Last Modified: 01-30-2024 |
6.11:8.1.0 |
Doc ID: RM100000001HK1X |
Model Year Start: 2019 |
Model: RAV4 HV |
Prod Date Range: [02/2019 -
] |
Title: THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Entry Function, HV Model): B27A4; Open in Rear Door Electrical Antenna Circuit, Front Passengers Side; 2019 - 2024 MY RAV4 HV [02/2019 - ] |
DTC
|
B27A4
|
Open in Rear Door Electrical Antenna Circuit, Front Passengers Side
|
DESCRIPTION
The certification ECU (smart key ECU assembly) generates a request signal and transmits the signal to the rear door outside handle assembly RH (electrical key antenna) at intervals of 0.25 seconds. For the rear door outside handle assembly RH (electrical key antenna) to detect when the electrical key transmitter sub-assembly is brought close to the vehicle, a signal requesting a response from the electrical key transmitter sub-assembly is transmitted within approximately 1 m (3.28 ft.) of the rear door at intervals of 0.25 seconds. DTC B27A4 is stored by the certification ECU (smart key ECU assembly) when an open circuit is detected between the certification ECU (smart key ECU assembly) and rear door outside handle assembly RH (electrical key antenna) (between terminals CLG4 and ANT1, or terminals CG4B and ANT2).
DTC No.
|
Detection Item
|
DTC Detection Condition
|
Trouble Area
|
Note
|
B27A4
|
Open in Rear Door Electrical Antenna Circuit, Front Passengers Side
|
An open circuit is detected in the circuit between the certification ECU (smart key ECU assembly) and rear door outside handle assembly RH (CLG4 - ANT1, CG4B - ANT2) (This is detected by the malfunction detection circuit in the certification ECU (smart key ECU assembly)) (1 trip detection logic*).
|
-
Certification ECU (smart key ECU assembly)
-
Rear door outside handle assembly RH
-
Harness or connector
|
DTC Output Confirmation Operation:
|
-
*: Only output while a malfunction is present.
Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected
|
Fail-safe Operation when Malfunction Detected
|
Entry lock/unlock operation cannot be performed for rear door RH
|
-
|
Related Data List and Active Test
DTC Code
|
Data List and Active Test
|
B27A4
|
Key diagnostic mode can be used to perform troubleshooting
|
WIRING DIAGRAM
CAUTION / NOTICE / HINT
PROCEDURE
1.
|
CHECK CONNECTOR CONNECTION
|
(a) Check that the connectors are properly connected to the certification ECU (smart key ECU assembly) and rear door outside handle assembly RH.
OK:
Connectors are properly connected.
NG |
|
CONNECT CONNECTORS PROPERLY
|
OK
|
|
|
2.
|
CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - REAR DOOR OUTSIDE HANDLE ASSEMBLY RH)
|
(a) Disconnect the M7 certification ECU (smart key ECU assembly) connector.
(b) Disconnect the K6 rear door outside handle assembly RH connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
M7-9 (CLG4) - K6-6 (ANT1)
|
Always
|
Below 1 Ω
|
M7-8 (CG4B) - K6-4 (ANT2)
|
Always
|
Below 1 Ω
|
(d) Reconnect the M7 certification ECU (smart key ECU assembly) connector.
NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR
|
OK
|
|
|
3.
|
CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO REAR DOOR OUTSIDE HANDLE ASSEMBLY RH)
|
*a
|
Component with harness connected
(Certification ECU (Smart Key ECU Assembly))
|
*b
|
Waveform 1
|
*c
|
Waveform 2
|
*d
|
Waveform 3
|
*e
|
Waveform 4
|
-
|
-
|
(a) Using an oscilloscope, check the waveform.
OK:
Tester Connection
|
Condition
|
Tool Setting
|
Specified Condition
|
M7-9 (CLG4) - G54-18 (E)
|
Procedure:
-
Power switch off
-
All doors closed
-
Electrical key transmitter sub-assembly not inside vehicle
-
All doors locked through wireless operation
(electrical key transmitter sub-assembly brought inside detection area*)
|
5 V/DIV., 500 ms/DIV.
|
Pulse generation
(See waveform 1)
|
Procedure:
-
Power switch off
-
All doors closed
-
Electrical key transmitter sub-assembly not inside vehicle
-
All doors locked through wireless operation
(electrical key transmitter sub-assembly brought outside detection area*)
|
5 V/DIV., 100 ms/DIV.
|
Pulse generation
(See waveform 2)
|
M7-8 (CG4B) - G54-18 (E)
|
Procedure:
-
Power switch off
-
All doors closed
-
Electrical key transmitter sub-assembly not inside vehicle
-
All doors locked through wireless operation
(electrical key transmitter sub-assembly brought inside detection area*)
|
5 V/DIV., 500 ms/DIV.
|
Pulse generation
(See waveform 3)
|
Procedure:
-
Power switch off
-
All doors closed
-
Electrical key transmitter sub-assembly not inside vehicle
-
All doors locked through wireless operation
(electrical key transmitter sub-assembly brought outside detection area*)
|
5 V/DIV., 100 ms/DIV.
|
Pulse generation
(See waveform 4)
|
-
*: For details about the entry function detection area, refer to Operation Check.
Click here
|