| Last Modified: 01-30-2024 | 6.11:8.1.0 | Doc ID: RM100000001HH5V |
| Model Year Start: 2019 | Model: RAV4 | Prod Date Range: [02/2019 - 08/2020] |
| Title: METER / GAUGE / DISPLAY: METER / GAUGE SYSTEM: Fuel Receiver Gauge Display Malfunction; 2019 - 2020 MY RAV4 RAV4 HV [02/2019 - 08/2020] | ||
|
Fuel Receiver Gauge Display Malfunction |
DESCRIPTION
for Gasoline Model:
- The combination meter assembly uses the fuel sender gauge assembly and No. 2 fuel sender gauge assembly to detect the amount of fuel remaining in the fuel tank assembly. The Hall IC built into the fuel sender gauge assembly and No. 2 fuel sender gauge assembly changes the output voltage according to the amount of fuel remaining. The combination meter assembly receives fuel injection volume signals from the ECM and detects the voltage output from the fuel sender gauge assembly and No. 2 fuel sender gauge assembly and operates the fuel receiver gauge.
for HV Model:
- The combination meter assembly uses the fuel sender gauge assembly to detect the amount of fuel remaining in the fuel tank assembly. The Hall IC built into the fuel sender gauge assembly changes the output voltage according to the amount of fuel remaining. The combination meter assembly receives fuel injection volume signals from the ECM and detects the voltage output from the fuel sender gauge assembly and operates the fuel receiver gauge.
WIRING DIAGRAM
for Gasoline Model:
for HV Model:
CAUTION / NOTICE / HINT
CAUTION:
Be careful of flames.
NOTICE:
When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.
PROCEDURE
|
1. |
CHECK FOR DTC |
(a) Check if DTCs are output.
Click here
![2019 - 2024 MY RAV4 RAV4 HV [11/2018 - ]; METER / GAUGE / DISPLAY: METER / GAUGE SYSTEM: DTC CHECK / CLEAR](/t3Portal/stylegraphics/info.gif)
Body Electrical > Combination Meter > Trouble Codes
OK:
DTCs are not output.
| NG |
|
|
|
2. |
CHECK FOR DTC (SFI SYSTEM) |
(a) Check if SFI system DTCs are output.
for A25A-FKS with Canister Pump Module:
Click here
for A25A-FKS without Canister Pump Module:
Click here
for A25A-FXS with Canister Pump Module:
Click here
for A25A-FXS without Canister Pump Module:
Click here
Powertrain > Engine > Trouble Codes
| NG |
|
GO TO SFI SYSTEM for A25A-FKS with Canister Pump Module: Click here
for A25A-FKS without Canister Pump Module: Click here
for A25A-FXS with Canister Pump Module: Click here
for A25A-FXS without Canister Pump Module: Click here
|
|
|
3. |
PERFORM ACTIVE TEST USING TECHSTREAM |
(a) Using the Techstream, perform the Active Test.
