Last Modified: 01-30-2024 6.11:8.1.0 Doc ID: RM100000001HK2D
Model Year Start: 2019 Model: RAV4 HV Prod Date Range: [02/2019 -           ]
Title: THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Entry Function, HV Model): TERMINALS OF ECU; 2019 - 2024 MY RAV4 HV [02/2019 -        ]

TERMINALS OF ECU

CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

(a) Disconnect the G54 certification ECU (smart key ECU assembly) connector.

(b) Measure the voltage and resistance according to the value(s) in the table below.

Tester Connection

Wiring Color

Input/Output

Terminal Description

Condition

Specified Condition

Related Data List Item

G54-18 (E) - Body ground

W-B - Body ground

-

Ground

Always

Below 1 Ω

-

G54-4 (+B) - G54-18 (E)

P - W-B

Input

Power supply

Power switch off

11 to 14 V

-

G54-15 (CUTB) - G54-18 (E)

V - W-B

Input

Dark current cut pin*

Power switch off

11 to 14 V

-

  • *: In order to prevent the vehicle auxiliary battery from being depleted when the vehicle is shipped long distances, a fuse that cuts unnecessary electrical load while the vehicle is being shipped is installed in the circuit. If the fuse is removed, the circuit becomes open. If the fuse that is between the vehicle auxiliary battery and terminal CUTB is removed and the circuit is open, the certification ECU (smart key ECU assembly) changes to a certain control mode (example: the transmission of radio waves every 0.25 seconds, which form the detection area, stops).

(c) Reconnect the G54 certification ECU (smart key ECU assembly) connector.

(d) Measure the voltage and check for pulses according to the value(s) in the table below.

Tester Connection

Wiring Color

Input/Output

Terminal Description

Condition

Specified Condition

Related Data List Item

G54-17 (IG1D) - G54-18 (E)

L - W-B

Output

IG power supply

Power switch off → on (IG)

1 V or less → 9 V or higher

Power Source Control

  • IG Relay Monitor (Outside)

G54-16 (ACCD) - G54-18 (E)

G - W-B

Output

ACC power supply

Power switch off → on (ACC)

1 V or less → 8.5 V or higher

Power Source Control

  • ACC Relay Monitor

M7-17 (CLG1) - G54-18 (E)

R - W-B

Output

Output to driver door electrical key antenna

(request signal (challenge) is sent to door electrical key antenna from certification ECU (smart key ECU assembly) to form detection area)

Procedure:

  1. Power switch off
  2. All doors closed
  3. Electrical key transmitter sub-assembly not inside vehicle
  4. All doors locked through wireless operation

    (electrical key transmitter sub-assembly brought inside detection area*2)

Pulse generation

(See waveform 1)

-

Procedure:

  1. Power switch off
  2. All doors closed
  3. Electrical key transmitter sub-assembly not inside vehicle
  4. All doors locked through wireless operation

    (electrical key transmitter sub-assembly brought outside detection area*2)

Pulse generation

(See waveform 2)

M7-17 (CLG1) - G54-18 (E)

R - W-B

Input

Input to driver door lock sensor

(front door outside handle assembly LH lock sensor ON signal is sent to the certification ECU (smart key ECU assembly))

Procedure:

  1. Power switch off
  2. Electrical key transmitter sub-assembly brought outside vehicle
  3. All doors closed
  4. All doors locked through wireless operation

    (electrical key transmitter sub-assembly brought outside detection area*2)

  5. Driver door lock sensor touched

Pulse generation

(See waveform 3)

Smart Key

  • D-Door Trigger Switch

M7-17 (CLG1) - G54-18 (E)

R - W-B

Input

Input to driver door unlock sensor

(when system is in unlock standby mode and unlock sensor is touched, door electrical key antenna sends unlock sensor input signal (sensing) to certification ECU (smart key ECU assembly))

Procedure:

  1. Power switch off
  2. Electrical key transmitter sub-assembly brought outside vehicle
  3. All doors locked
  4. Electrical key transmitter sub-assembly not near the vehicle
  5. Driver door unlock sensor touched

