AXLE AND DIFFERENTIAL: FRONT AXLE HUB BOLT: REPLACEMENT; 2020 MY RAV4 RAV4 HV [10/2019

Last Modified: 01-30-2024	6.11:8.1.0	Doc ID: RM100000001LRF1
Model Year Start: 2020	Model: RAV4	Prod Date Range: [10/2019 - 08/2020]
Title: AXLE AND DIFFERENTIAL: FRONT AXLE HUB BOLT: REPLACEMENT; 2020 MY RAV4 RAV4 HV [10/2019 - 08/2020]

REPLACEMENT

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during front axle hub bolt removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced (for HV Model:)

Replaced Part or Performed Procedure	Necessary Procedure	Effect/Inoperative Function when Necessary Procedure not Performed
*: When performing learning using the Techstream. Click here
Auxiliary battery terminal is disconnected/reconnected	Perform steering sensor zero point calibration	Lane control system
		Parking support brake system (for HV model)*
		Pre-collision system
		Lighting system (EXT)(w/ AFS)
	Memorize steering angle neutral point	Parking assist monitor system
	Memorize steering angle neutral point	Panoramic view monitor system (for HV model)
	Reset back door close position	Power back door system (for HV model)
	Back door lock initialization	Power door lock control system

NOTICE:

After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, be sure to wait for the time specified in the following table before disconnecting the cable from the negative (-) auxiliary battery terminal.

Waiting Time before Disconnecting Cable from Negative (-) Auxiliary Battery Terminal

System Name	See Procedure
Vehicle enrolled in Toyota Audio Multimedia system or safety connect system	6 minutes
Vehicle not enrolled in Toyota Audio Multimedia system and safety connect system	1 minute

HINT:

Use the same procedure for the RH and LH sides.
The following procedure is for the LH side.

PROCEDURE

1. DISABLE BRAKE CONTROL (w/o Vacuum Brake Booster)

Click here

2. REMOVE FRONT WHEEL

Click here

3. DISCONNECT FRONT FLEXIBLE HOSE

(a) Remove the bolt and disconnect the front flexible hose from the front shock absorber assembly.

4. DISCONNECT FRONT DISC BRAKE CALIPER ASSEMBLY LH

(a) Remove the 2 bolts and disconnect the front disc brake caliper assembly from the steering knuckle.

NOTICE:

Use wire or an equivalent tool to keep the front disc brake caliper assembly from hanging by the front flexible hose.

5. REMOVE FRONT DISC

Click here

6. REMOVE FRONT AXLE HUB BOLT LH

(a) Temporarily install 2 service nuts to the front axle hub bolts as shown in the illustration.

Recommended service nut:

Thread diameter: 12.0 mm (0.472 in.)

Thread pitch: 1.5 mm (0.0591 in.)

NOTICE:

Install the service nuts to prevent damage to the front axle hub bolts.

*a	Service Nut
*b	Hold
*c	Turn

(b) Using SST and a screwdriver or an equivalent tool to hold the front axle hub sub-assembly, remove the front axle hub bolt.

SST: 09650-17011

NOTICE:

Do not damage the threads of the front axle hub bolts.

7. INSTALL FRONT AXLE HUB BOLT LH

(a) Temporarily install a new front axle hub bolt to the front axle hub sub-assembly.

(b) Install a washer and service nut to the front axle hub bolt as shown in the illustration.

Recommended service nut:

Thread diameter: 12.0 mm (0.472 in.)

Thread pitch: 1.5 mm (0.0591 in.)

HINT:

Recommended washer thickness is 5 mm (0.197 in.) or more.

*a	Service Nut
*b	Washer
*c	Hold
*d	Turn

(c) Using a screwdriver or an equivalent tool to hold the front axle hub sub-assembly, install the front axle hub bolt by tightening the service nut.

NOTICE:

Install the service nuts to prevent damage to the front axle hub bolts.
Do not damage the threads of the front axle hub bolts.

(d) Remove the 3 service nuts and washer from the 3 front axle hub bolts.

8. INSTALL FRONT DISC

Click here

9. INSTALL FRONT DISC BRAKE CALIPER ASSEMBLY LH

(a) Install the front disc brake caliper assembly to the steering knuckle with the 2 bolts.

Torque:

for Steel Steering Knuckle :

107 N·m {1091 kgf·cm, 79 ft·lbf}

for Aluminum Steering Knuckle :

150 N·m {1530 kgf·cm, 111 ft·lbf}

NOTICE:

Do not twist the front flexible hose when installing the front disc brake caliper assembly.
Make sure that there is no foreign matter on the threads of the bolt.

10. CONNECT FRONT FLEXIBLE HOSE

(a) Set the 2 front speed sensor LH hooks on the front shock absorber assembly LH.

Hook

NOTICE:

Do not twist the front speed sensor when installing it.

(b) Connect the front speed sensor and front flexible hose to the front shock absorber assembly with the bolt.

Torque:

29 N·m {296 kgf·cm, 21 ft·lbf}

NOTICE:

Do not twist the front flexible hose when installing it.

11. INSTALL FRONT WHEEL

Click here

12. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL (w/o Vacuum Brake Booster)

(a) Connect the reservoir level switch connector.

(b) Connect the cable to the negative (-) auxiliary battery terminal.

Click here

(1) Turn the ignition switch on (READY).

(2) Depress the brake pedal and release it.

(3) Clear the DTCs.

Click here