Last Modified: 01-30-2024 6.11:8.1.0 Doc ID: RM100000001H3N3
Model Year Start: 2019 Model: RAV4 HV Prod Date Range: [02/2019 -           ]
Title: HYBRID / BATTERY CONTROL: HYBRID CONTROL SYSTEM (for AWD with NICKEL METAL HYDRIDE BATTERY): P0A3011,P0A3015; Drive Motor "B" Temperature Sensor Circuit Short to Ground; 2019 - 2024 MY RAV4 HV [02/2019 -        ]

DTC

P0A3011

Drive Motor "B" Temperature Sensor Circuit Short to Ground

DTC

P0A3015

Drive Motor "B" Temperature Sensor Circuit Short to Battery or Open

DTC SUMMARY

MALFUNCTION DESCRIPTION

These DTCs are stored when the rear motor temperature sensor output is abnormal. The cause of this malfunction may be one of the following:

Hybrid vehicle control ECU assembly malfunction

  • Hybrid vehicle control ECU assembly internal malfunction

Rear motor temperature sensor malfunction

  • Internal rear motor temperature sensor malfunction
  • Open or short in rear motor temperature sensor

Wire harness between the rear motor temperature sensor and hybrid vehicle control ECU assembly

  • The connectors are not connected properly
  • Foreign matter or water on the connector terminals
  • Open or short in wire harness

HINT:

If any of these DTCs are stored, the rear motor temperature sensor is malfunctioning and the self-protection function may not operate. Therefore under certain high load driving condition, the temperature of the rear motor (MGR) becomes high. If the self-protection function does not operate, the rear motor (MGR) may malfunction and cause the vehicle to enter fail-safe mode.

DESCRIPTION

The resistance of the thermistor built into the rear motor temperature sensor changes in accordance with changes in the rear motor temperature. The lower the rear motor temperature, the higher the thermistor resistance. Conversely, the higher the rear motor temperature, the lower the resistance.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

MIL

Warning Indicate

P0A3011

Drive Motor "B" Temperature Sensor Circuit Short to Ground

Short to ground in the rear motor temperature sensor circuit

(1 trip detection logic)

  • Wire harness or connector
  • Hybrid vehicle control ECU assembly
  • Rear motor temperature sensor (Rear traction motor with transaxle assembly)

Does not come on

Master Warning: Comes on

P0A3015

Drive Motor "B" Temperature Sensor Circuit Short to Battery or Open

Open or short to +B in the rear motor temperature sensor circuit

(1 trip detection logic)

  • Wire harness or connector
  • Hybrid vehicle control ECU assembly
  • Rear motor temperature sensor (Rear traction motor with transaxle assembly)

Does not come on

Master Warning: Comes on

Related Data List

DTC No.

Data List

P0A3011

Rear Motor Temperature

P0A3015

HINT:

After confirming that DTC P0A3011 or P0A3015 is output, use the Techstream to check "Rear Motor Temperature" in the Data List.

Displayed Temperature

Malfunction

-40°C (-40°F)

Open circuit or short to +B

215°C (419°F)

Short to ground

CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click here 2019 - 2024 MY RAV4 HV [02/2019 -        ]; HYBRID / BATTERY CONTROL: HYBRID CONTROL SYSTEM (for AWD with NICKEL METAL HYDRIDE BATTERY): UTILITY

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON and turn the Techstream on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  4. Turn the ignition switch off and wait for 2 minutes or more.
  5. Turn the ignition switch to ON and turn the Techstream on.
  6. With the ignition switch ON and wait for 5 seconds or more.
  7. Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.
  8. Check the DTC judgment result.

    HINT:

    • If the judgment result shows NORMAL, the system is normal.
    • If the judgment result shows ABNORMAL, the system has a malfunction.
    • If the judgment result shows INCOMPLETE, perform driving pattern again.

WIRING DIAGRAM

PROCEDURE

1.

CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU ASSEMBLY CONNECTOR)

(a) Check the connection condition of the hybrid vehicle control ECU assembly connectors and the contact pressure of each terminal. Check the terminals for deformation, and check the connector for water ingress and foreign matter.

Click here 2019 - 2024 MY RAV4 RAV4 HV [11/2018 -        ]; INTRODUCTION: HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS: ELECTRONIC CIRCUIT INSPECTION PROCEDURE

OK:

- The connector is connected securely.

- The terminals are not deformed and are connected securely.

- No water or foreign matter in the connector.

Result

Proceed to

OK

A

NG (The connector is not connected securely.)

B

NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.)

C

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

A

2.

