- Gas leak from exhaust system is repaired
- Replacement of air fuel ratio sensor
| Last Modified: 01-30-2024 | 6.11:8.1.0 | Doc ID: RM100000001HGJN |
| Model Year Start: 2019 | Model: RAV4 | Prod Date Range: [02/2019 - 10/2019] |
| Title: FRONT SUSPENSION: FRONT STABILIZER BAR: REMOVAL; 2019 MY RAV4 RAV4 HV [02/2019 - 10/2019] | ||
REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during front stabilizer bar removal/installation are shown below.
Necessary Procedures After Parts Removed/Installed/Replaced (for HV Model:)
|
Replaced Part or Performed Procedure |
Necessary Procedure |
Effect/Inoperative Function when Necessary Procedure not Performed |
Link |
|---|---|---|---|
|
*: When performing learning using the Techstream.
Click here
|
|||
|
Auxiliary battery terminal is disconnected/reconnected |
Perform steering sensor zero point calibration |
Lane control system |
|
|
Parking support brake system (for HV model)* |
|||
|
Pre-collision system |
|||
|
Lighting system (EXT)(w/ AFS) |
|||
|
Memorize steering angle neutral point |
Parking assist monitor system |
|
|
|
Panoramic view monitor system (for HV model) |
|
||
|
Reset back door close position |
Power back door system (for HV model) |
|
|
|
Back door lock initialization |
Power door lock control system |
|
|
|
ECM (w/ Canister Pump Module) |
Perform Vehicle Identification Number (VIN) registration |
DTC P063051 is output |
|
|
Grill shutter switch specification infomation |
Vehicle control history (RoB) [X260E] is stored |
|
|
|
ECM (w/o Canister Pump Module) |
Perform Vehicle Identification Number (VIN) registration |
DTC P063051 is output |
|
|
|
Inspection after repair |
|
w/ Canister Pump Module:
w/o Canister Pump Module:
|
|
Inverter with converter assembly |
Resolver learning |
|
for 2WD:
for AWD:
|
|
Hybrid vehicle transaxle assembly |
|
||
|
Front wheel alignment adjustment |
|
|
|
|
Front bumper assembly (Including removal and installation) |
Front television camera view adjustment |
Panoramic view monitor system (for HV model) |
|
|
Suspension, tires, etc. |
Television camera assembly optical axis (Back camera position setting) |
Parking assist monitor system |
|
|
Panoramic view monitor system (for HV model) |
|
|
|
Replacement of the headlight ECU sub-assembly LH |
|
Lighting system (EXT)(w/ Headlight ECU without AFS) |
|
|
Lighting system (EXT)(w/ AFS) |
|
||
|
Rack and pinion power steering gear assembly |
for Type A:
|
|
|
for Type B:
|
|
|
|
NOTICE:
-
After the power switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the power switch off, be sure to wait for the time specified in the following table before disconnecting the cable from the negative (-) auxiliary battery terminal.
Waiting Time before Disconnecting Cable from Negative (-) Auxiliary Battery Terminal
System Name
See Procedure
Vehicle enrolled in Toyota Entune system or safety connect system
6 minutes
Vehicle not enrolled in Toyota Entune system and safety connect system
1 minute
-
This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.
Click here
![2019 - 2024 MY RAV4 RAV4 HV [11/2018 - ]; INTRODUCTION: REPAIR INSTRUCTION: PRECAUTION](/t3Portal/stylegraphics/info.gif)
Necessary Procedures After Parts Removed/Installed/Replaced (for Gasoline Model:)
|
Replaced Part or Performed Procedure |
Necessary Procedure |
Effect/Inoperative Function when Necessary Procedure not Performed |
Link |
|---|---|---|---|
|
*: When performing learning using the Techstream.