Pulse generation

(See waveform 4)

Smart Key

  • D-Door Touch Sensor

M7-16 (CG1B) - G54-18 (E)

GR- W-B

Output

Output to driver door electrical key antenna (terminal on opposite side of component from CLG1 output terminal)

Procedure:

  1. Power switch off
  2. All doors closed
  3. Electrical key transmitter sub-assembly not inside vehicle
  4. All doors locked through wireless operation

    (electrical key transmitter sub-assembly brought inside detection area*2)

Pulse generation

(See waveform 5)

-

Procedure:

  1. Power switch off
  2. All doors closed
  3. Electrical key transmitter sub-assembly not inside vehicle
  4. All doors locked through wireless operation

    (electrical key transmitter sub-assembly brought outside detection area*2)

Pulse generation

(See waveform 6)

M7-15 (CLG2) - G54-18 (E)

R - W-B

Output

Output to front passenger door electrical key antenna

(request signal (challenge) is sent to door electrical key antenna from certification ECU (smart key ECU assembly) to form detection area)

Procedure:

  1. Power switch off
  2. All doors closed
  3. Electrical key transmitter sub-assembly not inside vehicle
  4. All doors locked through wireless operation

    (electrical key transmitter sub-assembly brought inside detection area*2)

Pulse generation

(See waveform 1)

-

Procedure:

  1. Power switch off
  2. All doors closed
  3. Electrical key transmitter sub-assembly not inside vehicle
  4. All doors locked through wireless operation

    (electrical key transmitter sub-assembly brought outside detection area*2)

Pulse generation

(See waveform 2)

M7-15 (CLG2) - G54-18 (E)

R - W-B

Input

Input to front passenger door lock sensor

(front door outside handle assembly RH lock sensor ON signal is sent to the certification ECU (smart key ECU assembly))

Procedure:

  1. Power switch off
  2. Electrical key transmitter sub-assembly brought outside vehicle
  3. All doors closed
  4. All doors locked through wireless operation

    (electrical key transmitter sub-assembly brought outside detection area*2)

  5. Front passenger door lock sensor touched

Pulse generation

(See waveform 3)

Smart Key

  • P-Door Touch Sensor

M7-15 (CLG2) - G54-18 (E)

R - W-B

Input

Input to front passenger door unlock sensor

(when system is in unlock standby mode and unlock sensor is touched, door electrical key antenna sends unlock sensor input signal (sensing) to certification ECU (smart key ECU assembly))

Procedure:

  1. Power switch off
  2. Electrical key transmitter sub-assembly brought outside vehicle
  3. All doors locked
  4. Electrical key transmitter sub-assembly not near the vehicle
  5. Front passenger door unlock sensor touched

Pulse generation

(See waveform 4)

Smart Key

  • P-Door Touch Sensor

M7-14 (CG2B) - G54-18 (E)

W - W-B

Output

Output to front passenger door electrical key antenna (terminal on opposite side of component from CLG2 output terminal)

Procedure:

  1. Power switch off
  2. All doors closed
  3. Electrical key transmitter sub-assembly not inside vehicle
  4. All doors locked through wireless operation

    (electrical key transmitter sub-assembly brought inside detection area*2)

Pulse generation

(See waveform 5)

-

Procedure:

  1. Power switch off
  2. All doors closed
  3. Electrical key transmitter sub-assembly not inside vehicle
  4. All doors locked through wireless operation

    (electrical key transmitter sub-assembly brought outside detection area*2)

Pulse generation

(See waveform 6)

M7-1 (CLG3) - G54-18 (E)*1

Output

BE - W-B

Output to rear door electrical key antenna LH

(request signal (challenge) is sent to door electrical key antenna from certification ECU (smart key ECU assembly) to form detection area)

Procedure:

  1. Power switch off
  2. All doors closed
  3. Electrical key transmitter sub-assembly not inside vehicle
  4. All doors locked through wireless operation