CHECK CONNECTOR CONNECTION CONDITION (NO. 2 FLOOR WIRE CONNECTOR)

(a) Check the connection condition of the rear motor temperature sensor connector (No. 2 floor wire connector) and the contact pressure of each terminal. Check the terminal for deformation, and check the connector for water ingress and foreign matter.

Click here 2019 - 2024 MY RAV4 RAV4 HV [11/2018 -        ]; INTRODUCTION: HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS: ELECTRONIC CIRCUIT INSPECTION PROCEDURE

OK:

- The connector is connected securely.

- The terminals are not deformed and are connected securely.

- No water or foreign matter in the connectors.

Result

Proceed to

OK

A

NG (The connector is not connected securely.)

B

NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.)

C

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

A

3.

CHECK CONNECTOR CONNECTION CONDITION (FRAME WIRE CONNECTOR)

(a) Check the connection condition of the rear motor temperature sensor connector (frame wire connector) and the contact pressure of each terminal. Check the terminals for deformation, and check the connector for water ingress and foreign matter.

Click here 2019 - 2024 MY RAV4 RAV4 HV [11/2018 -        ]; INTRODUCTION: HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS: ELECTRONIC CIRCUIT INSPECTION PROCEDURE

OK:

- The connector is connected securely.

- The terminals are not deformed and are connected securely.

- No water or foreign matter in the connector.

Result

Proceed to

OK

A

NG (The connector is not connected securely.)

B

NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.)

C

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

A

4.

READ VALUE USING TECHSTREAM (REAR MOTOR TEMPERATURE)

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(c) Enter the following menus: Powertrain / Hybrid Control / Data List / Rear Motor Temperature.

(d) Read the Data List.

Powertrain > Hybrid Control > Data List

Tester Display

Rear Motor Temperature

Result

Proceed to

-40°C (-40°F)

A

215°C (419°F)

B

Same as actual temperature

C

(e) Turn the ignition switch off.

B

GO TO STEP 9

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

A

5.

READ VALUE USING TECHSTREAM (CHECK WIRE HARNESS OPEN CIRCUIT)

(a) Disconnect the ON1 frame wire connector.

(b) Connect terminals 1 (RMTG) and 2 (RMT) of the ON1 frame wire connector (hybrid vehicle control ECU assembly side).

*a

Front view of frame wire connector

(Hybrid Vehicle Control ECU Assembly Side)

(c) Connect the Techstream to the DLC3.

(d) Turn the ignition switch to ON.

(e) Enter the following menus: Powertrain / Hybrid Control / Data List / Rear Motor Temperature.

(f) Read the Data List.

Powertrain > Hybrid Control > Data List

Tester Display

Rear Motor Temperature

OK:

Tester Display

Condition

Specified Condition

Rear Motor Temperature

Terminals ON1-1 (RMTG) and ON1-2 (RMT) connected

Ignition switch ON

215°C (419°F)

(g) Turn the ignition switch off.

(h) Reconnect the ON1 frame wire connector.

NG

GO TO STEP 8

OK

6.

CHECK CONNECTOR CONNECTION CONDITION (REAR MOTOR TEMPERATURE SENSOR CONNECTOR)

(a) Remove the rear suspension member sub-assembly.

Click here 2019 - 2020 MY RAV4 HV [02/2019 - 06/2020]; REAR SUSPENSION: REAR SUSPENSION MEMBER (for HV Model AWD): REMOVAL 2020 MY RAV4 HV [06/2020 - 08/2020]; REAR SUSPENSION: REAR SUSPENSION MEMBER (for HV Model AWD): REMOVAL 2021 MY RAV4 HV [08/2020 - 12/2021]; REAR SUSPENSION: REAR SUSPENSION MEMBER (for HV Model AWD): REMOVAL 2022 MY RAV4 HV [12/2021 - 10/2022]; REAR SUSPENSION: REAR SUSPENSION MEMBER (for HV Model AWD): REMOVAL 2023 MY RAV4 HV [10/2022 - 10/2023]; REAR SUSPENSION: REAR SUSPENSION MEMBER (for HV Model AWD): REMOVAL 2024 MY RAV4 HV [10/2023 -        ]; REAR SUSPENSION: REAR SUSPENSION MEMBER (for HV Model AWD): REMOVAL

(b) Check the connection condition of the rear motor temperature sensor connector and the contact pressure of each terminal. Check the terminals for deformation, and check the connector for water ingress and foreign matter.

Click here 2019 - 2024 MY RAV4 RAV4 HV [11/2018 -        ]; INTRODUCTION: HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS: ELECTRONIC CIRCUIT INSPECTION PROCEDURE

OK:

- The connector is connected securely.

- The terminals are not deformed and are connected securely.

