Last Modified: 01-30-2024 6.11:8.1.0 Doc ID: RM100000001KKY4
Model Year Start: 2020 Model: RAV4 Prod Date Range: [10/2019 - 12/2021]
Title: TIRE PRESSURE MONITORING: TIRE PRESSURE WARNING SYSTEM: C2121-C2125,C2181-C2185; No Signal from Transmitter ID1; 2020 - 2021 MY RAV4 RAV4 HV [10/2019 - 12/2021]

DTC

C2121

No Signal from Transmitter ID1

DTC

C2122

No Signal from Transmitter ID2

DTC

C2123

No Signal from Transmitter ID3

DTC

C2124

No Signal from Transmitter ID4

DTC

C2125

No Signal from Transmitter ID5

DTC

C2181

Transmitter ID1 not Received (Test Mode DTC)

DTC

C2182

Transmitter ID2 not Received (Test Mode DTC)

DTC

C2183

Transmitter ID3 not Received (Test Mode DTC)

DTC

C2184

Transmitter ID4 not Received (Test Mode DTC)

DTC

C2185

Transmitter ID5 not Received (Test Mode DTC)

DESCRIPTION

The tire pressure warning valve and transmitters that are installed in the tire and wheel assemblies measure the tire pressure of each wheel. The measured values are transmitted to the tire pressure warning ECU and receiver in the vehicle as radio waves. The ECU compares the measured tire pressure values with the tire pressure threshold. When the measured tire pressure value is less than this threshold, the warning light in the combination meter assembly illuminates.

The tire pressure warning valve and transmitters constantly send radio waves to the tire pressure warning ECU and receiver.

Under the conditions below, the tire pressure warning ECU and receiver is unable to receive the signals from the tire pressure warning valve and transmitters, and a DTC is stored.

  • Facilities or devices that use similar radio frequencies are located in the vicinity of the vehicle.
  • Devices using similar radio frequencies are used in the vehicle.
  • The ID of a tire pressure warning valve and transmitter is mistyped during registration.
  • A tire, wheel and/or transmitter from a different vehicle is installed.

HINT:

When no transmitter ID is received from a tire pressure warning valve and transmitter for 20 minutes or more while the vehicle speed is more than 40 km/h (25 mph), or no transmitter ID is received from all of the tire pressure warning valve and transmitters for 20 minutes or more, DTCs from C2121 to C2124 (C2125: w/ Full Size Spare Tire) are stored.

DTCs C2121 to C2124 (C2125: w/ Full Size Spare Tire) can only be cleared by using the Techstream. DTCs C2181 to C2184 (C2185: w/ Full Size Spare Tire) can be cleared when the tire pressure warning valve and transmitter sends a forced transmission signal or test mode ends. DTCs C2181 to C2184 (C2185: w/ Full Size Spare Tire) are output only in test mode.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

Note

C2121

No Signal from Transmitter ID1

Either of the following conditions (a) or (b) is met:

(a) When all conditions below are met:

  • Tire pressure warning valve and transmitter is not in stop mode.
  • Any transmitter ID is not received from tire pressure warning valve and transmitters.
  • Vehicle speed is more than 40 km/h (25 mph) or no vehicle speed signal is received for 20 minutes or more.

(b) When both conditions below are met:

  • Tire pressure warning valve and transmitter is not in stop mode.
  • No transmitter ID is received from tire pressure warning valve and transmitters for 20 minutes or more.
  • Tire pressure warning valve and transmitter
  • Tire pressure warning ECU and receiver

-

C2122

No Signal from Transmitter ID2

Either of the following conditions (a) or (b) is met:

(a) When all conditions below are met:

  • Tire pressure warning valve and transmitter is not in stop mode.
  • Any transmitter ID is not received from tire pressure warning valve and transmitters.
  • Vehicle speed is more than 40 km/h (25 mph) or no vehicle speed signal is received for 20 minutes or more.

