Last Modified: 01-30-2024 6.11:8.1.0 Doc ID: RM100000001KGAD
Model Year Start: 2020 Model: RAV4 Prod Date Range: [10/2019 - 10/2022]
Title: AUDIO / VIDEO: AUDIO AND VISUAL SYSTEM: Speaker Circuit; 2020 - 2022 MY RAV4 RAV4 HV [10/2019 - 10/2022]

Speaker Circuit

DESCRIPTION

for 9 Speakers:

If there is a short in a speaker circuit, the stereo component amplifier assembly detects it and stops output to the speakers.

As a result, sound cannot be heard from the speakers even if there is no malfunction in the stereo component amplifier assembly, DCM (telematics transceiver) or speakers.

for 6 Speakers:

If there is a short in a speaker circuit, the radio and display receiver assembly detects it and stops output to the speakers.

As a result, sound cannot be heard from the speakers even if there is no malfunction in the radio and display receiver assembly, DCM (telematics transceiver)* or speakers.

  • *: w/ Manual (SOS) Switch

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

  • When replacing the radio and display receiver assembly, always replace it with a new one. If a radio and display receiver assembly which was installed to another vehicle is used, the following may occur:
    • A communication malfunction DTC is stored.
    • The radio and display receiver assembly may not operate normally.
  • When replacing the DCM (telematics transceiver), make sure to replace it with a new one (w/ Manual [SOS] Switch).
  • Before replacing the DCM (telematics transceiver), refer to Registration.

    for HV Model: Click here 2020 - 2021 MY RAV4 HV [10/2019 - 12/2021]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function, HV Model): REGISTRATION 2022 - 2024 MY RAV4 HV [12/2021 -        ]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function, HV Model): REGISTRATION

    for Gasoline Model: Click here 2020 MY RAV4 [10/2019 - 08/2020]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function, Gasoline Model): REGISTRATION 2021 MY RAV4 [08/2020 - 12/2021]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function, Gasoline Model): REGISTRATION 2022 - 2024 MY RAV4 [12/2021 -        ]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function, Gasoline Model): REGISTRATION

HINT:

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Audio and Visual System.

Click here 2020 - 2022 MY RAV4 RAV4 HV [10/2019 - 10/2022]; AUDIO / VIDEO: AUDIO AND VISUAL SYSTEM: PRECAUTION

PROCEDURE

1.

CHECK MODEL

(a) Choose the model to be inspected.

Result

Proceed to

for 6 Speakers

A

for 9 Speakers

B

B

GO TO STEP 12

A

2.

CHECK SPEAKER (OPERATION CHECK)

(a) Enter the "System Check Mode" screen. Refer to Check Speaker in Operation Check.

Click here 2020 - 2022 MY RAV4 RAV4 HV [10/2019 - 10/2022]; AUDIO / VIDEO: AUDIO AND VISUAL SYSTEM: OPERATION CHECK

(b) Perform the operation check above and determine the speaker that is not operating.

Not Operating Speaker

Proceed to

Front No. 1 speaker assembly or front No. 2 speaker assembly

A

Rear speaker assembly

B

HINT:

If sound cannot be heard from any speaker, inspect all of them.

B

GO TO STEP 10

A

3.

CHECK MODEL

(a) Choose the model to be inspected.

Result

Proceed to

w/ Manual (SOS) Switch

A

w/o Manual (SOS) Switch

B

B

GO TO STEP 7

A

4.

CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - FRONT NO. 1 SPEAKER ASSEMBLY - FRONT NO. 2 SPEAKER ASSEMBLY - DCM [TELEMATICS TRANSCEIVER])

(a) Disconnect the G4 radio and display receiver assembly connector.

(b) Disconnect the I1 and J1 front No. 1 speaker assembly connectors.

(c) Disconnect the G5 and G6 front No. 2 speaker assembly connectors.

(d) Disconnect the G133 DCM (telematics transceiver) connector.