Click here
|
|||
|
Battery terminal is disconnected/reconnected |
Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) |
Stop and start system |
|
|
Perform steering sensor zero point calibration |
Lane control system |
|
|
|
Parking support brake system (for Gasoline model)* |
|||
|
Pre-collision system |
|||
|
Memorize steering angle neutral point |
Parking assist monitor system |
|
|
|
Panoramic view monitor system (for Gasoline model) |
|
||
|
Reset back door close position |
Power back door system (for Gasoline model) |
|
|
|
Back door lock initialization |
Power door lock control system |
|
|
|
ECM |
Perform Vehicle Identification Number (VIN) or frame number registration |
DTC P063051 is output |
w/ Canister Pump Module:
w/o Canister Pump Module:
|
|
ECU communication ID registration |
Engine start function |
w/ Smart Key System:
w/o Smart Key System:
|
|
for UB80E:
|
|
for Initialization:
for Registration:
|
|
for UB80F:
|
|
for Initialization:
for Registration:
|
|
|
Inspection after repair |
|
w/ Canister Pump Module:
w/o Canister Pump Module:
|
|
Automatic transaxle assembly |
for UB80E:
|
|
for Initialization:
for Registration:
|
for UB80F:
|
|
for Initialization:
for Registration:
|
|
|
Replacement of automatic transaxle fluid |
ATF thermal degradation estimate reset |
The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly |
for UB80E:
for UB80F:
|
|
Suspension, tires, etc. (The vehicle height changes because of suspension or tire replacement.) |
Television camera assembly optical axis (Back camera position setting) |
Parking assist monitor system |
|
|
Panoramic view monitor system (for Gasoline model) |
|
|
|
Perform headlight ECU sub-assembly LH initialization |
Lighting system (EXT)(w/ Headlight ECU without AFS) |
|
|
|
Front wheel alignment adjustment |
|
|
|
|
Front bumper assembly (Including removal and installation) |
Front television camera view adjustment |
Panoramic view monitor system (for Gasoline model) |
|
|
Rack and pinion power steering gear assembly |
for Type A:
|
|
|
for Type B:
|
|
|
|
NOTICE:
-
After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, be sure to wait for the time specified in the following table before disconnecting the cable from the negative (-) battery terminal.
Waiting Time before Disconnecting Cable from Negative (-) Auxiliary Battery Terminal
System Name
See Procedure
Vehicle enrolled in Toyota Entune system or safety connect system
6 minutes
Vehicle not enrolled in Toyota Entune system and safety connect system
1 minute
-
This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.
Click here
PROCEDURE
1. SEPARATE FRONT STABILIZER LINK ASSEMBLY LH
|
(a) Remove the nut and separate the front stabilizer link assembly from the front stabilizer bar. NOTICE: Do not damage the boot of the ball joint. HINT: If the ball joint turns together with the nut, use a 6 mm hexagon socket wrench to hold the stud bolt. |
|
2. SEPARATE FRONT STABILIZER LINK ASSEMBLY RH
HINT:
Perform the same procedure as for the LH side.
3. REMOVE ENGINE ASSEMBLY WITH TRANSAXLE
-
for HV Model:
Click here
-
for Gasoline Model:
Click here
4. REMOVE FRONT STABILIZER BAR PROTECTOR (for Gasoline Model)
|
(a) Remove the clip. |
|
(b) Remove the front stabilizer bar protector from the front stabilizer bar.
5. REMOVE FRONT NO. 1 STABILIZER BRACKET LH
|
(a) Remove the 2 bolts and front No. 1 stabilizer bracket LH from the front frame assembly. |
|
6. REMOVE FRONT NO. 1 STABILIZER BRACKET RH
HINT:
Perform the same procedure as for the LH side.
7. REMOVE FRONT STABILIZER BAR
(a) Remove the front stabilizer bar with 2 front stabilizer bar bushings from the front frame assembly.
8. REMOVE FRONT NO. 1 STABILIZER BAR BUSHING (for LH Side)
(a) Remove the front No. 1 stabilizer bar bushing from the front stabilizer bar.
9. REMOVE FRONT NO. 1 STABILIZER BAR BUSHING (for RH Side)
HINT:
Perform the same procedure as for the LH side.
|
|