(b) When both conditions below are met:

  • Tire pressure warning valve and transmitter is not in stop mode.
  • No transmitter ID is received from tire pressure warning valve and transmitters for 20 minutes or more.
  • Tire pressure warning valve and transmitter
  • Tire pressure warning ECU and receiver

-

C2123

No Signal from Transmitter ID3

Either of the following conditions (a) or (b) is met:

(a) When all conditions below are met:

  • Tire pressure warning valve and transmitter is not in stop mode.
  • Any transmitter ID is not received from tire pressure warning valve and transmitters.
  • Vehicle speed is more than 40 km/h (25 mph) or no vehicle speed signal is received for 20 minutes or more.

(b) When both conditions below are met:

  • Tire pressure warning valve and transmitter is not in stop mode.
  • No transmitter ID is received from tire pressure warning valve and transmitters for 20 minutes or more.
  • Tire pressure warning valve and transmitter
  • Tire pressure warning ECU and receiver

-

C2124

No Signal from Transmitter ID4

Either of the following conditions (a) or (b) is met:

(a) When all conditions below are met:

  • Tire pressure warning valve and transmitter is not in stop mode.
  • Any transmitter ID is not received from tire pressure warning valve and transmitters.
  • Vehicle speed is more than 40 km/h (25 mph) or no vehicle speed signal is received for 20 minutes or more.

(b) When both conditions below are met:

  • Tire pressure warning valve and transmitter is not in stop mode.
  • No transmitter ID is received from tire pressure warning valve and transmitters for 20 minutes or more.
  • Tire pressure warning valve and transmitter
  • Tire pressure warning ECU and receiver

-

C2125

No Signal from Transmitter ID5

Either of the following conditions (a) or (b) is met:

(a) When all conditions below are met:

  • Tire pressure warning valve and transmitter is not in stop mode.
  • Any transmitter ID is not received from tire pressure warning valve and transmitters.
  • Vehicle speed is more than 40 km/h (25 mph) or no vehicle speed signal is received for 20 minutes or more.

(b) When both conditions below are met:

  • Tire pressure warning valve and transmitter is not in stop mode.
  • No transmitter ID is received from tire pressure warning valve and transmitters for 20 minutes or more.
  • Tire pressure warning valve and transmitter
  • Tire pressure warning ECU and receiver

w/ Full Size Spare Tire

C2181

Transmitter ID1 not Received (Test Mode DTC)

Test mode procedure is performed.

  • Tire pressure warning valve and transmitter
  • Tire pressure warning ECU and receiver

-

C2182

Transmitter ID2 not Received (Test Mode DTC)

Test mode procedure is performed.

  • Tire pressure warning valve and transmitter
  • Tire pressure warning ECU and receiver

-

C2183

Transmitter ID3 not Received (Test Mode DTC)

Test mode procedure is performed.

  • Tire pressure warning valve and transmitter
  • Tire pressure warning ECU and receiver

-

C2184

Transmitter ID4 not Received (Test Mode DTC)

Test mode procedure is performed.

  • Tire pressure warning valve and transmitter
  • Tire pressure warning ECU and receiver

-

C2185

Transmitter ID5 not Received (Test Mode DTC)

Test mode procedure is performed.

  • Tire pressure warning valve and transmitter
  • Tire pressure warning ECU and receiver

w/ Full Size Spare Tire

DTC Detection Conditions: C2121

 

Vehicle Condition

Pattern 1

Pattern 2

Pattern 3

Diagnosis Condition

Tire pressure warning valve and transmitter is not in stop mode.

Vehicle speed is more than 40 km/h (25 mph).

-

-

No vehicle speed signal is received.

-

-

Malfunction Status

Any transmitter ID is not received from tire pressure warning valve and transmitters.

-

No transmitter ID is received from tire pressure warning valve and transmitters.

-

-

Detection Time

20 minutes or more

20 minutes or more

20 minutes or more

Number of Trips

-

-

-

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.

DTC Detection Conditions: C2122

 

Vehicle Condition

Pattern 1

Pattern 2

Pattern 3

Diagnosis Condition

Tire pressure warning valve and transmitter is not in stop mode.

Vehicle speed is more than 40 km/h (25 mph).