Click here
Body Electrical > Combination Meter > Active Test
|
Tester Display |
Measurement Item |
Control Range |
|---|---|---|
|
Fuel Gauge Operation (Sender E) |
Fuel receiver gauge (Sender E) |
ON |
|
Fuel Gauge Operation (Empty) |
Fuel receiver gauge (Empty) |
ON |
|
Fuel Gauge Operation (Warning) |
Fuel receiver gauge (Warning) |
ON |
|
Fuel Gauge Operation (1/4) |
Fuel receiver gauge (1/4) |
ON |
|
Fuel Gauge Operation (1/2) |
Fuel receiver gauge (1/2) |
ON |
|
Fuel Gauge Operation (3/4) |
Fuel receiver gauge (3/4) |
ON |
|
Fuel Gauge Operation (Full) |
Fuel receiver gauge (Full) |
ON |
|
Fuel Gauge Operation (Sender F) |
Fuel receiver gauge (Sender F) |
ON |
Body Electrical > Combination Meter > Active Test
|
Tester Display |
|---|
|
Fuel Gauge Operation (Sender E) |
Body Electrical > Combination Meter > Active Test
|
Tester Display |
|---|
|
Fuel Gauge Operation (Empty) |
Body Electrical > Combination Meter > Active Test
|
Tester Display |
|---|
|
Fuel Gauge Operation (Warning) |
Body Electrical > Combination Meter > Active Test
|
Tester Display |
|---|
|
Fuel Gauge Operation (1/4) |
Body Electrical > Combination Meter > Active Test
|
Tester Display |
|---|
|
Fuel Gauge Operation (1/2) |
Body Electrical > Combination Meter > Active Test
|
Tester Display |
|---|
|
Fuel Gauge Operation (3/4) |
Body Electrical > Combination Meter > Active Test
|
Tester Display |
|---|
|
Fuel Gauge Operation (Full) |
Body Electrical > Combination Meter > Active Test
|
Tester Display |
|---|
|
Fuel Gauge Operation (Sender F) |
OK:
Fuel receiver gauge indication is normal.
4.2 Inch Model:
|
*a |
Fuel Gauge Operation (Sender E) |
|
*b |
Fuel Gauge Operation (Empty) |
|
*c |
Fuel Gauge Operation (Warning) |
|
*d |
Fuel Gauge Operation (1/4) |
|
*e |
Fuel Gauge Operation (1/2) |
|
*f |
Fuel Gauge Operation (3/4) |
|
*g |
Fuel Gauge Operation (Full) |
|
*h |
Fuel Gauge Operation (Sender F) |
7 Inch Model:
|
*a |
Fuel Gauge Operation (Sender E) |
|
*b |
Fuel Gauge Operation (Empty) |
|
*c |
Fuel Gauge Operation (Warning) |
|
*d |
Fuel Gauge Operation (1/4) |
|
*e |
Fuel Gauge Operation (1/2) |
|
*f |
Fuel Gauge Operation (3/4) |
|
*g |
Fuel Gauge Operation (Full) |
|
*h |
Fuel Gauge Operation (Sender F) |
Result |
Proceed to |
|---|---|
|
OK (for Gasoline Model) |
A |
|
OK (for HV Model) |
B |
|
NG |
C |
| B |
|
| C |
|
|
|
4. |
CHECK HARNESS AND CONNECTOR (FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY - COMBINATION METER ASSEMBLY) |
(a) Disconnect the G18 combination meter assembly connector.
(b) Disconnect the N27 fuel suction with pump and gauge tube assembly connector.
(c) Disconnect the M18 No. 2 fuel sender gauge assembly connector.
(d) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
N27-3 (FS) - G18-31(FR) |
Always |
Below 1 Ω |
|
N27-2 (FE) - G18-24 (FE&B) |
Always |
Below 1 Ω |
|
N27-1 (FV) - G18-14 (FV) |
Always |
Below 1 Ω |
|
M18-3 (FR) - G18-13 (FR2) |
Always |
Below 1 Ω |
|
M18-2 (FE) - G18-24 (FE&B) |
Always |
Below 1 Ω |
|
M18-1 (FV) - G18-14 (FV) |
Always |
Below 1 Ω |
|
N27-3 (FS) or G18-31(FR) - Other terminals and body ground |
Always |
10 kΩ or higher |
|
N27-2 (FE) or G18-24 (FE&B) - Other terminals and body ground |
Always |
10 kΩ or higher |
|
N27-1 (FV) or G18-14 (FV) - Other terminals and body ground |
Always |
10 kΩ or higher |
|
M18-3 (FR) or G18-13 (FR2) - Other terminals and body ground |
Always |
10 kΩ or higher |
|
M18-2 (FE) or G18-24 (FE&B) - Other terminals and body ground |
Always |
10 kΩ or higher |
|
M18-1 (FV) or G18-14 (FV) - Other terminals and body ground |
Always |
10 kΩ or higher |
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
5. |
INSPECT FUEL SENDER GAUGE ASSEMBLY |
(a) Remove the fuel sender gauge assembly.
