Last Modified: 01-30-2024 6.11:8.1.0 Doc ID: RM100000001H3K5
Model Year Start: 2019 Model: RAV4 HV Prod Date Range: [02/2019 -           ]
Title: HYBRID / BATTERY CONTROL: HYBRID CONTROL SYSTEM (for AWD with NICKEL METAL HYDRIDE BATTERY): P253012; IG2 Signal Circuit Short to Auxiliary Battery; 2019 - 2024 MY RAV4 HV [02/2019 -        ]

DTC

P253012

IG2 Signal Circuit Short to Auxiliary Battery

DESCRIPTION

w/ Smart Key System:

  • The hybrid vehicle control ECU assembly compares the IG2 signal to the IG control status signal sent from the certification ECU (smart key ECU assembly) to detect a stuck on malfunction of the IG2 signal.

w/o Smart Key System:

  • The hybrid vehicle control ECU assembly compares the IG2 signal to the IG switch signal sent from the main body ECU (multiplex network body ECU) via CAN communication to detect a stuck on malfunction of the IG2 signal.

HINT:

If DTC P253012 is stored, the vehicle will turn off (READY off).

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

MIL

Warning Indicate

P253012

IG2 Signal Circuit Short to Auxiliary Battery

The IG2 signal of the hybrid vehicle control ECU assembly and the IG switch signal sent from the main body ECU (multiplex network body ECU) do not match.

(1 trip detection logic)
  • Auxiliary battery
  • Certification ECU (smart key ECU assembly) (w/ Smart Key System)
  • Hybrid vehicle control ECU assembly
  • ECM
  • IG2 NO. 1 relay
  • Wire harness or connector
  • Fusible link block assembly
  • Instrument panel junction block assembly

Does not come on

Master Warning:

Comes on

CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click here 2019 - 2024 MY RAV4 HV [02/2019 -        ]; HYBRID / BATTERY CONTROL: HYBRID CONTROL SYSTEM (for AWD with NICKEL METAL HYDRIDE BATTERY): UTILITY

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON and turn the Techstream on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  4. Turn the ignition switch off and wait for 2 minutes or more.
  5. Turn the ignition switch to ON and wait for 15 seconds or more.
  6. Turn the ignition switch off and wait for 2 minutes or more.
  7. Turn the ignition switch to ON and turn the Techstream on.
  8. Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.
  9. Check the DTC judgment result.

    HINT:

    • If the judgment result shows NORMAL, the system is normal.
    • If the judgment result shows ABNORMAL, the system has a malfunction.
    • If the judgment result shows INCOMPLETE, perform driving pattern again.

WIRING DIAGRAM

w/ Smart Key System:
w/o Smart Key System:

CAUTION / NOTICE / HINT

NOTICE:

Before replacing the certification ECU (smart key ECU assembly), refer to Registration.

Click here 2019 MY RAV4 HV [11/2018 - 10/2019]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function, HV Model): REGISTRATION 2020 - 2021 MY RAV4 HV [10/2019 - 12/2021]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function, HV Model): REGISTRATION 2022 - 2024 MY RAV4 HV [12/2021 -        ]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function, HV Model): REGISTRATION

PROCEDURE

1.

CHECK VEHICLE CONDITION

(a) Check the vehicle condition.

Result

Proceed to

w/ Smart Key System

A

w/o Smart Key System

B
B

GO TO STEP 11

A

2.

CHECK AUXILIARY BATTERY VOLTAGE

(a) Turn the ignition switch off and turn on the high beam headlights for 30 seconds. This will remove the surface charge from the auxiliary battery.

(b) Measure the auxiliary battery voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Condition

Specified Condition

Positive (+) auxiliary battery terminal - Negative (-) auxiliary battery terminal

20°C (68°F), Ignition switch off

12.0 V or higher
OK

GO TO STEP 4

NG

3.

CHARGE OR REPLACE AUXILIARY BATTERY

(a) Charge or replace the auxiliary battery.

NEXT

4.

CLEAR DTC

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(c) Turn the Techstream on.

(d) Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

(e) Clear the DTCs.

Powertrain > Hybrid Control > Clear DTCs

(f) Turn the ignition switch off.

NEXT

5.

CHECK DTC OUTPUT (HYBRID CONTROL)

(a) Turn the ignition switch to ON and wait for 15 seconds or more.

(b) Turn the ignition switch off and wait for 2 minutes or more.

(c) Connect the Techstream to the DLC3.

(d) Turn the ignition switch to ON.

(e) Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

Powertrain > Hybrid Control > Trouble Codes

(f) Check for DTCs.

Result

Proceed to

P253012 is output.

A

P253012 is not output.

B

(g) Turn the ignition switch off.

B

CHECK FOR INTERMITTENT PROBLEMS

A

6.

CHECK DTC OUTPUT (HYBRID CONTROL)

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(c) Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

(d) Check for DTCs.

Powertrain > Hybrid Control > Trouble Codes

Result

Proceed to

U012987, U014087, U015187, U016487, U110787 or U117087 is output

A

Other than above

B

(e) Turn the ignition switch off.