-

-

No vehicle speed signal is received.

-

-

Malfunction Status

Any transmitter ID is not received from tire pressure warning valve and transmitters.

-

No transmitter ID is received from tire pressure warning valve and transmitters.

-

-

Detection Time

20 minutes or more

20 minutes or more

20 minutes or more

Number of Trips

-

-

-

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.

DTC Detection Conditions: C2123

 

Vehicle Condition

Pattern 1

Pattern 2

Pattern 3

Diagnosis Condition

Tire pressure warning valve and transmitter is not in stop mode.

Vehicle speed is more than 40 km/h (25 mph).

-

-

No vehicle speed signal is received.

-

-

Malfunction Status

Any transmitter ID is not received from tire pressure warning valve and transmitters.

-

No transmitter ID is received from tire pressure warning valve and transmitters.

-

-

Detection Time

20 minutes or more

20 minutes or more

20 minutes or more

Number of Trips

-

-

-

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.

DTC Detection Conditions: C2124

 

Vehicle Condition

Pattern 1

Pattern 2

Pattern 3

Diagnosis Condition

Tire pressure warning valve and transmitter is not in stop mode.

Vehicle speed is more than 40 km/h (25 mph).

-

-

No vehicle speed signal is received.

-

-

Malfunction Status

Any transmitter ID is not received from tire pressure warning valve and transmitters.

-

No transmitter ID is received from tire pressure warning valve and transmitters.

-

-

Detection Time

20 minutes or more

20 minutes or more

20 minutes or more

Number of Trips

-

-

-

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.

DTC Detection Conditions: C2125 (w/ Full Size Spare Tire)

 

Vehicle Condition

Pattern 1

Pattern 2

Pattern 3

Diagnosis Condition

Tire pressure warning valve and transmitter is not in stop mode.

Vehicle speed is more than 40 km/h (25 mph).

-

-

No vehicle speed signal is received.

-

-

Malfunction Status

Any transmitter ID is not received from tire pressure warning valve and transmitters.

-

No transmitter ID is received from tire pressure warning valve and transmitters.

-

-

Detection Time

20 minutes or more

20 minutes or more

20 minutes or more

Number of Trips

-

-

-

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.

NOTICE:

  • w/ ID Switching Function:

    (Main) is displayed on the DTC screen for the DTCs even when the 2nd set of tires is selected.

  • When DTCs C2121 to C2124 (C2125: w/ Full Size Spare Tire) are set, DTC C2179 may be set simultaneously. In such cases, troubleshoot DTCs C2121 to C2124 (C2125: w/ Full Size Spare Tire) first, then troubleshoot DTC C2179.
  • If the Techstream is used to display the Data List for 10 minutes or more, the tire pressure warning ECU stores DTCs C2121 to C2124 (C2125: w/ Full Size Spare Tire). If these DTCs are stored, clear the DTCs using the Techstream.
  • w/o Full Size Spare Tire:

    If any DTC from C2121 to C2124 is output, clear the DTCs or drive the vehicle at 40 km/h (25 mph) for 1 minute or more after repairing the malfunctions.

  • w/ Full Size Spare Tire:

    If any DTC from C2121 to C2125 is output, clear the DTCs after repairing the malfunctions.

HINT:

It is necessary to perform the following procedure to identify the tire pressure warning valve and transmitter that is malfunctioning because it cannot be identified by the output DTC.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

  • When replacing the tire pressure warning ECU and receiver or tire pressure warning valve and transmitter, read the transmitter IDs and number of the transmitters (4 or 5) stored in the old ECU using the Techstream and write them down before removal.
  • It is necessary to perform initialization 2019 - 2021 MY RAV4 RAV4 HV [11/2018 - 12/2021]; TIRE PRESSURE MONITORING: TIRE PRESSURE WARNING SYSTEM: INITIALIZATION after registration 2020 - 2021 MY RAV4 RAV4 HV [10/2019 - 12/2021]; TIRE PRESSURE MONITORING: TIRE PRESSURE WARNING SYSTEM: REGISTRATION of the transmitter IDs into the tire pressure warning ECU and receiver if the ECU and/or one of the valve and transmitters has been replaced.

