- Reclining motor (Front seatback frame sub-assembly (driver seat)) (Including removal and installation)
- Slide motor (Front seat adjuster assembly (driver seat)) (Including removal and installation)
- Power seat lifter motor assembly (driver seat) (Including removal and installation)
- Power seat tilt motor assembly (driver seat) (Including removal and installation)
| Last Modified: 01-30-2024 | 6.11:8.1.0 | Doc ID: RM100000001LSSR |
| Model Year Start: 2020 | Model: RAV4 | Prod Date Range: [10/2019 - 08/2020] |
| Title: SEAT: FRONT POWER SEAT MOTOR ASSEMBLY: REMOVAL; 2020 MY RAV4 RAV4 HV [10/2019 - 08/2020] | ||
REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during power seat lifter motor assembly and power seat tilt motor assembly removal/installation are shown below.
Necessary Procedures After Parts Removed/Installed/Replaced (for HV Model)
|
Replaced Part or Performed Procedure |
Necessary Procedure |
Effect/Inoperative Function when Necessary Procedure not Performed |
Link |
|---|---|---|---|
|
*: When performing learning using the Techstream.
Click here
|
|||
|
Disconnect cable from negative (-) auxiliary battery terminal |
Perform steering sensor zero point calibration |
Lane control system |
|
|
Parking support brake system (for HV model)* |
|||
|
Pre-collision system |
|||
|
Lighting system (EXT)(w/ AFS) |
|||
|
Memorize steering angle neutral point |
Parking assist monitor system |
|
|
|
Panoramic view monitor system (for HV model) |
|
||
|
Reset back door close position |
Power back door system (for HV model) |
|
|
|
Power back door initialization |
Power door lock control system |
|
|
|
|
Initialize position control ECU |
Front power seat control system (for HV model with memory) |
|
NOTICE:
After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, be sure to wait for the time specified in the following table before disconnecting the cable from the negative (-) auxiliary battery terminal.
Waiting Time before Disconnecting Cable from Negative (-) Auxiliary Battery Terminal
|
System Name |
See Procedure |
|---|---|
|
Vehicle enrolled in Toyota Audio Multimedia system or safety connect system |
6 minutes |
|
Vehicle not enrolled in Toyota Audio Multimedia system and safety connect system |
1 minute |
Necessary Procedures After Parts Removed/Installed/Replaced (for Gasoline Model)
|
Replaced Part or Performed Procedure |
Necessary Procedure |
Effect/Inoperative Function when Necessary Procedure not Performed |
Link |
|---|---|---|---|
|
*: When performing learning using the Techstream.
Click here
|
|||
|
Disconnect cable from negative (-) auxiliary battery terminal |
Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) |
Stop and start system |
|
|
Perform steering sensor zero point calibration |
Lane control system |
|
|
|
Parking support brake system (for Gasoline model)* |
|||
|
Pre-collision system |
|||
|
Memorize steering angle neutral point |
Parking assist monitor system |
|
|
|
Panoramic view monitor system (for Gasoline model) |
|
||
|
Reset back door close position |
Power back door system (for Gasoline model) |
|
|
|
Power back door initialization |
Power door lock control system |
|
|
|
Initialize position control ECU |
Front power seat control system (for Gasoline model with memory) |
|
NOTICE:
After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, be sure to wait for the time specified in the following table before disconnecting the cable from the negative (-) auxiliary battery terminal.
Waiting Time before Disconnecting Cable from Negative (-) Auxiliary Battery Terminal
|
System Name |
See Procedure |
|---|---|
|
Vehicle enrolled in Toyota Audio Multimedia system or safety connect system |
6 minutes |
|
Vehicle not enrolled in Toyota Audio Multimedia system and safety connect system |
1 minute |
CAUTION:
-
Wear protective gloves. Sharp areas on the parts may injure your hands.
- There is risk of injury.
PROCEDURE
1. PRECAUTION
CAUTION:
-
Be sure to read Precaution thoroughly before servicing.
-
w/ Occupant Classification System:
Click here
![2019 - 2020 MY RAV4 RAV4 HV [02/2019 - 08/2020]; SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM (w/ Occupant Classification System): PRECAUTION](/t3Portal/stylegraphics/info.gif)
-
w/o Occupant Classification System:
Click here
-
w/ Occupant Classification System:
-
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
- If an SRS part is accidentally deployed, it may cause a serious injury.
NOTICE:
-
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click here
-
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click here
2. REMOVE FRONT SEAT ASSEMBLY LH
Click here
3. REMOVE FRONT SEAT FRONT CUSHION SHIELD LH
Click here
4. REMOVE FRONT SEAT CUSHION SHIELD LH
Click here
5. REMOVE FRONT SEAT INNER CUSHION SHIELD LH
Click here
6. REMOVE SEPARATE TYPE FRONT SEATBACK ASSEMBLY
Click here
7. REMOVE SEPARATE TYPE FRONT SEAT CUSHION COVER WITH PAD
Click here
8. REMOVE LH SEAT RECLINING ADJUSTER INSIDE COVER
Click here
9. REMOVE POWER SEAT LIFTER MOTOR ASSEMBLY LH
|
(a) Disconnect the connector. |
|
|
(b) Remove the 3 nuts, front seat adjuster plate LH and vertical adjuster spacer. |
|
(c) Remove the power seat lifter motor assembly LH.
NOTICE:
Do not damage or dirty the gears of the power seat lifter motor assembly LH and front seat adjuster assembly LH.
10. REMOVE POWER SEAT TILT MOTOR ASSEMBLY LH
|
(a) Disconnect the connector. |
|
(b) Detach the clamp.
|
(c) Remove the 3 bolts and power seat tilt motor assembly LH. NOTICE: Do not damage or dirty the gears of the power seat tilt motor assembly LH and front seat adjuster assembly LH. |
|
|
|