w/ Canister Pump Module:
Click here
w/o Canister Pump Module:
Click here
(b) Inspect the fuel sender gauge assembly.
w/ Canister Pump Module:
Click here
w/o Canister Pump Module:
Click here
| NG |
|
REPLACE FUEL SENDER GAUGE ASSEMBLY w/ Canister Pump Module: Click here
w/o Canister Pump Module: Click here
|
|
|
6. |
INSPECT FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY |
|
*a |
Component without harness connected (Fuel Suction With Pump and Gauge Tube Assembly) |
(a) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
N27-1 (FV) - A-3 |
Always |
Below 1 Ω |
|
N27-2 (FE) - A-2 |
Always |
Below 1 Ω |
|
N27-3 (FS) - A-1 |
Always |
Below 1 Ω |
| NG |
|
REPLACE FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY w/ Canister Pump Module: Click here
w/o Canister Pump Module: Click here
|
|
|
7. |
INSPECT NO. 2 FUEL SENDER GAUGE ASSEMBLY |
(a) Remove the No. 2 fuel sender gauge assembly.
w/ Canister Pump Module:
Click here
w/o Canister Pump Module:
Click here
(b) Inspect the No. 2 fuel sender gauge assembly.
w/ Canister Pump Module:
Click here
w/o Canister Pump Module:
Click here
| OK |
|
CLEAN INSIDE OF FUEL TANK ASSEMBLY |
| NG |
|
REPLACE NO. 2 FUEL SENDER GAUGE ASSEMBLY w/ Canister Pump Module: Click here
w/o Canister Pump Module: Click here
|
|
8. |
CHECK HARNESS AND CONNECTOR (FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY - COMBINATION METER ASSEMBLY) |
(a) Disconnect the N47 fuel suction with pump and gauge tube assembly connector.
(b) Disconnect the G18 combination meter assembly connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
N47-3 (FS) - G18-31(FR) |
Always |
Below 1 Ω |
|
N47-2 (FE) - G18-24 (FE&B) |
Always |
Below 1 Ω |
|
N47-1 (FV) - G18-14 (FV) |
Always |
Below 1 Ω |
|
N47-3 (FS) or G18-31(FR) - Other terminals and body ground |
Always |
10 kΩ or higher |
|
N47-2 (FE) or G18-24 (FE&B) - Other terminals and body ground |
Always |
10 kΩ or higher |
|
N47-1 (FV) or G18-14 (FV) - Other terminals and body ground |
Always |
10 kΩ or higher |
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
9. |
INSPECT FUEL SENDER GAUGE ASSEMBLY |
(a) Remove the fuel sender gauge assembly.
w/ Canister Pump Module:
Click here
w/o Canister Pump Module:
Click here
(b) Inspect the fuel sender gauge assembly.
w/ Canister Pump Module:
Click here
w/o Canister Pump Module:
Click here
| NG |
|
REPLACE FUEL SENDER GAUGE ASSEMBLY w/ Canister Pump Module: Click here
w/o Canister Pump Module: Click here
|
|
|
10. |
INSPECT FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY |
|
*a |
Component without harness connected (Fuel Suction With Pump and Gauge Tube Assembly) |
(a) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
N47-1 (FV) - A-3 |
Always |
Below 1 Ω |
|
N47-2 (FE) - A-2 |
Always |
Below 1 Ω |
|
N47-3 (FS) - A-1 |
Always |
Below 1 Ω |
| OK |
|
CLEAN INSIDE OF FUEL TANK ASSEMBLY |
| NG |
|
REPLACE FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY w/ Canister Pump Module: Click here
w/o Canister Pump Module: Click here
|
|
|