PROCEDURE

1.

CHECK FREQUENCY RECEIVING CONDITION

(a) Check that the following conditions are not met:

(1) Facilities or devices that use similar radio frequencies are located in the vicinity of the vehicle.

HINT:

If the vehicle is located in an area such as the one described above, the tire pressure warning light may illuminate after blinking for 1 minute due to interfering radio frequencies.

(2) Devices using similar radio frequencies are used in the vehicle.

HINT:

Radio transmissions may be interrupted due to the surroundings or devices installed by the user.

Result

Proceed to

There is no device or facility that uses electrical waves of approximately the same frequency in the vicinity of the vehicle or inside the vehicle.

A

There is a device or facility that uses electrical waves of approximately the same frequency in the vicinity of the vehicle or inside the vehicle.

B

B

GO TO STEP 12

A

2.

CONFIRM OUTPUT DTC

(a) Check the stored DTC.

Result

Proceed to

Any DTCs from C2121 to C2124 (C2125: w/ Full Size Spare Tire) are output (C2181 to C2184 (C2185: w/ Full Size Spare Tire) when in Test Mode)

A

All DTCs from C2121 to C2124 (C2125: w/ Full Size Spare Tire) are output (C2181 to C2184 (C2185: w/ Full Size Spare Tire) when in Test Mode)

B

B

GO TO STEP 7

A

3.

CONFIRM MODEL

(a) Choose the model to be inspected.

Result

Proceed to

w/ Tire Inflation Pressure Display Function

A

w/o Tire Inflation Pressure Display Function

B

B

GO TO STEP 5

A

4.

IDENTIFY TRANSMITTER CORRESPONDING TO DTC (TIRE POSITION)

(a) Turn the ignition switch off.

(b) Connect the Techstream to the DLC3.

(c) Turn the ignition switch to ON.

(d) Turn the Techstream on.

(e) Enter the following menus: Chassis / Tire Pressure Monitor / Data List.

(f) Display the "ID Tire Position" value for each wheel using the Techstream.

(g) Refer to the following chart and check the wheel position of the DTC and transmitter match.

Chassis > Tire Pressure Monitor > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

ID 1 Tire Position

ID1 Tire Position

No Information or FL or FR or RL or RR or Spare or Judging

ID1 tire position is displayed

  • If no tire position information is stored, "No Information" will be displayed.
  • w/ Tire Inflation Pressure Display Function

ID 2 Tire Position

ID2 Tire Position

No Information or FL or FR or RL or RR or Spare or Judging

ID2 tire position is displayed

  • If no tire position information is stored, "No Information" will be displayed.
  • w/ Tire Inflation Pressure Display Function

ID 3 Tire Position

ID3 Tire Position

No Information or FL or FR or RL or RR or Spare or Judging

ID3 tire position is displayed

  • If no tire position information is stored, "No Information" will be displayed.
  • w/ Tire Inflation Pressure Display Function

ID 4 Tire Position

ID4 Tire Position

No Information or FL or FR or RL or RR or Spare or Judging

ID4 tire position is displayed

  • If no tire position information is stored, "No Information" will be displayed.
  • w/ Tire Inflation Pressure Display Function

ID 5 Tire Position

ID5 Tire Position

No Information or FL or FR or RL or RR or Spare or Judging

ID5 tire position is displayed

  • If no tire position information is stored, "No Information" will be displayed.
  • w/ Tire Inflation Pressure Display Function
  • w/ Full Size Spare Tire

HINT:

Refer to the following chart for the Data List items that correspond to the DTCs.

DTC No.

