- Register transmitter ID
- Initialize tire pressure warning system
| Last Modified: 01-30-2024 | 6.11:8.1.0 | Doc ID: RM100000001KSFU |
| Model Year Start: 2020 | Model: RAV4 | Prod Date Range: [10/2019 - 12/2021] |
| Title: TIRE PRESSURE MONITORING: TIRE PRESSURE WARNING VALVE: REMOVAL; 2020 - 2021 MY RAV4 RAV4 HV [10/2019 - 12/2021] | ||
REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the Tire pressure warning valve and transmitter removal/installation are shown below.
Necessary Procedures After Parts Removed/Installed/Replaced (for HV Model:)
|
Replaced Part or Performed Procedure |
Necessary Procedure |
Effect/Inoperative Function when Necessary Procedure not Performed |
Link |
|---|---|---|---|
|
Tire pressure warning valve and transmitter |
|
|
for Initialization:
for Registration:
|
Necessary Procedures After Parts Removed/Installed/Replaced (for Gasoline Model:)
|
Replaced Part or Performed Procedure |
Necessary Procedure |
Effect/Inoperative Function when Necessary Procedure not Performed |
Link |
|---|---|---|---|
|
Tire pressure warning valve and transmitter |
|
|
for Initialization:
for Registration:
|
PROCEDURE
1. REMOVE FRONT WHEEL
Click here
![2019 - 2024 MY RAV4 RAV4 HV [11/2018 - ]; MAINTENANCE: TIRE AND WHEEL: REMOVAL+](/t3Portal/stylegraphics/info.gif)
2. REMOVE REAR WHEEL
Click here
3. REMOVE FULL SIZE SPARE TIRE (w/ Full Size Spare Tire)
4. REMOVE TIRE PRESSURE WARNING VALVE AND TRANSMITTER (for Type A)
(a) Remove the tire valve cap.
NOTICE:
Keep the removed tire valve cap.
(b) Remove the valve core to release the air from the tire.
NOTICE:
Make sure that a sufficient amount of air has been released.
|
(c) Using a tire remover, remove the tire from the disc wheel. NOTICE:
|
|
|
(d) Using a T10 "TORX" socket wrench, remove the bolt and tire pressure monitor sensor from the tubeless tire valve. |
|
(e) Cut the tubeless tire valve and remove it by pulling from the outer side of the disc wheel as shown in the illustration.
|
*1 |
Tubeless Tire Valve |
|
Cutting Area |
5. REMOVE TIRE PRESSURE WARNING VALVE AND TRANSMITTER (for Type B, Type D)
(a) Remove the tire valve cap and valve core to release the air from the tire.
NOTICE:
Keep the removed tire valve cap.
(b) After ensuring that a sufficient amount of air has been released, remove the nut and washer used to secure the tire pressure warning valve and transmitter. Then drop the tire pressure warning valve and transmitter with the grommet into the tire.
HINT:
The grommet may remain attached to the rim.
|
(c) After dropping the tire pressure warning valve and transmitter into the tire, disengage the bead using the shoe of a tire remover. NOTICE:
|
|
(d) Separate the upper bead.
(e) Take out the tire pressure warning valve and transmitter with the grommet from the tire and separate the lower bead.
(f) Remove the grommet from the tire pressure warning valve and transmitter.
6. REMOVE TIRE PRESSURE WARNING VALVE AND TRANSMITTER (for Type C)
(a) Remove the tire valve cap.
NOTICE:
Keep the removed tire valve cap.
(b) Remove the valve core to release the air from the tire.
NOTICE:
Make sure that a sufficient amount of air has been released.
(c) Using a 11 mm deep socket wrench, remove the nut and washer.
(d) Drop the tire pressure warning valve and transmitter with grommet into the tire.
HINT:
The grommet may remain attached to the rim.
|
(e) Using a tire remover, remove the tire from the disc wheel. NOTICE:
|
|
(f) Take out the tire pressure warning valve and transmitter with grommet from the tire.
(g) Remove the grommet from the tire pressure warning valve and transmitter.
|
(h) Using a T10 "TORX" socket wrench, remove the bolt and tire pressure monitor sensor from the tubeless tire valve. |
|
|
|