(e) Measure the resistance according to the value (s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

G4-1 (FR+) - G133-1 (SPI+)

Always

Below 1 Ω

G4-6 (FR-) - G133-2 (SPI-)

Always

Below 1 Ω

G133-3 (SPO+) - G5-4 (TWR+)

Always

Below 1 Ω

G133-4 (SPO-) - G5-2 (TWR-)

Always

Below 1 Ω

G4-2 (FL+) - G6-4 (TWL+)

Always

Below 1 Ω

G4-7 (FL-) - G6-2 (TWL-)

Always

Below 1 Ω

I1-2 (+) - G5-3 (+)

Always

Below 1 Ω

I1-1 (-) - G5-1 (-)

Always

Below 1 Ω

J1-2 (+) - G6-3 (+)

Always

Below 1 Ω

J1-1 (-) - G6-1 (-)

Always

Below 1 Ω

G4-1 (FR+) - Body ground

Always

10 kΩ or higher

G4-6 (FR-) - Body ground

Always

10 kΩ or higher

G133-3 (SPO+) - Body ground

Always

10 kΩ or higher

G133-4 (SPO-) - Body ground

Always

10 kΩ or higher

G4-2 (FL+) - Body ground

Always

10 kΩ or higher

G4-7 (FL-) - Body ground

Always

10 kΩ or higher

I1-2 (+) - Body ground

Always

10 kΩ or higher

I1-1 (-) - Body ground

Always

10 kΩ or higher

J1-2 (+) - Body ground

Always

10 kΩ or higher

J1-1 (-) - Body ground

Always

10 kΩ or higher

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

5.

INSPECT FRONT NO. 1 SPEAKER ASSEMBLY

(a) Remove the front No. 1 speaker assembly.

Click here 2019 - 2024 MY RAV4 RAV4 HV [11/2018 -        ]; AUDIO / VIDEO: FRONT DOOR SPEAKER: REMOVAL

(b) Inspect the front No. 1 speaker assembly.

Click here 2019 - 2024 MY RAV4 RAV4 HV [11/2018 -        ]; AUDIO / VIDEO: FRONT DOOR SPEAKER: INSPECTION

NG

REPLACE FRONT NO. 1 SPEAKER ASSEMBLY

OK

6.

INSPECT DCM (TELEMATICS TRANSCEIVER)

(a) Remove the DCM (telematics transceiver).

Click here 2020 - 2022 MY RAV4 RAV4 HV [10/2019 - 10/2022]; CELLULAR COMMUNICATION: DCM(TELEMATICS TRANSCEIVER): REMOVAL

*a

Component without harness connected

(DCM [Telematics Transceiver])

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

1 (SPI+) - 3 (SPO+)

Always

Below 1 Ω

2 (SPI-) - 4 (SPO-)

Always

Below 1 Ω

1 (SPI+) - 2 (SPI-)

Always

10 kΩ or higher

3 (SPO+) - 4 (SPO-)

Always

10 kΩ or higher

1 (SPI+) - Body ground

Always

10 kΩ or higher

2 (SPI-) - Body ground

Always

10 kΩ or higher

OK

GO TO STEP 9

NG

REPLACE DCM (TELEMATICS TRANSCEIVER)

7.

CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - FRONT NO. 1 SPEAKER ASSEMBLY - FRONT NO. 2 SPEAKER ASSEMBLY)

(a) Disconnect the G4 radio and display receiver assembly connector.

(b) Disconnect the I1 and J1 front No. 1 speaker assembly connectors.

(c) Disconnect the G5 and G6 front No. 2 speaker assembly connectors.

(d) Measure the resistance according to the value (s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

G4-1 (FR+) - G5-4 (TWR+)

Always

Below 1 Ω

G4-6 (FR-) - G5-2 (TWR-)

Always

Below 1 Ω

G4-2 (FL+) - G6-4 (TWL+)

Always

Below 1 Ω

G4-7 (FL-) - G6-2 (TWL-)

Always

Below 1 Ω

I1-2 (+) - G5-3 (+)

Always

Below 1 Ω

I1-1 (-) - G5-1 (-)

Always

Below 1 Ω

J1-2 (+) - G6-3 (+)

Always

Below 1 Ω

J1-1 (-) - G6-1 (-)

Always

Below 1 Ω

G4-1 (FR+) - Body ground

Always

10 kΩ or higher

G4-6 (FR-) - Body ground

Always

10 kΩ or higher

G4-2 (FL+) - Body ground

Always

10 kΩ or higher

G4-7 (FL-) - Body ground

Always

10 kΩ or higher

I1-2 (+) - Body ground

Always

10 kΩ or higher

I1-1 (-) - Body ground

Always

10 kΩ or higher

J1-2 (+) - Body ground

Always

10 kΩ or higher

J1-1 (-) - Body ground

Always

10 kΩ or higher

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

8.