Detection Item

Data List

*: w/ Full Size Spare Tire

C2121

No Signal from Transmitter ID1

ID1 Tire Position

C2181

Transmitter ID 1 not Received (for Test Diagnosis)

C2122

No Signal from Transmitter ID2

ID2 Tire Position

C2182

Transmitter ID 2 not Received (for Test Diagnosis)

C2123

No Signal from Transmitter ID3

ID3 Tire Position

C2183

Transmitter ID 3 not Received (for Test Diagnosis)

C2124

No Signal from Transmitter ID4

ID4 Tire Position

C2184

Transmitter ID 4 not Received (for Test Diagnosis)

C2125*

No Signal from Transmitter ID5

ID5 Tire Position

C2185*

Transmitter ID 5 not Received (for Test Diagnosis)

Chassis > Tire Pressure Monitor > Data List

Tester Display

ID 1 Tire Position

ID 2 Tire Position

ID 3 Tire Position

ID 4 Tire Position

ID 5 Tire Position

NEXT

GO TO STEP 6

5.

IDENTIFY TRANSMITTER CORRESPONDING TO DTC (TIRE POSITION)

(a) Set the tire pressure to the specified value.

Click here 2020 MY RAV4 RAV4 HV [10/2019 - 08/2020]; TIRE / WHEEL: TIRE AND WHEEL SYSTEM: INSPECTION 2021 - 2024 MY RAV4 RAV4 HV [08/2020 -        ]; TIRE / WHEEL: TIRE AND WHEEL SYSTEM: INSPECTION

(b) Turn the ignition switch off.

(c) Connect the Techstream to the DLC3.

(d) Turn the ignition switch to ON.

(e) Turn the Techstream on.

(f) Enter the following menus: Chassis / Tire Pressure Monitor / Data List.

(g) Display the "ID Tire Inflation Pressure" value for each wheel using the Techstream.

Chassis > Tire Pressure Monitor > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

ID 1 Tire Inflation Pressure

ID1 tire inflation pressure

min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)

max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi)

Actual tire inflation pressure

If N/A is displayed, data has not been received.*1

ID 2 Tire Inflation Pressure

ID2 tire inflation pressure

min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)

max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi)

Actual tire inflation pressure

If N/A is displayed, data has not been received.*1

ID 3 Tire Inflation Pressure

ID3 tire inflation pressure

min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge)/ 0 kPa (0 kgf/cm2, 0 psi)

max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi)

Actual tire inflation pressure

If N/A is displayed, data has not been received.*1

ID 4 Tire Inflation Pressure

ID4 tire inflation pressure

min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)

max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi)

Actual tire inflation pressure

If N/A is displayed, data has not been received.*1

ID 5 Tire Inflation Pressure

ID5 tire inflation pressure

min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)

max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi)

Actual tire inflation pressure

  • If N/A is displayed, data has not been received.*1
  • *2

HINT:

  • *1: It may take a few minutes until the values are displayed.
  • *2: w/ Full Size Spare Tire

Chassis > Tire Pressure Monitor > Data List

Tester Display

ID 1 Tire Inflation Pressure

ID 2 Tire Inflation Pressure

ID 3 Tire Inflation Pressure

ID 4 Tire Inflation Pressure

ID 5 Tire Inflation Pressure

(h) Rapidly reduce the tire pressure for each wheel at least 40 kPa (0.4 kg/cm2, 5.8 psi) within 30 seconds. If the "ID Tire Inflation Pressure" value displayed on the Techstream does not change, the tire pressure warning valve and transmitter corresponding to the unchanged "ID Tire Inflation Pressure" value was the cause of the output DTC.

HINT:

  • Identify the malfunctioning tire pressure warning valve and transmitter by repeatedly decreasing the tire pressure for each tire.
  • Record which "ID Tire Inflation Pressure" value corresponds to each tire.

(i) Check the Data List.

NOTICE:

  • It may take a few minutes until the values are displayed.
  • When an "ID Tire Inflation Pressure" value has not changed, reset the tire pressure to the appropriate specified value and rotate the tire 90 to 270 degrees. Then rapidly release the tire pressure and recheck the value.
  • Record the transmitter IDs and positions of transmitters that are normal.

(j) After confirming that the "ID Tire Inflation Pressure" value for one tire has changed, repeat this procedure for each tire. Identify the transmitter that corresponds to the DTC.

NEXT

6.