    (electrical key transmitter sub-assembly brought inside detection area*2)

Pulse generation

(See waveform 1)

-

Procedure:

  1. Power switch off
  2. All doors closed
  3. Electrical key transmitter sub-assembly not inside vehicle
  4. All doors locked through wireless operation

    (electrical key transmitter sub-assembly brought outside detection area*2)

Pulse generation

(See waveform 2)

M7-1 (CLG3) - G54-18 (E)*1

Input

BE - W-B

Input to rear door lock sensor LH

(rear door outside handle assembly LH lock sensor ON signal is sent to the certification ECU (smart key ECU assembly))

Procedure:

  1. Power switch off
  2. Electrical key transmitter sub-assembly brought outside vehicle
  3. All doors closed
  4. All doors locked through wireless operation

    (electrical key transmitter sub-assembly brought outside detection area*2)

  5. Rear door LH lock sensor touched

Pulse generation

(See waveform 3)

Smart Key

  • Dr-Door Touch Sensor

M7-1 (CLG3) - G54-18 (E)*1

Input

BE - W-B

Input to rear door unlock sensor LH

(when system is in unlock standby mode and unlock sensor is touched, door electrical key antenna sends unlock sensor input signal (sensing) to certification ECU (smart key ECU assembly))

Procedure:

  1. Power switch off
  2. Electrical key transmitter sub-assembly brought outside vehicle
  3. All doors locked
  4. Electrical key transmitter sub-assembly not near the vehicle
  5. Rear door LH unlock sensor touched

Pulse generation

(See waveform 4)

Smart Key

  • Dr-Door Touch Sensor

M7-2 (CG3B) - G54-18 (E)*1

Output

GR - W-B

Output to rear door LH electrical key antenna (terminal on opposite side of component from CLG3 output terminal)

Procedure:

  1. Power switch off
  2. All doors closed
  3. Electrical key transmitter sub-assembly not inside vehicle
  4. All doors locked through wireless operation

    (electrical key transmitter sub-assembly brought inside detection area*2)

Pulse generation

(See waveform 5)

-

Procedure:

  1. Power switch off
  2. All doors closed
  3. Electrical key transmitter sub-assembly not inside vehicle
  4. All doors locked through wireless operation

    (electrical key transmitter sub-assembly brought outside detection area*2)

Pulse generation

(See waveform 6)

M7-9 (CLG4) - G54-18 (E)*1

Output

L - W-B

Output to rear door electrical key antenna RH

(request signal (challenge) is sent to door electrical key antenna from certification ECU (smart key ECU assembly) to form detection area)

Procedure:

  1. Power switch off
  2. All doors closed
  3. Electrical key transmitter sub-assembly not inside vehicle
  4. All doors locked through wireless operation

    (electrical key transmitter sub-assembly brought inside detection area*2)

Pulse generation

(See waveform 1)

-

Procedure:

  1. Power switch off
  2. All doors closed
  3. Electrical key transmitter sub-assembly not inside vehicle
  4. All doors locked through wireless operation

    (electrical key transmitter sub-assembly brought outside detection area*2)

Pulse generation

(See waveform 2)

M7-9 (CLG4) - G54-18 (E)*1

Input

L - W-B

Input to rear door lock sensor RH

(rear door outside handle assembly RH lock sensor ON signal is sent to the certification ECU (smart key ECU assembly))

Procedure:

  1. Power switch off
  2. Electrical key transmitter sub-assembly brought outside vehicle
  3. All doors closed
  4. All doors locked through wireless operation

    (electrical key transmitter sub-assembly brought outside detection area*2)

  5. Rear door RH lock sensor touched

Pulse generation

(See waveform 3)

Smart Key

  • Pr-Door Trigger Switch

M7-9 (CLG4) - G54-18 (E)*1

Input

L - W-B

Input to rear door unlock sensor RH

(when system is in unlock standby mode and unlock sensor is touched, door electrical key antenna sends unlock sensor input signal (sensing) to certification ECU (smart key ECU assembly))