- No water or foreign matter in the connector.

Result

Proceed to

OK

A

NG (The connector is not connected securely.)

B

NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.)

C

(c) Install the rear suspension member sub-assembly.

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

A

7.

INSPECT REAR TRACTION MOTOR WITH TRANSAXLE ASSEMBLY (REAR MOTOR TEMPERATURE SENSOR)

(a) Remove the rear suspension member sub-assembly.

Click here 2019 - 2020 MY RAV4 HV [02/2019 - 06/2020]; REAR SUSPENSION: REAR SUSPENSION MEMBER (for HV Model AWD): REMOVAL 2020 MY RAV4 HV [06/2020 - 08/2020]; REAR SUSPENSION: REAR SUSPENSION MEMBER (for HV Model AWD): REMOVAL 2021 MY RAV4 HV [08/2020 - 12/2021]; REAR SUSPENSION: REAR SUSPENSION MEMBER (for HV Model AWD): REMOVAL 2022 MY RAV4 HV [12/2021 - 10/2022]; REAR SUSPENSION: REAR SUSPENSION MEMBER (for HV Model AWD): REMOVAL 2023 MY RAV4 HV [10/2022 - 10/2023]; REAR SUSPENSION: REAR SUSPENSION MEMBER (for HV Model AWD): REMOVAL 2024 MY RAV4 HV [10/2023 -        ]; REAR SUSPENSION: REAR SUSPENSION MEMBER (for HV Model AWD): REMOVAL

(b) Disconnect the O2 rear motor temperature sensor connector.

(c) Measure the resistance according to the value(s) in the table below.

OK:

Tester Display

Switch Condition

Specified Condition

1 (RMTG) - 2 (RMT)

Ignition switch off

0.3443 to 1446 kΩ

(d) Connect the O2 rear motor temperature sensor connector.

*a

Component without harness connected

(Rear Motor Temperature Sensor (Rear Traction Motor with Transaxle Assembly))

(e) Install the rear suspension member sub-assembly.

OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (REAR MOTOR TEMPERATURE SENSOR - NO. 2 FLOOR WIRE)

NG

REPLACE REAR TRACTION MOTOR WITH TRANSAXLE ASSEMBLY 2019 MY RAV4 HV [02/2019 - 10/2019]; Q610 (HYBRID TRANSMISSION / TRANSAXLE): REAR TRACTION MOTOR: REMOVAL 2020 MY RAV4 HV [10/2019 - 06/2020]; Q610 (HYBRID TRANSMISSION / TRANSAXLE): REAR TRACTION MOTOR: REMOVAL 2020 MY RAV4 HV [06/2020 - 08/2020]; Q610 (HYBRID TRANSMISSION / TRANSAXLE): REAR TRACTION MOTOR: REMOVAL 2021 MY RAV4 HV [08/2020 - 12/2021]; Q610 (HYBRID TRANSMISSION / TRANSAXLE): REAR TRACTION MOTOR: REMOVAL 2022 MY RAV4 HV [12/2021 - 10/2022]; Q610 (HYBRID TRANSMISSION / TRANSAXLE): REAR TRACTION MOTOR: REMOVAL 2023 MY RAV4 HV [10/2022 - 10/2023]; Q610 (HYBRID TRANSMISSION / TRANSAXLE): REAR TRACTION MOTOR: REMOVAL 2024 MY RAV4 HV [10/2023 -        ]; Q610 (HYBRID TRANSMISSION / TRANSAXLE): REAR TRACTION MOTOR: REMOVAL

8.

CHECK HYBRID VEHICLE CONTROL ECU ASSEMBLY

(a) Connect terminals 42 (RMT) and 43 (RMTG) of the A29 hybrid vehicle control ECU assembly connector.

*a

Component with harness connected

(Hybrid Vehicle Control ECU Assembly)

-

-

(b) Connect the Techstream to the DLC3.

(c) Turn the ignition switch to ON.

(d) Enter the following menus: Powertrain / Hybrid Control / Data List / Rear Motor Temperature.

(e) Read the Data List.

Powertrain > Hybrid Control > Data List

Tester Display

Rear Motor Temperature

OK:

Tester Display

Condition

Specified Condition

Rear Motor Temperature

Terminals A29-42 (RMT) and A29-43 (RMTG) connected

Ignition switch ON

215°C (419°F)

(f) Turn the ignition switch off.

OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (FRAME WIRE - HYBRID VEHICLE CONTROL ECU ASSEMBLY)

NG

REPLACE HYBRID VEHICLE CONTROL ECU ASSEMBLY 2019 MY RAV4 HV [02/2019 - 10/2019]; HYBRID / BATTERY CONTROL: HYBRID VEHICLE CONTROL ECU: REMOVAL 2020 MY RAV4 HV [10/2019 - 08/2020]; HYBRID / BATTERY CONTROL: HYBRID VEHICLE CONTROL ECU: REMOVAL 2021 MY RAV4 HV [08/2020 - 12/2021]; HYBRID / BATTERY CONTROL: HYBRID VEHICLE CONTROL ECU: REMOVAL 2022 MY RAV4 HV [12/2021 - 10/2022]; HYBRID / BATTERY CONTROL: HYBRID VEHICLE CONTROL ECU: REMOVAL 2023 MY RAV4 HV [10/2022 - 10/2023]; HYBRID / BATTERY CONTROL: HYBRID VEHICLE CONTROL ECU: REMOVAL 2024 MY RAV4 HV [10/2023 -        ]; HYBRID / BATTERY CONTROL: HYBRID VEHICLE CONTROL ECU: REMOVAL

9.

READ VALUE USING TECHSTREAM (CHECK WIRE HARNESS SHORT CIRCUIT)

(a) Disconnect the ON1 frame wire connector.

(b) Connect the Techstream to the DLC3.

(c) Turn the ignition switch to ON.

(d) Enter the following menus: Powertrain / Hybrid Control / Data List / Rear Motor Temperature.

(e) Read the Data List.

Powertrain > Hybrid Control > Data List

Tester Display

Rear Motor Temperature

OK:

Tester Display

Switch Condition

Specified Condition

Rear Motor Temperature

Ignition switch ON

-40°C

(f) Turn the ignition switch off.

(g) Reconnect the ON1 frame wire connector.

NG

GO TO STEP 12

OK

10.

CHECK CONNECTOR CONNECTION CONDITION (REAR MOTOR TEMPERATURE SENSOR CONNECTOR)

(a) Remove the rear suspension member sub-assembly.

Click here 2019 - 2020 MY RAV4 HV [02/2019 - 06/2020]; REAR SUSPENSION: REAR SUSPENSION MEMBER (for HV Model AWD): REMOVAL 2020 MY RAV4 HV [06/2020 - 08/2020]; REAR SUSPENSION: REAR SUSPENSION MEMBER (for HV Model AWD): REMOVAL 2021 MY RAV4 HV [08/2020 - 12/2021]; REAR SUSPENSION: REAR SUSPENSION MEMBER (for HV Model AWD): REMOVAL 2022 MY RAV4 HV [12/2021 - 10/2022]; REAR SUSPENSION: REAR SUSPENSION MEMBER (for HV Model AWD): REMOVAL 2023 MY RAV4 HV [10/2022 - 10/2023]; REAR SUSPENSION: REAR SUSPENSION MEMBER (for HV Model AWD): REMOVAL 2024 MY RAV4 HV [10/2023 -        ]; REAR SUSPENSION: REAR SUSPENSION MEMBER (for HV Model AWD): REMOVAL

(b) Check the connection condition of the rear motor temperature sensor connector and the contact pressure of each terminal. Check the terminals for deformation, and check the connector for water ingress and foreign matter.

Click here 2019 - 2024 MY RAV4 RAV4 HV [11/2018 -        ]; INTRODUCTION: HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS: ELECTRONIC CIRCUIT INSPECTION PROCEDURE

OK:

- The connector is connected securely.

- The terminals are not deformed and are connected securely.

- No water or foreign matter in the connector.

Result

Proceed to

OK

A

NG (The connector is not connected securely.)

B

NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.)

C

(c) Install the rear suspension member sub-assembly.

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

A

11.

INSPECT REAR TRACTION MOTOR WITH TRANSAXLE ASSEMBLY (REAR MOTOR TEMPERATURE SENSOR)

(a) Remove the rear suspension member sub-assembly.

Click here 2019 - 2020 MY RAV4 HV [02/2019 - 06/2020]; REAR SUSPENSION: REAR SUSPENSION MEMBER (for HV Model AWD): REMOVAL 2020 MY RAV4 HV [06/2020 - 08/2020]; REAR SUSPENSION: REAR SUSPENSION MEMBER (for HV Model AWD): REMOVAL 2021 MY RAV4 HV [08/2020 - 12/2021]; REAR SUSPENSION: REAR SUSPENSION MEMBER (for HV Model AWD): REMOVAL 2022 MY RAV4 HV [12/2021 - 10/2022]; REAR SUSPENSION: REAR SUSPENSION MEMBER (for HV Model AWD): REMOVAL 2023 MY RAV4 HV [10/2022 - 10/2023]; REAR SUSPENSION: REAR SUSPENSION MEMBER (for HV Model AWD): REMOVAL 2024 MY RAV4 HV [10/2023 -        ]; REAR SUSPENSION: REAR SUSPENSION MEMBER (for HV Model AWD): REMOVAL

(b) Disconnect the O2 rear motor temperature sensor connector.