CHECK TRANSMITTER ID

(a) Turn the ignition switch off.

(b) Connect the Techstream to the DLC3.

(c) Turn the ignition switch to ON.

(d) Turn the Techstream on.

(e) Enter the following menus: Chassis / Tire Pressure Monitor / Data List.

(f) Refer to the following chart and record the tire pressure warning valve and transmitter ID of the output DTC.

Chassis > Tire Pressure Monitor > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Registered ID 1 Code

Registered ID1 code

min.: 0

max.: FFFFFFF*1

ID No. registered for transmitter ID1 displayed

-

Registered ID 2 Code

Registered ID2 code

min.: 0

max.: FFFFFFF*1

ID No. registered for transmitter ID2 displayed

-

Registered ID 3 Code

Registered ID3 code

min.: 0

max.: FFFFFFF*1

ID No. registered for transmitter ID3 displayed

-

Registered ID 4 Code

Registered ID4 code

min.: 0

max.: FFFFFFF*1

ID No. registered for transmitter ID4 displayed

-

Registered ID 5 Code

Registered ID5 code

min.: 0

max.: FFFFFFF*1

ID No. registered for transmitter ID5 displayed

*2

HINT:

  • *1: Displayed only when the ID No. is not registered.
  • *2: w/ Full Size Spare Tire
  • Refer to the following chart for the Data List items that correspond to the DTCs.

    DTC No.

    Detection Item

    Data List

    *: w/ Full Size Spare Tire

    C2121

    No Signal from Transmitter ID1

    Registered ID 1 code

    C2181

    Transmitter ID 1 not Received (for Test Diagnosis)

    C2122

    No Signal from Transmitter ID2

    Registered ID 2 code

    C2182

    Transmitter ID 2 not Received (for Test Diagnosis)

    C2123

    No Signal from Transmitter ID3

    Registered ID 3 code

    C2183

    Transmitter ID 3 not Received (for Test Diagnosis)

    C2124

    No Signal from Transmitter ID4

    Registered ID 4 code

    C2184

    Transmitter ID 4 not Received (for Test Diagnosis)

    C2125*

    No Signal from Transmitter ID5

    Registered ID 5 code

    C2185*

    Transmitter ID 5 not Received (for Test Diagnosis)

Chassis > Tire Pressure Monitor > Data List

Tester Display

Registered ID 1 Code

Registered ID 2 Code

Registered ID 3 Code

Registered ID 4 Code

Registered ID 5 Code

(g) Disassemble the tire indicated in the output DTC and check the tire pressure warning valve and transmitter ID.

*A

for Type A

-

-

*1

Tire Pressure Warning Valve and Transmitter

-

-

*a

Transmitter ID (7-digit Number)

-

-

*A

for Type B

-

-

*1

Tire Pressure Warning Valve and Transmitter

-

-

*a

Transmitter ID (7-digit Number)

*b

Wheel Speed Type Tire Inflation Pressure Display Function Identification Mark

NOTICE:

For vehicles equipped with the wheel speed type tire inflation pressure display function, be sure to use tire pressure warning valve and transmitters with identification marks.

*A

for Type C

-

-

*1

Tire Pressure Warning Valve and Transmitter

-

-

*a

Transmitter ID (7-digit Number)

-

-

*A

for Type D

-

-

*1

Tire Pressure Warning Valve and Transmitter

-

-

*a

Transmitter ID (7-digit Number)

-

-

(h) Confirm that the ID number on the transmitter and recorded transmitter ID match.

Result

Proceed to

Match

A

Do not match

B

A

REPLACE CORRESPONDING TIRE PRESSURE WARNING VALVE AND TRANSMITTER

B

GO TO STEP 9

7.

TEST MODE INSPECTION (C2181 to C2184 (C2185: w/ Full Size Spare Tire))

(a) Perform a test mode inspection and perform Transmitter Data Reception Check (C2181 to C2184 (C2185: w/ Full Size Spare Tire)).