INSPECT FRONT NO. 1 SPEAKER ASSEMBLY

(a) Remove the front No. 1 speaker assembly.

Click here 2019 - 2024 MY RAV4 RAV4 HV [11/2018 -        ]; AUDIO / VIDEO: FRONT DOOR SPEAKER: REMOVAL

(b) Inspect the front No. 1 speaker assembly.

Click here 2019 - 2024 MY RAV4 RAV4 HV [11/2018 -        ]; AUDIO / VIDEO: FRONT DOOR SPEAKER: INSPECTION

NG

REPLACE FRONT NO. 1 SPEAKER ASSEMBLY

OK

9.

REPLACE FRONT NO. 2 SPEAKER ASSEMBLY

(a) Replace the front No. 2 speaker assembly with a new or known good one.

Click here 2019 - 2024 MY RAV4 RAV4 HV [11/2018 -        ]; AUDIO / VIDEO: INSTRUMENT PANEL SPEAKER: REMOVAL

(b) Check the malfunction disappears.

OK:

Malfunction disappears.

HINT:

  • Connect all the connectors to the front No. 2 speaker assemblies that were disconnected.
  • When there is a possibility that either the right or left front speaker is defective, inspect by interchanging the right one with the left one.
  • Perform the above inspection on both the LH and RH sides.
OK

END (FRONT NO. 2 SPEAKER ASSEMBLY IS DEFECTIVE)

NG

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

10.

CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - REAR SPEAKER ASSEMBLY)

(a) Disconnect the G4 radio and display receiver assembly connector.

(b) Disconnect the K1 and L1 rear speaker assembly connectors.

(c) Measure the resistance according to the value (s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

G4-4 (RR+) - K1-2 (+)

Always

Below 1 Ω

G4-9 (RR-) - K1-1 (-)

Always

Below 1 Ω

G4-3 (RL+) - L1-2 (+)

Always

Below 1 Ω

G4-8 (RL-) - L1-1 (-)

Always

Below 1 Ω

G4-4 (RR+) - Body ground

Always

10 kΩ or higher

G4-9 (RR-) - Body ground

Always

10 kΩ or higher

G4-3 (RL+) - Body ground

Always

10 kΩ or higher

G4-8 (RL-) - Body ground

Always

10 kΩ or higher

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

11.

INSPECT REAR SPEAKER ASSEMBLY

(a) Remove the rear speaker assembly.

Click here 2019 - 2024 MY RAV4 RAV4 HV [11/2018 -        ]; AUDIO / VIDEO: REAR DOOR SPEAKER: REMOVAL

(b) Inspect the rear speaker assembly.

Click here 2019 - 2024 MY RAV4 RAV4 HV [11/2018 -        ]; AUDIO / VIDEO: REAR DOOR SPEAKER: INSPECTION

OK:

Malfunction disappears.

OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPLACE REAR SPEAKER ASSEMBLY

12.

CHECK SPEAKER (OPERATION CHECK)

(a) Enter the "System Check Mode" screen. Refer to Check Speaker in Operation Check.

Click here 2020 - 2022 MY RAV4 RAV4 HV [10/2019 - 10/2022]; AUDIO / VIDEO: AUDIO AND VISUAL SYSTEM: OPERATION CHECK

(b) Perform the operation check above and determine the speaker that is not operating.

Not Operating Speaker

Proceed to

Front No. 1 speaker assembly or front No. 3 speaker assembly

A

Front No. 2 speaker assembly

B

Rear speaker assembly

C

Rear No. 2 speaker assembly

D

HINT:

If sound cannot be heard from any speaker, inspect all of them.

B

GO TO STEP 16

C

GO TO STEP 19

D

GO TO STEP 21

A

13.

CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - FRONT NO. 3 SPEAKER ASSEMBLY - FRONT NO. 1 SPEAKER ASSEMBLY)

(a) Disconnect the M2 stereo component amplifier assembly connector.

(b) Disconnect the J1 and I1 front No. 1 speaker assembly connectors.

(c) Disconnect the G6 and G5 front No. 3 speaker assembly connectors.