(c) Measure the resistance according to the value(s) in the table below.

OK:

Tester Display

Switch Condition

Specified Condition

1 (RMTG) - 2 (RMT)

Ignition switch off

0.3443 to 1446 kΩ

(d) Connect the O2 rear motor temperature sensor connector.

*a

Component without harness connected

(Rear Motor Temperature Sensor (Rear Traction Motor with Transaxle Assembly))

(e) Install the rear suspension member sub-assembly.

OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (REAR MOTOR TEMPERATURE SENSOR - NO. 2 FLOOR WIRE)

NG

REPLACE REAR TRACTION MOTOR WITH TRANSAXLE ASSEMBLY 2019 MY RAV4 HV [02/2019 - 10/2019]; Q610 (HYBRID TRANSMISSION / TRANSAXLE): REAR TRACTION MOTOR: REMOVAL 2020 MY RAV4 HV [10/2019 - 06/2020]; Q610 (HYBRID TRANSMISSION / TRANSAXLE): REAR TRACTION MOTOR: REMOVAL 2020 MY RAV4 HV [06/2020 - 08/2020]; Q610 (HYBRID TRANSMISSION / TRANSAXLE): REAR TRACTION MOTOR: REMOVAL 2021 MY RAV4 HV [08/2020 - 12/2021]; Q610 (HYBRID TRANSMISSION / TRANSAXLE): REAR TRACTION MOTOR: REMOVAL 2022 MY RAV4 HV [12/2021 - 10/2022]; Q610 (HYBRID TRANSMISSION / TRANSAXLE): REAR TRACTION MOTOR: REMOVAL 2023 MY RAV4 HV [10/2022 - 10/2023]; Q610 (HYBRID TRANSMISSION / TRANSAXLE): REAR TRACTION MOTOR: REMOVAL 2024 MY RAV4 HV [10/2023 -        ]; Q610 (HYBRID TRANSMISSION / TRANSAXLE): REAR TRACTION MOTOR: REMOVAL

12.

CHECK HARNESS AND CONNECTOR (FRAME WIRE - HYBRID VEHICLE CONTROL ECU ASSEMBLY)

(a) Disconnect the ON1 frame wire connector.

(b) Disconnect the A29 hybrid vehicle control ECU assembly connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):

Tester Display

Switch Condition

Specified Condition

ON1-1 (RMTG) - A29-43 (RMTG)

Ignition switch off

Below 1 Ω

ON1-2 (RMT) - A29-42 (RMT)

Ignition switch off

Below 1 Ω

Standard Resistance (Check for Short):

Tester Display

Switch Condition

Specified Condition

ON1-1 (RMTG) or A29-43 (RMTG) - Body ground and other terminals

Ignition switch off

10 kΩ or higher

ON1-2 (RMT) or A29-42 (RMT) - Body ground and other terminals

Ignition switch off

10 kΩ or higher

*a

Front view of frame wire connector

(Hybrid Vehicle Control ECU Assembly Side)

*b

Front view of wire harness connector

(to Hybrid Vehicle Control ECU Assembly)

(d) Connect the A29 hybrid vehicle control ECU assembly connector.

(e) Connect the ON1 frame wire connector.

OK

REPLACE HYBRID VEHICLE CONTROL ECU ASSEMBLY 2019 MY RAV4 HV [02/2019 - 10/2019]; HYBRID / BATTERY CONTROL: HYBRID VEHICLE CONTROL ECU: REMOVAL 2020 MY RAV4 HV [10/2019 - 08/2020]; HYBRID / BATTERY CONTROL: HYBRID VEHICLE CONTROL ECU: REMOVAL 2021 MY RAV4 HV [08/2020 - 12/2021]; HYBRID / BATTERY CONTROL: HYBRID VEHICLE CONTROL ECU: REMOVAL 2022 MY RAV4 HV [12/2021 - 10/2022]; HYBRID / BATTERY CONTROL: HYBRID VEHICLE CONTROL ECU: REMOVAL 2023 MY RAV4 HV [10/2022 - 10/2023]; HYBRID / BATTERY CONTROL: HYBRID VEHICLE CONTROL ECU: REMOVAL 2024 MY RAV4 HV [10/2023 -        ]; HYBRID / BATTERY CONTROL: HYBRID VEHICLE CONTROL ECU: REMOVAL

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR