Last Modified: 01-30-2024 6.11:8.1.0 Doc ID: RM100000001KZ01
Model Year Start: 2020 Model: RAV4 Prod Date Range: [10/2019 - 08/2020]
Title: STOP AND START: BACKUP BOOST CONVERTER: REMOVAL; 2020 MY RAV4 [10/2019 - 08/2020]

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during eco-run vehicle converter assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced

Replaced Part or Performed Procedure

Necessary Procedure

Effect/Inoperative Function when Necessary Procedure not Performed

Link
*: When performing learning using the Techstream.

Click here 2019 - 2022 MY RAV4 [11/2018 - 10/2022]; PARK ASSIST / MONITORING: PARKING SUPPORT BRAKE SYSTEM (for Gasoline Model): CALIBRATION

Battery terminal is disconnected/reconnected

Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes)

Stop and start system

2019 - 2021 MY RAV4 [11/2018 - 12/2021]; STOP AND START: STOP AND START SYSTEM: PRECAUTION

Perform steering sensor zero point calibration

Lane control system

2019 - 2021 MY RAV4 RAV4 HV [11/2018 - 12/2021]; PRE-COLLISION: PRE-COLLISION SYSTEM: INITIALIZATION

Parking support brake system*

Pre-collision system

Memorize steering angle neutral point

Parking assist monitor system

2019 - 2022 MY RAV4 RAV4 HV [11/2018 - 10/2022]; PARK ASSIST / MONITORING: PARKING ASSIST MONITOR SYSTEM: INITIALIZATION

Panoramic view monitor system

2019 - 2022 MY RAV4 [11/2018 - 10/2022]; PARK ASSIST / MONITORING: PANORAMIC VIEW MONITOR SYSTEM (for Gasoline Model): INITIALIZATION

Reset back door close position

Power back door system

2019 - 2023 MY RAV4 [11/2018 - 10/2023]; DOOR / HATCH: POWER BACK DOOR SYSTEM (for Gasoline Model): INITIALIZATION

Back door lock initialization

Power door lock control system

2019 - 2024 MY RAV4 RAV4 HV [11/2018 -        ]; DOOR LOCK: POWER DOOR LOCK CONTROL SYSTEM: INITIALIZATION

PROCEDURE

1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notices before proceeding with work.

Click here 2019 - 2024 MY RAV4 RAV4 HV [11/2018 -        ]; INTRODUCTION: REPAIR INSTRUCTION: PRECAUTION

2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click here 2020 MY RAV4 RAV4 HV [10/2019 - 06/2020]; INTRODUCTION: REPAIR INSTRUCTION: INITIALIZATION 2020 MY RAV4 RAV4 HV [06/2020 - 08/2020]; INTRODUCTION: REPAIR INSTRUCTION: INITIALIZATION

3. REMOVE FRONT BUMPER ASSEMBLY

  • for Off Road Package:

    Click here 2019 - 2020 MY RAV4 RAV4 HV [02/2019 - 08/2020]; EXTERIOR PANELS / TRIM: FRONT BUMPER (for Off Road Package): REMOVAL

  • except Off Road Package:

    Click here 2019 - 2020 MY RAV4 RAV4 HV [02/2019 - 08/2020]; EXTERIOR PANELS / TRIM: FRONT BUMPER (except Off Road Package): REMOVAL

4. REMOVE ECO-RUN VEHICLE CONVERTER ASSEMBLY

(a) Move the lock lever and disconnect the connector from the eco-run vehicle converter assembly.

*a

Lock Lever

(b) Remove the 2 nuts and eco-run vehicle converter assembly.

5. REMOVE NO. 1 CONVERTER CONTROL BRACKET

(a) Remove the 2 bolts and No. 1 converter control bracket from the eco-run vehicle converter assembly.