| Last Modified: 01-30-2024 | 6.11:8.1.0 | Doc ID: RM100000001OBE2 |
| Model Year Start: 2020 | Model: RAV4 HV | Prod Date Range: [06/2020 - ] |
| Title: HYBRID / BATTERY CONTROL: HYBRID BATTERY SYSTEM (for LITHIUM-ION BATTERY): P062F44; Hybrid/EV Battery Energy Control Module EEPROM Data Memory Failure; 2020 - 2024 MY RAV4 HV [06/2020 - ] | ||
|
DTC |
P062F44 |
Hybrid/EV Battery Energy Control Module EEPROM Data Memory Failure |
DESCRIPTION
The battery ECU assembly monitors its internal operation and will store these DTCs when it detects an internal malfunction.
|
DTC No. |
Detection Item |
DTC Detection Condition |
Trouble Area |
MIL |
Warning Indicate |
|---|---|---|---|---|---|
|
P062F44 |
Hybrid/EV Battery Energy Control Module EEPROM Data Memory Failure |
ECU internal malfunction (1 trip detection logic) |
Battery ECU assembly |
Comes on |
Master Warning: Does not come on |
MONITOR DESCRIPTION
The battery ECU assembly monitors its internal operation. If the internal operation is malfunctioning, the battery ECU assembly illuminates the MIL and stores a DTC.
MONITOR STRATEGY
|
Related DTCs |
P062F (INF P062F44): Internal control module EEPROM (battery energy control module) |
|
Required sensors/components |
Battery ECU assembly |
|
Frequency of operation |
Continuous |
|
Duration |
TMC's intellectual property |
|
MIL operation |
Immediately |
|
Sequence of operation |
None |
TYPICAL ENABLING CONDITIONS
|
The monitor will run whenever the following DTCs are not stored |
TMC's intellectual property |
|
Other conditions belong to TMC's intellectual property |
- |
TYPICAL MALFUNCTION THRESHOLDS
|
TMC's intellectual property |
- |
COMPONENT OPERATING RANGE
|
Battery ECU assembly |
DTC P062F (INF P062F44) is not detected |
CONFIRMATION DRIVING PATTERN
HINT:
-
After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Click here
![2020 - 2024 MY RAV4 HV [06/2020 - ]; HYBRID / BATTERY CONTROL: HYBRID BATTERY SYSTEM (for LITHIUM-ION BATTERY): UTILITY](/t3Portal/stylegraphics/info.gif)
-
When clearing the permanent DTCs, refer to the "CLEAR PERMANENT DTC" procedure.
Click here
- Connect the Techstream to the DLC3.
- Turn the ignition switch to ON and turn the Techstream on.
- Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
- Turn the ignition switch off and wait for 2 minutes or more.
- Turn the ignition switch to ON and turn the Techstream on.
-
With ignition switch ON and wait for 30 seconds or more.[*1]
HINT:
[*1]: Normal judgment procedure.
The normal judgment procedure is used to complete DTC judgment and also used when clearing permanent DTCs.
- Enter the following menus: Powertrain / HV Battery / Utility / All Readiness.
-
Check the DTC judgment result.
HINT:
- If the judgment result shows NORMAL, the system is normal.
- If the judgment result shows ABNORMAL, the system has a malfunction.
- If the judgment result shows INCOMPLETE, perform the normal judgment procedure again.
PROCEDURE
|
1. |
CHECK DTC OUTPUT (HEALTH CHECK) |
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Enter the following menus: System Select / Health Check.
(e) Check for DTCs.
|
Result |
Proceed to |
|---|---|
|
P062F44 is output from the hybrid battery system. |
A |
|
P062F44 is output from any system other than the hybrid battery system. |
B |
(f) Turn the ignition switch off.
| A |
|
REPLACE BATTERY ECU ASSEMBLY
|
| B |
|
GO TO PERFORM DIAGNOSIS FOR RESPECTIVE SYSTEM |
|
|