Last Modified: 01-30-2024 6.11:8.1.0 Doc ID: RM100000001HG9T
Model Year Start: 2019 Model: RAV4 Prod Date Range: [02/2019 - 12/2021]
Title: BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster): Brake Hold Operated Indicator Light Circuit; 2019 - 2021 MY RAV4 RAV4 HV [02/2019 - 12/2021]

Brake Hold Operated Indicator Light Circuit

DESCRIPTION

The brake hold operated indicator light illuminates when the brake hold system is operating (vehicle stopped via brake fluid pressure hold) and turns off when the brake hold system operation is finished (brake fluid pressure decreases).

The brake hold system may not operate depending on vehicle conditions even when the system is in standby mode and the brake hold standby indicator light is illuminated.

If there is a system malfunction that causes brake hold control to be prohibited, when the vehicle is under the following conditions and the brake hold switch (integration control and panel assembly) is turned on, the brake hold operated indicator light blinks.

  • Vehicle Conditions:
    1. The driver's door is closed.
    2. Driver's seat belt is fastened.

HINT:

  • When the ignition switch is turned off during brake hold operation, control stops.
  • If brake hold control does not operate even when the vehicle stops, depress on the brake pedal again firmly to stop the vehicle.

    If brake hold control still does not operate, confirm the conditions for brake hold control to operate.

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake booster with master cylinder assembly), perform initialization and calibration of the linear solenoid valve.

Click here 2019 - 2021 MY RAV4 RAV4 HV [02/2019 - 12/2021]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster): UTILITY

PROCEDURE

1.

PRE-CHECK

(a) Check that the brake hold standby indicator light operates normally.

(b) If the brake hold operated indicator light does not illuminate although the brake hold standby indicator light is illuminated, check that the following brake hold operation (maintaining brake oil pressure) conditions are met.

  1. System is in operation standby state (brake hold operated indicator light is illuminated).
  2. Shift position is not P or R.
  3. Driver is depressing brake pedal and vehicle is fully stopped.
  4. Driver is not depressing accelerator pedal.
  5. Vehicle is not on steep decline.

HINT:

If a malfunction occurs in one of the following systems, the brake hold operated indicator light will blink. If this occurs, perform troubleshooting on the malfunctioning system.

  • Brake system
  • Electric parking brake system
  • Hybrid control system
NEXT

2.

PERFORM ACTIVE TEST USING TECHSTREAM (BRAKE HOLD OPERATED INDICATOR LIGHT)

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(c) Select the Active Test on the Techstream.

Click here 2019 - 2021 MY RAV4 RAV4 HV [02/2019 - 12/2021]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster): DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRAC > Active Test

Tester Display

Measurement Item

Control Range

Diagnostic Note

BH Operated Light

Brake hold operated indicator light

Indicator light ON/OFF

Observe combination meter

(d) Select the Data List on the Techstream.

Click here 2019 - 2021 MY RAV4 RAV4 HV [02/2019 - 12/2021]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster): DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRAC > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

BH Operated Light

Brake hold operated indicator light

ON or OFF

ON: Indicator light on

OFF: Indicator light off

-

Chassis > ABS/VSC/TRAC > Active Test

Active Test Display

BH Operated Light

Data List Display

BH Operated Light

(e) Check the operating condition of the brake hold operated indicator light when operating it using the Techstream.

Result

Proceed to

Brake hold operated indicator light in the Data List does not change using the Active Test.

A

Brake hold operated indicator light in the Data List turns ON/OFF using the Active Test.

B

A

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY 2019 MY RAV4 RAV4 HV [02/2019 - 10/2019]; BRAKE SYSTEM (OTHER): BRAKE BOOSTER (w/o Vacuum Brake Booster): REMOVAL 2020 MY RAV4 RAV4 HV [10/2019 - 08/2020]; BRAKE SYSTEM (OTHER): BRAKE BOOSTER (w/o Vacuum Brake Booster): REMOVAL 2021 MY RAV4 RAV4 HV [08/2020 - 12/2021]; BRAKE SYSTEM (OTHER): BRAKE BOOSTER (w/o Vacuum Brake Booster): REMOVAL

B

3.

INSPECT COMBINATION METER ASSEMBLY

(a) Turn the ignition switch off.

(b) Perform the Active Test of the combination meter assembly (meter CPU) using the Techstream.

Click here 2019 - 2020 MY RAV4 RAV4 HV [11/2018 - 08/2020]; METER / GAUGE / DISPLAY: METER / GAUGE SYSTEM: DATA LIST / ACTIVE TEST 2021 - 2022 MY RAV4 RAV4 HV [08/2020 - 10/2022]; METER / GAUGE / DISPLAY: METER / GAUGE SYSTEM: DATA LIST / ACTIVE TEST

Body Electrical > Combination Meter > Active Test

Tester Display

Hold Indicator

(c) Check the combination meter assembly.

OK:

The brake hold operated indicator light turns on or off in accordance with the Techstream operation.

OK

USE SIMULATION METHOD TO CHECK

NG

INSPECT METER / GAUGE SYSTEM