Last Modified: 01-30-2024 6.11:8.1.0 Doc ID: RM100000001H3MT
Model Year Start: 2019 Model: RAV4 HV Prod Date Range: [02/2019 - 06/2020]
Title: HYBRID / BATTERY CONTROL: HYBRID CONTROL SYSTEM (for AWD with NICKEL METAL HYDRIDE BATTERY): P0AFC62; Hybrid/EV Battery Sensor Module Signal Compare Failure; 2019 - 2020 MY RAV4 HV [02/2019 - 06/2020]

DTC

P0AFC62

Hybrid/EV Battery Sensor Module Signal Compare Failure

DESCRIPTION

Refer to the description for DTC P1AC000.

Click here 2019 - 2024 MY RAV4 HV [02/2019 -        ]; HYBRID / BATTERY CONTROL: HYBRID CONTROL SYSTEM (for AWD with NICKEL METAL HYDRIDE BATTERY): P1AC000; Hybrid/EV Battery Cell Low Voltage+

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

MIL

Warning Indicate

P0AFC62

Hybrid/EV Battery Sensor Module Signal Compare Failure

The difference between the voltage output by detection circuit C and the total of the voltage output by detection circuits A and B exceeds the threshold.

HINT: The battery voltage sensor uses 3 voltage detection circuits (A, B and C) to detect the voltage of the battery blocks.

(1 trip detection logic)

Battery voltage sensor

Comes on

Master Warning:

Comes on

MONITOR DESCRIPTION

If the battery voltage sensor detects a voltage drop in a battery block, the hybrid vehicle control ECU assembly will illuminate the MIL and store a DTC.

MONITOR STRATEGY

Related DTCs

P0AFC (INF P0AFC62): Battery voltage sensor circuit malfunction

Required sensors/components

Battery voltage sensor

Frequency of operation

Continuous

Duration

TMC's intellectual property

MIL operation

Immediately

Sequence of operation

None

TYPICAL ENABLING CONDITIONS

The monitor will run whenever the following DTCs are not stored

TMC's intellectual property

Other conditions belong to TMC's intellectual property

-

TYPICAL MALFUNCTION THRESHOLDS

TMC's intellectual property

-

COMPONENT OPERATING RANGE

Battery voltage sensor

DTC P0AFC (INF P0AFC62) is not detected

CONFIRMATION DRIVING PATTERN

HINT:

  • After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

    Click here 2019 - 2024 MY RAV4 HV [02/2019 -        ]; HYBRID / BATTERY CONTROL: HYBRID CONTROL SYSTEM (for AWD with NICKEL METAL HYDRIDE BATTERY): UTILITY

  • When clearing the permanent DTCs, refer to the "CLEAR PERMANENT DTC" procedure.

    Click here 2019 - 2022 MY RAV4 HV [02/2019 - 10/2022]; HYBRID / BATTERY CONTROL: HYBRID CONTROL SYSTEM (for AWD with NICKEL METAL HYDRIDE BATTERY): DTC CHECK / CLEAR

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON and turn the Techstream on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  4. Turn the ignition switch off and wait for 2 minutes or more.
  5. Turn the ignition switch to ON and turn the Techstream on.
  6. With ignition switch ON and wait for 20 seconds or more. [*1]

    HINT:

    [*1]: Normal judgment procedure.

    The normal judgment procedure is used to complete DTC judgment and also used when clearing permanent DTCs.

  7. Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.
  8. Check the DTC judgment result.

    HINT:

    • If the judgment result shows NORMAL, the system is normal.
    • If the judgment result shows ABNORMAL, the system has a malfunction.
    • If the judgment result shows INCOMPLETE, perform the normal judgment procedure again.

CAUTION / NOTICE / HINT

CAUTION:

  • Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the service plug grip from HV battery.
    • Inspecting the high-voltage system
    • Disconnecting the low voltage connector of the inverter with converter assembly
    • Disconnecting the low voltage connector of the HV battery
  • To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.
  • After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.
  • After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

    Click here 2019 - 2024 MY RAV4 HV [02/2019 -        ]; HYBRID / BATTERY CONTROL: HYBRID CONTROL SYSTEM (for AWD with NICKEL METAL HYDRIDE BATTERY): PRECAUTION

    HINT:

    Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.

    *a

    Without waiting for 10 minutes

  • Make sure to insulate the high-voltage connectors and terminals of the HV battery with insulating tape after removing it.

    If the HV battery stored without insulating the connectors and terminals, electric shock or fire may result.

  • When disposing of an HV battery, make sure to return it through an authorized collection agent who is capable of handling it safely. If the HV battery is returned via the manufacturer specified route, it will be returned properly and in a safe manner by an authorized collection agent.

    *a

    Dealer

    *b

    Battery Collection Agent

    • Accidents such as electric shock may result if the HV battery is disposed of improperly or abandoned. Therefore, make sure to return all HV batteries through an authorized collection agent.
  • After removing the HV battery, keep it away from water. Exposure to water may cause the HV battery to produce heat, resulting in a fire.

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click here 2019 - 2024 MY RAV4 RAV4 HV [11/2018 -        ]; INTRODUCTION: REPAIR INSTRUCTION: PRECAUTION

PROCEDURE

1.

CHECK DTC OUTPUT (HYBRID CONTROL)

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(c) Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

(d) Check and record any HV system DTCs and freeze frame data.

(e) Read output DTCs.

Powertrain > Hybrid Control > Trouble Codes

Result

Proceed to

"P0A9563, P0AFC00, P0AFC96 or P308A12" is not output.

A

"P0A9563, P0AFC00, P0AFC96 or P308A12" is also output.

B

(f) Turn the ignition switch off.

B

GO TO DTC CHART (HYBRID CONTROL SYSTEM)

A

2.

CHECK CONNECTOR CONNECTION CONDITION

CAUTION:

Be sure to wear insulated gloves.

(a) Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

(b) Remove the No. 1 hybrid battery exhaust duct.

Click here 2019 MY RAV4 HV [02/2019 - 10/2019]; HYBRID / BATTERY CONTROL: HV BATTERY (for NICKEL METAL HYDRIDE BATTERY): REMOVAL+ 2020 MY RAV4 HV [10/2019 - 06/2020]; HYBRID / BATTERY CONTROL: HV BATTERY (for NICKEL METAL HYDRIDE BATTERY): REMOVAL+

(c) Remove the No. 1 HV battery shield panel.

Click here 2019 MY RAV4 HV [02/2019 - 10/2019]; HYBRID / BATTERY CONTROL: BATTERY VOLTAGE SENSOR: REMOVAL+ 2020 MY RAV4 HV [10/2019 - 08/2020]; HYBRID / BATTERY CONTROL: BATTERY VOLTAGE SENSOR: REMOVAL+

(d) Check the connector connections and contact pressure of the relevant terminals for the battery voltage sensor.

Click here 2019 - 2024 MY RAV4 RAV4 HV [11/2018 -        ]; INTRODUCTION: HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS: ELECTRONIC CIRCUIT INSPECTION PROCEDURE

OK:

The connector is connected securely and there are no contact problems.

(e) Install the No. 1 HV battery shield panel.

(f) Install the No. 1 hybrid battery exhaust duct.

OK

REPLACE BATTERY VOLTAGE SENSOR 2019 MY RAV4 HV [02/2019 - 10/2019]; HYBRID / BATTERY CONTROL: BATTERY VOLTAGE SENSOR: REMOVAL 2020 MY RAV4 HV [10/2019 - 08/2020]; HYBRID / BATTERY CONTROL: BATTERY VOLTAGE SENSOR: REMOVAL

NG

CONNECT SECURELY