- Replacement of throttle body with motor assembly
- Replacement of EGR valve assembly
- Gas leaks from exhaust system
| Last Modified: 01-30-2024 | 6.11:8.1.0 | Doc ID: RM100000001LRBN |
| Model Year Start: 2020 | Model: RAV4 | Prod Date Range: [10/2019 - 08/2020] |
| Title: A25A-FKS (COOLING): THERMOSTAT: REMOVAL; 2020 MY RAV4 [10/2019 - 08/2020] | ||
REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during water inlet with thermostat sub-assembly removal/installation are shown below.
Necessary Procedures After Parts Removed/Installed/Replaced
|
Replaced Part or Performed Procedure |
Necessary Procedure |
Effect/Inoperative Function when Necessary Procedure not Performed |
Link |
|---|---|---|---|
|
*: When performing learning using the Techstream.
Click here
|
|||
|
Battery terminal is disconnected/reconnected |
Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) |
Stop and start system |
|
|
Perform steering sensor zero point calibration |
Lane control system |
|
|
|
Parking support brake system (for Gasoline model)* |
|||
|
Pre-collision system |
|||
|
Memorize steering angle neutral point |
Parking assist monitor system |
|
|
|
Panoramic view monitor system (for Gasoline model) |
|
||
|
Reset back door close position |
Power back door system (for Gasoline model) |
|
|
|
Back door lock initialization |
Power door lock control system |
|
|
|
|
Inspection after repair |
|
w/ Canister Pump Module:
w/o Canister Pump Module:
|
NOTICE:
-
After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, be sure to wait for the time specified in the following table before disconnecting the cable from the negative (-) battery terminal.
Waiting Time before Disconnecting Cable from Negative (-) Battery Terminal
System Name
See Procedure
Vehicle enrolled in Toyota Audio Multimedia system or safety connect system
6 minutes
Vehicle not enrolled in Toyota Audio Multimedia system and safety connect system
1 minute
-
This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.
Click here
![2019 - 2024 MY RAV4 RAV4 HV [11/2018 - ]; INTRODUCTION: REPAIR INSTRUCTION: PRECAUTION](/t3Portal/stylegraphics/info.gif)
PROCEDURE
1. DRAIN ENGINE COOLANT
Click here
2. REMOVE INTAKE MANIFOLD
Click here
3. REMOVE GENERATOR ASSEMBLY
-
for 100 A, 130 A Type:
Click here
-
for 150 A Type:
Click here
-
for VALEO Made:
Click here
4. DISCONNECT NO. 2 RADIATOR HOSE
|
(a) Slide the clip and disconnect the No. 2 radiator hose from the water inlet with thermostat sub-assembly. |
|
5. REMOVE WATER INLET WITH THERMOSTAT SUB-ASSEMBLY
|
(a) Disconnect the water inlet with thermostat sub-assembly connector. |
|
|
(b) Slide the clip and disconnect the No. 7 water by-pass hose from the water inlet with thermostat sub-assembly. NOTICE:
HINT: When disconnecting the No. 7 water by-pass hose, slide the clip, rotate the hose and pull it straight off the pipe. |
|
|
(c) Using an 8 mm socket wrench, remove the 2 bolts and water inlet with thermostat sub-assembly. |
|
|
(d) Remove the gasket from the water inlet with thermostat sub-assembly. |
|
|
|