Procedure:

  1. Power switch off
  2. Electrical key transmitter sub-assembly brought outside vehicle
  3. All doors locked
  4. Electrical key transmitter sub-assembly not near the vehicle
  5. Rear door RH unlock sensor touched

Pulse generation

(See waveform 4)

Smart Key

  • Pr-Door Touch Sensor

M7-8 (CG4B) - G54-18 (E)*1

Output

GR - W-B

Output to rear door RH electrical key antenna (terminal on opposite side of component from CLG4 output terminal)

Procedure:

  1. Power switch off
  2. All doors closed
  3. Electrical key transmitter sub-assembly not inside vehicle
  4. All doors locked through wireless operation

    (electrical key transmitter sub-assembly brought inside detection area*2)

Pulse generation

(See waveform 5)

-

Procedure:

  1. Power switch off
  2. All doors closed
  3. Electrical key transmitter sub-assembly not inside vehicle
  4. All doors locked through wireless operation

    (electrical key transmitter sub-assembly brought outside detection area*2)

Pulse generation

(See waveform 6)

M7-13 (CLG8) - G54-18 (E)

R - W-B

Output

Output to electrical key antenna (outside luggage compartment)

Procedure:

  1. Power switch off
  2. Electrical key transmitter sub-assembly brought outside vehicle
  3. All doors closed
  4. Back door opener switch assembly off → on

Pulse generation

(See waveform 7)

-

M7-12 (CG8B) - G54-18 (E)

L - W-B

Output

Output to electrical key antenna (outside luggage compartment) (terminal on opposite side of component from CLG8 output terminal)

Procedure:

  1. Power switch off
  2. Electrical key transmitter sub-assembly brought outside vehicle
  3. All doors closed
  4. Back door opener switch assembly off → on

Pulse generation

(See waveform 7)

-

M7-26 (TSW5) - G54-18 (E)

B - W-B

Input

Back door opener switch assembly (unlock switch) signal input

Back door opener switch assembly (unlock switch) off → on

Pulse generation

(See waveform 8)

Smart Key

  • Tr/B-Door Unlock SW

M7-27 (TSW6) - G54-18 (E)

R - W-B

Input

Back door opener switch assembly (lock switch) signal input

Back door opener switch assembly (lock switch) off → on

Pulse generation

(See waveform 8)

Smart Key

  • Tr/B-Door Unlock SW

M7-18 (RCO) - G54-18 (E)

L - W-B

Output

Output to door control receiver

(Power supply for door control receiver. Certification ECU (smart key ECU assembly) outputs 5 V when receiver starts operating.)

Procedure:

  1. Power switch off
  2. Electrical key transmitter sub-assembly brought outside detection area but kept inside wireless function operational area
  3. Lock or unlock switch of electrical key transmitter sub-assembly not pressed → pressed

Pulse generation

(See waveform 9)

-

M7-19 (RDAM) - G54-18 (E)

G - W-B

Input

Door control receiver verifies data received from electrical key transmitter sub-assembly.

Door control receiver sends data from electrical key transmitter sub-assembly to certification ECU (smart key ECU assembly) (Door control receiver intermittently grounds 12 V signal from certification ECU (smart key ECU assembly)).

Procedure:

  1. Power switch off
  2. All doors locked
  3. Electrical key transmitter sub-assembly not inside vehicle
  4. Electrical key transmitter sub-assembly brought outside detection area but kept inside wireless function operational area
  5. Lock or unlock switch of electrical key transmitter sub-assembly not pressed → pressed

Pulse generation

(See waveform 10)

-

M7-20 (CSEL) - G54-18 (E)

BE - W-B

Output

Communication channel switching circuit

Procedure:

  1. Power switch off
  2. All doors closed

Pulse generation

-

  • *1: w/ Rear Door Entry
  • *2: For details about the entry function detection area, refer to Operation Check.