Click here 2019 - 2021 MY RAV4 RAV4 HV [11/2018 - 12/2021]; TIRE PRESSURE MONITORING: TIRE PRESSURE WARNING SYSTEM: TEST MODE PROCEDURE

OK

END

Explain to the customer that there is a high possibility that a DTC was output due to temporary electrical wave interference.

NG

8.

CHECK TIRE PRESSURE WARNING VALVE AND TRANSMITTER

(a) Turn the ignition switch off.

(b) Connect the Techstream to the DLC3.

(c) Turn the ignition switch to ON.

(d) Turn the Techstream on.

(e) Enter the following menus: Chassis / Tire Pressure Monitor / Data List.

(f) Refer to the following chart and record all of the tire pressure warning valve and transmitter IDs.

Chassis > Tire Pressure Monitor > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Registered ID 1 Code

Registered ID1 code

min.: 0

max.: FFFFFFF*1

ID No. registered for transmitter ID1 displayed

-

Registered ID 2 Code

Registered ID2 code

min.: 0

max.: FFFFFFF*1

ID No. registered for transmitter ID2 displayed

-

Registered ID 3 Code

Registered ID3 code

min.: 0

max.: FFFFFFF*1

ID No. registered for transmitter ID3 displayed

-

Registered ID 4 Code

Registered ID4 code

min.: 0

max.: FFFFFFF*1

ID No. registered for transmitter ID4 displayed

-

Registered ID 5 Code

Registered ID5 code

min.: 0

max.: FFFFFFF*1

ID No. registered for transmitter ID5 displayed

*2

HINT:

  • *1: Displayed only when the ID No. is not registered.
  • *2: w/ Full Size Spare Tire
  • The wheel position cannot be determined from ID1 through ID5 on the Data List.

Chassis > Tire Pressure Monitor > Data List

Tester Display

Registered ID 1 Code

Registered ID 2 Code

Registered ID 3 Code

Registered ID 4 Code

Registered ID 5 Code

(g) Disassemble all of the tires and check the tire pressure warning valve and transmitter IDs.

*A

for Type A

-

-

*1

Tire Pressure Warning Valve and Transmitter

-

-

*a

Transmitter ID (7-digit Number)

-

-

*A

for Type B

-

-

*1

Tire Pressure Warning Valve and Transmitter

-

-

*a

Transmitter ID (7-digit Number)

*b

Wheel Speed Type Tire Inflation Pressure Display Function Identification Mark

NOTICE:

For vehicles equipped with the wheel speed type tire inflation pressure display function, be sure to use tire pressure warning valve and transmitters with identification marks.

*A

for Type C

-

-

*1

Tire Pressure Warning Valve and Transmitter

-

-

*a

Transmitter ID (7-digit Number)

-

-

*A

for Type D

-

-

*1

Tire Pressure Warning Valve and Transmitter

-

-

*a

Transmitter ID (7-digit Number)

-

-

(h) Confirm that the ID number on the transmitter and recorded transmitter ID match.

Result

Proceed to

Match

A

Do not match

B

A

REPLACE TIRE PRESSURE WARNING ECU AND RECEIVER

B

9.

REGISTRATION OF TRANSMITTER ID

(a) Perform registration.

Click here 2020 - 2021 MY RAV4 RAV4 HV [10/2019 - 12/2021]; TIRE PRESSURE MONITORING: TIRE PRESSURE WARNING SYSTEM: REGISTRATION

NEXT

10.

PERFORM INITIALIZATION

(a) Perform initialization.

Click here 2019 - 2021 MY RAV4 RAV4 HV [11/2018 - 12/2021]; TIRE PRESSURE MONITORING: TIRE PRESSURE WARNING SYSTEM: INITIALIZATION

NEXT

11.

CLEAR DTC

(a) Clear the DTCs.

Chassis > Tire Pressure Monitor > Clear DTCs

NEXT

END

12.

CLEAR DTC

(a) Clear the DTCs.

Chassis > Tire Pressure Monitor > Clear DTCs

NEXT

END

Explain to the customer that there is a high possibility that a device (located near or inside the vehicle) or facility using electrical waves of approximately the same frequency is causing electrical wave interference.