is as close as possible to the median of the specified range.

(d) Make sure that the thread length of the right and left steering rack ends are the same.

(e) Tighten the tie rod end sub-assembly lock nuts.

Click here 2019 - 2024 MY RAV4 RAV4 HV [02/2019 -        ]; STEERING GEAR / LINKAGE: STEERING GEAR: INSTALLATION+

(f) Place the steering rack boots on the seats and install the steering rack boot clips.

(1) for LH side:

Click here 2019 - 2024 MY RAV4 RAV4 HV [02/2019 -        ]; STEERING GEAR / LINKAGE: STEERING GEAR: REASSEMBLY+

(2) for RH side:

HINT:

Perform the same procedure as for the LH side.

7. INSPECT WHEEL ANGLE

(a) Put tread center marks on the rearmost points of a turning radius gauge.

*a

Inside

*b

Outside

Front of the Vehicle

(b) Turn the steering wheel fully to the left and right and measure the turning angle.

Check the values in the top table.

Click here 2021 MY RAV4 RAV4 HV [08/2020 - 12/2021]; ALIGNMENT / HANDLING DIAGNOSIS: FRONT WHEEL ALIGNMENT: ADJUSTMENT+

NOTICE:

Inspect while the vehicle is unloaded.

  • If the right and left inside wheel angles differ from the specified value, check and adjust the right and left steering rack end lengths.

8. ELECTRONICALLY CONTROLLED BRAKE SYSTEM CALIBRATION

For HV models: 2019 - 2021 MY RAV4 RAV4 HV [02/2019 - 12/2021]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster): UTILITY

For Gasoline models: 2019 - 2024 MY RAV4 RAV4 HV [11/2018 -        ]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/ Vacuum Brake Booster): UTILITY