(d) Measure the resistance according to the value (s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

M2-9 (FR+) - G5-4 (TWR+)

Always

Below 1 Ω

M2-24 (FR-) - G5-2 (TWR-)

Always

Below 1 Ω

M2-14 (FL+) - G6-4 (TWL+)

Always

Below 1 Ω

M2-29 (FL-) - G6-2 (TWL-)

Always

Below 1 Ω

J1-2 (+) - G6-3 (+)

Always

Below 1 Ω

J1-1 (-) - G6-1 (-)

Always

Below 1 Ω

I1-2 (+) - G5-3 (+)

Always

Below 1 Ω

I1-1 (-) - G5-1 (-)

Always

Below 1 Ω

M2-9 (FR+) - Body ground

Always

10 kΩ or higher

M2-24 (FR-) - Body ground

Always

10 kΩ or higher

M2-14 (FL+) - Body ground

Always

10 kΩ or higher

M2-29 (FL-) - Body ground

Always

10 kΩ or higher

G6-3 (+) - Body ground

Always

10 kΩ or higher

G6-1 (-) - Body ground

Always

10 kΩ or higher

G5-3 (+) - Body ground

Always

10 kΩ or higher

G5-1 (-) - Body ground

Always

10 kΩ or higher

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

14.

INSPECT FRONT NO. 3 SPEAKER ASSEMBLY

(a) Remove the front No. 3 speaker assembly.

Click here 2019 - 2024 MY RAV4 RAV4 HV [11/2018 -        ]; AUDIO / VIDEO: PILLAR SPEAKER: REMOVAL

(b) Inspect the front No. 3 speaker assembly.

Click here 2019 - 2024 MY RAV4 RAV4 HV [11/2018 -        ]; AUDIO / VIDEO: PILLAR SPEAKER: INSPECTION

NG

REPLACE FRONT NO. 3 SPEAKER ASSEMBLY

OK

15.

INSPECT FRONT NO. 1 SPEAKER ASSEMBLY

(a) Remove the front No. 1 speaker assembly.

Click here 2019 - 2024 MY RAV4 RAV4 HV [11/2018 -        ]; AUDIO / VIDEO: FRONT DOOR SPEAKER: REMOVAL

(b) Inspect the front No. 1 speaker assembly.

Click here 2019 - 2024 MY RAV4 RAV4 HV [11/2018 -        ]; AUDIO / VIDEO: FRONT DOOR SPEAKER: INSPECTION

OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPLACE FRONT NO. 1 SPEAKER ASSEMBLY

16.

CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - DCM (TELEMATICS TRANSCEIVER) - FRONT NO. 2 SPEAKER ASSEMBLY)

(a) Disconnect the M2 stereo component amplifier assembly connector.

(b) Disconnect the G7 and G8 front No. 2 speaker assembly connectors.

(c) Disconnect the G133 DCM (telematics transceiver) connector.

(d) Measure the resistance according to the value (s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

M2-10 (TWL+) - G8-1 (+)

Always

Below 1 Ω

M2-25 (TWL-) - G8-2 (-)

Always

Below 1 Ω

M2-13 (TWR+) - G133-1 (SPI+)

Always

Below 1 Ω

M2-28 (TWR-) - G133-2 (SPI-)

Always

Below 1 Ω

G133-3 (SPO+) - G7-1 (+)

Always

Below 1 Ω

G133-4 (SPO-) - G7-2 (-)

Always

Below 1 Ω

M2-10 (TWL+) - Body ground

Always

10 kΩ or higher

M2-25 (TWL-) - Body ground

Always

10 kΩ or higher

M2-13 (TWR+) - Body ground

Always

10 kΩ or higher

M2-28 (TWR-) - Body ground

Always

10 kΩ or higher

G133-3 (SPO+) - Body ground

Always

10 kΩ or higher

G133-4 (SPO-) - Body ground

Always

10 kΩ or higher

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

17.

INSPECT DCM (TELEMATICS TRANSCEIVER)

(a) Remove the DCM (telematics transceiver).