    Click here 2019 - 2023 MY RAV4 HV [02/2019 - 10/2023]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Entry Function, HV Model): OPERATION CHECK 2024 MY RAV4 HV [10/2023 -        ]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Entry Function, HV Model): OPERATION CHECK

(e) Using an oscilloscope, check the waveform of the ECU.

NOTICE:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.

(1) Waveform 1

Item

Content

Tester Connection

M7-17 (CLG1) - G54-18 (E)

M7-15 (CLG2) - G54-18 (E)

M7-1 (CLG3) - G54-18 (E)*1

M7-9 (CLG4) - G54-18 (E)*1

Tool Setting

5 V/DIV., 500 ms/DIV.

Condition

Procedure:

  1. Power switch off
  2. All doors closed
  3. Electrical key transmitter sub-assembly not inside vehicle
  4. All doors locked through wireless operation

    (electrical key transmitter sub-assembly brought inside detection area*2)

  • *1: w/ Rear Door Entry
  • *2: For details about the entry function detection area, refer to Operation Check.

    Click here 2019 - 2023 MY RAV4 HV [02/2019 - 10/2023]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Entry Function, HV Model): OPERATION CHECK 2024 MY RAV4 HV [10/2023 -        ]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Entry Function, HV Model): OPERATION CHECK

(2) Waveform 2

Item

Content

Tester Connection

M7-17 (CLG1) - G54-18 (E)

M7-15 (CLG2) - G54-18 (E)

M7-1 (CLG3) - G54-18 (E)*1

M7-9 (CLG4) - G54-18 (E)*1

Tool Setting

5 V/DIV., 100 ms/DIV.

Condition

Procedure:

  1. Power switch off
  2. All doors closed
  3. Electrical key transmitter sub-assembly not inside vehicle
  4. All doors locked through wireless operation

    (electrical key transmitter sub-assembly brought outside detection area*2)

  • *1: w/ Rear Door Entry
  • *2: For details about the entry function detection area, refer to Operation Check.

    Click here 2019 - 2023 MY RAV4 HV [02/2019 - 10/2023]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Entry Function, HV Model): OPERATION CHECK 2024 MY RAV4 HV [10/2023 -        ]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Entry Function, HV Model): OPERATION CHECK

(3) Waveform 3

*a

Lock sensor not touched

*b

Lock sensor touched

Front Door Outside Handle Assembly LH

Item

Content

Tester Connection

M7-17 (CLG1) - G54-18 (E)

Tool Setting

5 V/DIV., 40 ms/DIV.

Condition

Procedure:

  1. Power switch off
  2. Electrical key transmitter sub-assembly brought outside vehicle
  3. All doors closed
  4. All doors locked through wireless operation

    (electrical key transmitter sub-assembly brought outside detection area*2)

  5. Driver door lock sensor touched

Front Door Outside Handle Assembly RH

Item

Content

Tester Connection

M7-15 (CLG2) - G54-18 (E)

Tool Setting

5 V/DIV., 40 ms/DIV.

Condition

Procedure:

  1. Power switch off
  2. Electrical key transmitter sub-assembly brought outside vehicle
  3. All doors closed
  4. All doors locked through wireless operation

    (electrical key transmitter sub-assembly brought outside detection area*)

  5. Front passenger door lock sensor touched

Rear Door Outside Handle Assembly LH (w/ Rear Door Entry)

Item

Content

Tester Connection

M7-1 (CLG3) - G54-18 (E)

Tool Setting

5 V/DIV., 40 ms/DIV.

Condition

Procedure:

  1. Power switch off
  2. Electrical key transmitter sub-assembly brought outside vehicle
  3. All doors closed
  4. All doors locked through wireless operation

    (electrical key transmitter sub-assembly brought outside detection area*)

  5. Rear door LH lock sensor touched

Rear Door Outside Handle Assembly RH (w/ Rear Door Entry)

Item

Content

Tester Connection

M7-9 (CLG4) - G54-18 (E)

Tool Setting

5 V/DIV., 40 ms/DIV.

Condition

Procedure:

  1. Power switch off
  2. Electrical key transmitter sub-assembly brought outside vehicle
  3. All doors closed
  4. All doors locked through wireless operation

    (electrical key transmitter sub-assembly brought outside detection area*)

  5. Rear door RH lock sensor touched
  • *: For details about the entry function detection area, refer to Operation Check.

