| Last Modified: 01-30-2024 | 6.11:8.1.0 | Doc ID: RM100000001HFU1 |
| Model Year Start: 2019 | Model: RAV4 | Prod Date Range: [02/2019 - 12/2021] |
| Title: REAR SUSPENSION: REAR SUSPENSION MEMBER (for Gasoline Model AWD): INSTALLATION; 2019 - 2021 MY RAV4 [02/2019 - 12/2021] | ||
INSTALLATION
PROCEDURE
1. INSTALL HOLE PLUG
|
(a) Install the 10 hole plugs to the rear suspension member sub-assembly. HINT: There are 2 different shapes of hole plug. |
|
2. INSTALL REAR NO. 1 DIFFERENTIAL MOUNT CUSHION
Click here
![2019 - 2024 MY RAV4 RAV4 HV [11/2018 - ]; AXLE AND DIFFERENTIAL: DIFFERENTIAL MOUNT CUSHION: INSTALLATION+](/t3Portal/stylegraphics/info.gif)
3. INSTALL REAR SUSPENSION MEMBER FRONT BODY MOUNTING CUSHION (for LH Side)
Click here
4. INSTALL REAR SUSPENSION MEMBER FRONT BODY MOUNTING CUSHION (for RH Side)
Click here
5. INSTALL REAR SUSPENSION MEMBER REAR BODY MOUNT CUSHION LH
Click here
6. INSTALL REAR SUSPENSION MEMBER REAR BODY MOUNT CUSHION RH
Click here
7. INSTALL REAR UPPER CONTROL ARM ASSEMBLY LH
Click here
8. INSTALL REAR UPPER CONTROL ARM ASSEMBLY RH
HINT:
Perform the same procedure as for the LH side.
9. INSTALL REAR SUSPENSION MEMBER SUB-ASSEMBLY
(a) for TMC Made:
(1) Install the 4 rear suspension member cushions to the rear suspension member sub-assembly.
HINT:
When reusing the rear suspension member cushion, make sure to check its identification mark and install it to the correct position.
(b) for TMMC Made:
(1) Install the 2 rear suspension member cushions and 2 upper differential support member stoppers to the rear suspension member sub-assembly.
HINT:
When reusing the rear suspension member cushion and upper differential support member stopper, make sure to check its identification mark and install it to the correct position.
(c) Using an engine lifter and 4 attachments or equivalent tools, support the rear suspension member sub-assembly as shown in the illustration.
CAUTION:
- The rear suspension member sub-assembly is a very heavy component. Make sure that it is supported securely.
- If the rear suspension member sub-assembly is not securely supported, it may drop, resulting in serious injury.
NOTICE:
- Use attachments or equivalent tools to keep the rear suspension member sub-assembly level.
- Keep supporting the rear suspension member sub-assembly until the installation has been completed.
|
*a |
Engine Lifter |
|
*b |
Attachment |
|
Attachment and Wooden Block Placement Location |
(d) Raise the rear suspension member sub-assembly until there is no clearance between the rear suspension member sub-assembly and vehicle.
(e) Install the rear suspension member sub-assembly with the 2 rear suspension member lower stoppers, rear suspension member lower brace LH and rear suspension member lower brace RH, 2 bolts and 4 nuts.
Torque:
Bolt A :
158 N·m {1611 kgf·cm, 117 ft·lbf}
Nut B :
158 N·m {1611 kgf·cm, 117 ft·lbf}
Nut C :
18 N·m {184 kgf·cm, 13 ft·lbf}
(f) except Torque Vectoring Differential, w/ Height Control Sensor:
(1) Engage the 7 clamps to install the differential carrier wire harness.
(g) except Torque Vectoring Differential, w/o Height Control Sensor:
(1) Engage the 6 clamps to install the differential carrier wire harness.
10. TEMPORARILY INSTALL REAR NO. 1 SUSPENSION ARM ASSEMBLY LH
(a) Temporarily install the rear No. 1 suspension arm assembly to the rear suspension member sub-assembly with the bolt and nut.
NOTICE:
- Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured.
- Insert the bolt with the threaded end facing the rear of the vehicle.
11. TEMPORARILY INSTALL REAR NO. 1 SUSPENSION ARM ASSEMBLY RH
HINT:
Perform the same procedure as for the LH side.
12. TEMPORARILY INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY LH
Click here
13. TEMPORARILY INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY RH
HINT:
Perform the same procedure as for the LH side.
14. INSTALL TORQUE VECTORING DIFFERENTIAL CARRIER ASSEMBLY (for Torque Vectoring Differential)
Click here
15. INSTALL REAR DIFFERENTIAL CARRIER ASSEMBLY (except Torque Vectoring Differential)
Click here
16. STABILIZE SUSPENSION
Click here
17. INSTALL REAR NO. 1 SUSPENSION ARM ASSEMBLY LH
Click here
18. INSTALL REAR NO. 1 SUSPENSION ARM ASSEMBLY RH
HINT:
Perform the same procedure as for the LH side.
19. INSTALL REAR WHEEL
Click here
20. INSPECT AND ADJUST REAR WHEEL ALIGNMENT
Click here
21. PERFORM INITIALIZATION
Click here
|
|