Click here 2020 - 2022 MY RAV4 RAV4 HV [10/2019 - 10/2022]; CELLULAR COMMUNICATION: DCM(TELEMATICS TRANSCEIVER): REMOVAL

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

1 (SPI+) - 3 (SPO+)

Always

Below 1 Ω

2 (SPI-) - 4 (SPO-)

Always

Below 1 Ω

1 (SPI+) - 2 (SPI-)

Always

10 kΩ or higher

3 (SPO+) - 4 (SPO-)

Always

10 kΩ or higher

1 (SPI+) - Body ground

Always

10 kΩ or higher

2 (SPI-) - Body ground

Always

10 kΩ or higher

*a

Component without harness connected

(DCM [Telematics Transceiver])

NG

REPLACE DCM (TELEMATICS TRANSCEIVER)

OK

18.

INSPECT FRONT NO. 2 SPEAKER ASSEMBLY

(a) Remove the front No. 2 speaker assembly.

Click here 2019 - 2024 MY RAV4 RAV4 HV [11/2018 -        ]; AUDIO / VIDEO: INSTRUMENT PANEL SPEAKER: REMOVAL

(b) Inspect the front No. 2 speaker assembly.

Click here 2019 - 2024 MY RAV4 RAV4 HV [11/2018 -        ]; AUDIO / VIDEO: INSTRUMENT PANEL SPEAKER: INSPECTION

OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPLACE FRONT NO. 2 SPEAKER ASSEMBLY

19.

CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - REAR SPEAKER ASSEMBLY)

(a) Disconnect the M2 stereo component amplifier assembly connector.

(b) Disconnect the L1 and K1 rear speaker assembly connectors.

(c) Measure the resistance according to the value (s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

M2-12 (RR+) - K1-2 (+)

Always

Below 1 Ω

M2-27 (RR-) - K1-1 (-)

Always

Below 1 Ω

M2-11 (RL+) - L1-2 (+)

Always

Below 1 Ω

M2-26 (RL-) - L1-1 (-)

Always

Below 1 Ω

M2-12 (RR+) - Body ground

Always

10 kΩ or higher

M2-27 (RR-) - Body ground

Always

10 kΩ or higher

M2-11 (RL+) - Body ground

Always

10 kΩ or higher

M2-26 (RL-) - Body ground

Always

10 kΩ or higher

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

20.

REPLACE REAR SPEAKER ASSEMBLY

(a) Remove the rear speaker assembly.

Click here 2019 - 2024 MY RAV4 RAV4 HV [11/2018 -        ]; AUDIO / VIDEO: REAR DOOR SPEAKER: REMOVAL

(b) Inspect the rear speaker assembly.

Click here 2019 - 2024 MY RAV4 RAV4 HV [11/2018 -        ]; AUDIO / VIDEO: REAR DOOR SPEAKER: INSPECTION

OK:

Malfunction disappears.

OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPLACE REAR SPEAKER ASSEMBLY

21.

CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - REAR NO. 2 SPEAKER ASSEMBLY)

(a) Disconnect the M2 stereo component amplifier assembly connector.

(b) Disconnect the N1 rear No. 2 speaker assembly connector.

(c) Measure the resistance according to the value (s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

M2-15 (WFR+) - N1-4 (WF+)

Always

Below 1 Ω

M2-23 (WFL-) - N1-3 (WF-)

Always

Below 1 Ω

M2-8 (WFL+) - N1-2 (WF+)

Always

Below 1 Ω

M2-30 (WFR-) - N1-1 (WF-)

Always

Below 1 Ω

M2-15 (WFR+) - Body ground

Always

10 kΩ or higher

M2-23 (WFL-) - Body ground

Always

10 kΩ or higher

M2-8 (WFL+) - Body ground

Always

10 kΩ or higher

M2-30 (WFR-) - Body ground

Always

10 kΩ or higher

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

22.

REPLACE REAR NO. 2 SPEAKER ASSEMBLY

(a) Remove the No. 2 rear speaker assembly.

Click here 2019 - 2024 MY RAV4 RAV4 HV [11/2018 -        ]; AUDIO / VIDEO: REAR DOOR SPEAKER: REMOVAL

(b) Inspect the No. 2 rear speaker assembly.

Click here 2019 - 2024 MY RAV4 RAV4 HV [11/2018 -        ]; AUDIO / VIDEO: REAR DOOR SPEAKER: INSPECTION

OK:

Malfunction disappears.

OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPLACE REAR NO. 2 SPEAKER ASSEMBLY