    Click here 2019 - 2023 MY RAV4 HV [02/2019 - 10/2023]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Entry Function, HV Model): OPERATION CHECK 2024 MY RAV4 HV [10/2023 -        ]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Entry Function, HV Model): OPERATION CHECK

(4) Waveform 4

Front Door Outside Handle Assembly LH

Item

Content

Tester Connection

M7-17 (CLG1) - G54-18 (E)

Tool Setting

5 V/DIV., 50 ms/DIV.

Condition

Procedure:

  1. Power switch off
  2. Electrical key transmitter sub-assembly brought outside vehicle
  3. All doors locked
  4. Electrical key transmitter sub-assembly not near the vehicle
  5. Driver door unlock sensor touched

*a

Unlock sensor not touched

*b

Unlock sensor touched

Front Door Outside Handle Assembly RH

Item

Content

Tester Connection

M7-15 (CLG2) - G54-18 (E)

Tool Setting

5 V/DIV., 50 ms/DIV.

Condition

Procedure:

  1. Power switch off
  2. Electrical key transmitter sub-assembly brought outside vehicle
  3. All doors locked
  4. Electrical key transmitter sub-assembly not near the vehicle
  5. Front passenger door unlock sensor touched

Rear Door Outside Handle Assembly LH (w/ Rear Door Entry)

Item

Content

Tester Connection

M7-1 (CLG3) - G54-18 (E)

Tool Setting

5 V/DIV., 50 ms/DIV.

Condition

Procedure:

  1. Power switch off
  2. Electrical key transmitter sub-assembly brought outside vehicle
  3. All doors locked
  4. Electrical key transmitter sub-assembly not near the vehicle
  5. Rear door LH unlock sensor touched

Rear Door Outside Handle Assembly RH (w/ Rear Door Entry)

Item

Content

Tester Connection

M7-9 (CLG4) - G54-18 (E)

Tool Setting

5 V/DIV., 50 ms/DIV.

Condition

Procedure:

  1. Power switch off
  2. Electrical key transmitter sub-assembly brought outside vehicle
  3. All doors locked
  4. Electrical key transmitter sub-assembly not near the vehicle
  5. Rear door RH unlock sensor touched

(5) Waveform 5

Item

Content

Tester Connection

M7-16 (CG1B) - G54-18 (E)

M7-14 (CG2B) - G54-18 (E)

M7-2 (CG3B) - G54-18 (E)*1

M7-8 (CG4B) - G54-18 (E)*1

Tool Setting

5 V/DIV., 500 ms/DIV.

Condition

Procedure:

  1. Power switch off
  2. All doors closed
  3. Electrical key transmitter sub-assembly not inside vehicle
  4. All doors locked through wireless operation

    (electrical key transmitter sub-assembly brought inside detection area*2)

  • *1: w/ Rear Door Entry
  • *2: For details about the entry function detection area, refer to Operation Check.

    Click here 2019 - 2023 MY RAV4 HV [02/2019 - 10/2023]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Entry Function, HV Model): OPERATION CHECK 2024 MY RAV4 HV [10/2023 -        ]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Entry Function, HV Model): OPERATION CHECK

(6) Waveform 6

Item

Content

Tester Connection

M7-16 (CG1B) - G54-18 (E)

M7-14 (CG2B) - G54-18 (E)

M7-2 (CG3B) - G54-18 (E)*1

M7-8 (CG4B) - G54-18 (E)*1

Tool Setting

5 V/DIV., 100 ms/DIV.

Condition

Procedure:

  1. Power switch off
  2. All doors closed
  3. Electrical key transmitter sub-assembly not inside vehicle
  4. All doors locked through wireless operation

    (electrical key transmitter sub-assembly brought outside detection area*2)

  • *1: w/ Rear Door Entry
  • *2: For details about the entry function detection area, refer to Operation Check.

