| Last Modified: 01-30-2024 | 6.11:8.1.0 | Doc ID: RM100000001HCDT |
| Model Year Start: 2019 | Model: RAV4 | Prod Date Range: [02/2019 - 10/2019] |
| Title: STEERING COLUMN: STEERING WHEEL: REMOVAL; 2019 MY RAV4 RAV4 HV [02/2019 - 10/2019] | ||
REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during steering wheel removal/installation are shown below.
Necessary Procedures After Parts Removed/Installed/Replaced (for HV Model)
|
Replaced Part or Performed Procedure |
Necessary Procedure |
Effect/Inoperative Function when Necessary Procedure not Performed |
Link |
|---|---|---|---|
|
Auxiliary battery terminal is disconnected/reconnected |
Perform steering sensor zero point calibration |
Lane control system |
|
|
Parking support brake system (for HV model)* |
|||
|
Pre-collision system |
|||
|
Lighting system (EXT)(w/ AFS) |
|||
|
Memorize steering angle neutral point |
Parking assist monitor system |
|
|
|
Panoramic view monitor system (for HV model) |
|
||
|
Reset back door close position |
Power back door system (for HV model) |
|
|
|
Back door lock initialization |
Power door lock control system |
|
NOTICE:
After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, be sure to wait for the time specified in the following table before disconnecting the cable from the negative (-) auxiliary battery terminal.
Waiting Time before Disconnecting Cable from Negative (-) Auxiliary Battery Terminal
|
System Name |
See Procedure |
|---|---|
|
Vehicle enrolled in Toyota Entune system or safety connect system |
6 minutes |
|
Vehicle not enrolled in Toyota Entune system and safety connect system |
1 minute |
Necessary Procedures After Parts Removed/Installed/Replaced (for Gasoline Model)
|
Replaced Part or Performed Procedure |
Necessary Procedure |
Effect/Inoperative Function when Necessary Procedure not Performed |
Link |
|---|---|---|---|
|
*: When performing learning using the Techstream.
Click here
|
|||
|
Battery terminal is disconnected/reconnected |
Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) |
Stop and start system |
|
|
Perform steering sensor zero point calibration |
Lane control system |
|
|
|
Parking support brake system (for Gasoline model)* |
|||
|
Pre-collision system |
|||
|
Memorize steering angle neutral point |
Parking assist monitor system |
|
|
|
Panoramic view monitor system (for Gasoline model) |
|
||
|
Reset back door close position |
Power back door system (for Gasoline model) |
|
|
|
Back door lock initialization |
Power door lock control system |
|
|
NOTICE:
After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, be sure to wait for the time specified in the following table before disconnecting the cable from the negative (-) auxiliary battery terminal.
Waiting Time before Disconnecting Cable from Negative (-) Auxiliary Battery Terminal
|
System Name |
See Procedure |
|---|---|
|
Vehicle enrolled in Toyota Entune system or safety connect system |
6 minutes |
|
Vehicle not enrolled in Toyota Entune system and safety connect system |
1 minute |
PROCEDURE
1. PRECAUTION
CAUTION:
Be sure to read precaution thoroughly before servicing.
-
w/ Occupant Classification System: Click here
![2019 - 2020 MY RAV4 RAV4 HV [02/2019 - 08/2020]; SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM (w/ Occupant Classification System): PRECAUTION](/t3Portal/stylegraphics/info.gif)
-
w/o Occupant Classification System: Click here
NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
2. PLACE FRONT WHEELS FACING STRAIGHT AHEAD
3. REMOVE DECK BOARD ASSEMBLY (for HV Model)
Click here
4. REMOVE REAR NO. 2 FLOOR BOARD (for HV Model)
Click here
5. REMOVE BATTERY HOLE COVER (for HV Model)
Click here
6. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL
-
for A25A-FKS: Click here
-
for A25A-FXS: Click here
CAUTION:
-
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
- If the airbag deploys for any reason, it may cause a serious accident.
NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click here
7. REMOVE HORN BUTTON ASSEMBLY
Click here
8. REMOVE STEERING PAD SWITCH ASSEMBLY
Click here
9. REMOVE STEERING WHEEL ASSEMBLY
|
(a) Remove the steering wheel set bolt. |
|
|
(b) Put matchmarks on the steering wheel and steering main shaft. |
|
|
(c) Using SST, remove the steering wheel assembly. SST: 09950-50013 09951-05010 09952-05010 09953-05020 09954-05031 09957-04010 SST: 09950-60011 09951-00330 NOTICE: Apply a small amount of grease to the threads and tip of SST (09953-05020) before use. |
|
10. REMOVE NO. 1 TRANSMISSION SHIFT SWITCH ASSEMBLY (w/ Shift Paddle Switch)
Click here
11. REMOVE NO. 2 TRANSMISSION SHIFT SWITCH ASSEMBLY (w/ Shift Paddle Switch)
HINT:
Use the same procedure described for the No. 1 transmission shift switch assembly.
|
|