    Click here 2019 - 2023 MY RAV4 HV [02/2019 - 10/2023]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Entry Function, HV Model): OPERATION CHECK 2024 MY RAV4 HV [10/2023 -        ]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Entry Function, HV Model): OPERATION CHECK

(7) Waveform 7

Item

Content

Tester Connection

M7-13 (CLG8) - G54-18 (E)

M7-12 (CG8B) - G54-18 (E)

Tool Setting

2 V/DIV., 500 ms/DIV.

Condition

Procedure:

  1. Power switch off
  2. Electrical key transmitter sub-assembly brought outside vehicle
  3. All doors closed
  4. Back door opener switch assembly off → on

(8) Waveform 8

Item

Content

Tester Connection

M7-26 (TSW5) - G54-18 (E)

Tool Setting

2 V/DIV., 500 ms/DIV.

Condition

Back door opener switch assembly (unlock switch) off → on

*a

Checking for switch ON signal at short intervals

Item

Content

Tester Connection

M7-27 (TSW6) - G54-18 (E)

Tool Setting

2 V/DIV., 500 ms/DIV.

Condition

Back door opener switch assembly (lock switch) off → on

(9) Waveform 9

Item

Content

Tester Connection

M7-18 (RCO) - G54-18 (E)

Tool Setting

2 V/DIV., 500 ms/DIV.

Condition

Procedure:

  1. Power switch off
  2. Electrical key transmitter sub-assembly brought outside detection area but kept inside wireless function operational area
  3. Lock or unlock switch of electrical key transmitter sub-assembly not pressed → pressed

*a

Before lock or unlock switch of electrical key transmitter sub-assembly pressed

*b

After lock or unlock switch of electrical key transmitter sub-assembly pressed

(10) Waveform 10

Item

Content

Tester Connection

M7-19 (RDAM) - G54-18 (E)

Tool Setting

5 V/DIV., 500 ms/DIV.

Condition

Procedure:

  1. Power switch off
  2. All doors locked
  3. Electrical key transmitter sub-assembly not inside vehicle
  4. Electrical key transmitter sub-assembly brought outside detection area but kept inside wireless function operational area
  5. Lock or unlock switch of electrical key transmitter sub-assembly not pressed → pressed

*a

Before lock or unlock switch of electrical key transmitter sub-assembly pressed

*b

After lock or unlock switch of electrical key transmitter sub-assembly pressed

*1

Main body ECU (multiplex network body ECU)

-

-

CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

(a) Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

Click here 2019 MY RAV4 RAV4 HV [02/2019 - 10/2019]; POWER DISTRIBUTION: MAIN BODY ECU: REMOVAL 2020 MY RAV4 RAV4 HV [10/2019 - 08/2020]; POWER DISTRIBUTION: MAIN BODY ECU: REMOVAL 2021 MY RAV4 RAV4 HV [08/2020 - 12/2021]; POWER DISTRIBUTION: MAIN BODY ECU: REMOVAL 2022 MY RAV4 RAV4 HV [12/2021 - 10/2022]; POWER DISTRIBUTION: MAIN BODY ECU: REMOVAL 2023 MY RAV4 RAV4 HV [10/2022 - 10/2023]; POWER DISTRIBUTION: MAIN BODY ECU: REMOVAL 2024 MY RAV4 RAV4 HV [10/2023 -        ]; POWER DISTRIBUTION: MAIN BODY ECU: REMOVAL

(b) Measure the voltage and resistance according to the value(s) in the table below.

Tester Connection

Wiring Color

Input/Output

Terminal Description

Condition

Specified Condition

A-11 (GND1) - Body ground

-

-

Ground

Always

Below 1 Ω

A-31 (BECU) - Body ground

-

Input

Auxiliary battery power supply

Power switch off

11 to 14 V