B

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) 2019 MY RAV4 RAV4 HV [02/2019 - 10/2019]; THEFT DETERRENT / KEYLESS ENTRY: CERTIFICATION ECU: REMOVAL 2020 MY RAV4 RAV4 HV [10/2019 - 08/2020]; THEFT DETERRENT / KEYLESS ENTRY: CERTIFICATION ECU: REMOVAL 2021 MY RAV4 RAV4 HV [08/2020 - 12/2021]; THEFT DETERRENT / KEYLESS ENTRY: CERTIFICATION ECU: REMOVAL 2022 MY RAV4 RAV4 HV [12/2021 - 10/2022]; THEFT DETERRENT / KEYLESS ENTRY: CERTIFICATION ECU: REMOVAL 2023 MY RAV4 RAV4 HV [10/2022 - 10/2023]; THEFT DETERRENT / KEYLESS ENTRY: CERTIFICATION ECU: REMOVAL 2024 MY RAV4 RAV4 HV [10/2023 -        ]; THEFT DETERRENT / KEYLESS ENTRY: CERTIFICATION ECU: REMOVAL

A

7.

CHECK HYBRID VEHICLE CONTROL ECU ASSEMBLY

(a) Disconnect the A31 hybrid vehicle control ECU assembly connectors.

*a

Front view of wire harness connector

(to Hybrid Vehicle Control ECU Assembly)

(b) Measure the voltage according to the value(s) in the table below.

Condition:

Tester Connection

Condition

A31-35 (IG2) - A31-12 (E01)

Ignition switch off

(c) Reconnect the A31 hybrid vehicle control ECU assembly connectors.

Result

Proceed to

9 V or higher

A

Below 9 V

B
B

REPLACE HYBRID VEHICLE CONTROL ECU ASSEMBLY 2019 MY RAV4 HV [02/2019 - 10/2019]; HYBRID / BATTERY CONTROL: HYBRID VEHICLE CONTROL ECU: REMOVAL 2020 MY RAV4 HV [10/2019 - 08/2020]; HYBRID / BATTERY CONTROL: HYBRID VEHICLE CONTROL ECU: REMOVAL 2021 MY RAV4 HV [08/2020 - 12/2021]; HYBRID / BATTERY CONTROL: HYBRID VEHICLE CONTROL ECU: REMOVAL 2022 MY RAV4 HV [12/2021 - 10/2022]; HYBRID / BATTERY CONTROL: HYBRID VEHICLE CONTROL ECU: REMOVAL 2023 MY RAV4 HV [10/2022 - 10/2023]; HYBRID / BATTERY CONTROL: HYBRID VEHICLE CONTROL ECU: REMOVAL 2024 MY RAV4 HV [10/2023 -        ]; HYBRID / BATTERY CONTROL: HYBRID VEHICLE CONTROL ECU: REMOVAL

A

8.

CHECK ECM

(a) Disconnect the A31 hybrid vehicle control ECU assembly connectors.

*a

Front view of wire harness connector

(to Hybrid Vehicle Control ECU Assembly)

(b) Disconnect the A24 ECM connector.

(c) Measure the voltage according to the value(s) in the table below.

Condition:

Tester Connection

Condition

A31-35 (IG2) - A31-12 (E01)

Ignition switch off

(d) Reconnect the A24 ECM connector.

(e) Reconnect the A31 hybrid vehicle control ECU assembly connectors.

Result

Proceed to

9 V or higher

A

Below 9 V

B
B

REPLACE ECM 2019 - 2020 MY RAV4 HV [02/2019 - 08/2020]; A25A-FXS (ENGINE CONTROL): ECM: REMOVAL 2021 MY RAV4 HV [08/2020 - 12/2021]; A25A-FXS (ENGINE CONTROL): ECM: REMOVAL 2022 MY RAV4 HV [12/2021 - 10/2022]; A25A-FXS (ENGINE CONTROL): ECM: REMOVAL 2023 MY RAV4 HV [10/2022 - 10/2023]; A25A-FXS (ENGINE CONTROL): ECM: REMOVAL 2024 MY RAV4 HV [10/2023 -        ]; A25A-FXS (ENGINE CONTROL): ECM: REMOVAL

A

9.

INSPECT RELAY (IG2 NO. 1)

(a) Remove the IG2 NO. 1 relay from the No. 1 engine room relay block and junction block assembly.

*1

No. 1 Engine Room Relay Block and Junction Block Assembly

*2

IG2 NO. 1 Relay

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

3 - 5

Auxiliary battery voltage not applied between terminals 1 and 2

10 kΩ or higher

Auxiliary battery voltage applied between terminals 1 and 2

Below 1 Ω

(c) Install the IG2 NO. 1 relay.

NG

REPLACE RELAY (IG2 NO. 1)
OK

10.

CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU ASSEMBLY - IG2 NO. 1 RELAY)

(a) Disconnect the A31 hybrid vehicle control ECU assembly connector.

(b) Remove the IG2 NO. 1 relay from the No. 1 engine room relay block and junction block assembly.

(c) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Condition

Specified Condition

A31-35 (IG2) - Body ground

Ignition switch off

1 V or less

*a

Front view of wire harness connector

(to Hybrid Vehicle Control ECU Assembly)

(d) Install the IG2 NO. 1 relay.

(e) Reconnect the A31 hybrid vehicle control ECU assembly connector.

OK

(a) Check for intermittent problems.

Click here CHECK FOR INTERMITTENT PROBLEMS

(1) Check the connection and terminal contact pressure of the connectors and wire harnesses between the hybrid vehicle control ECU assembly and the IG2 NO. 1 relay.

(2) When the ignition switch is ON (READY), jiggle the connectors and wire harnesses between the hybrid vehicle control ECU assembly and the IG2 NO. 1 relay.
NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.

CLEAR DTC

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(c) Turn the Techstream on.

(d) Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

(e) Clear the DTCs.

Powertrain > Hybrid Control > Clear DTCs

(f) Turn the ignition switch off.

NEXT

12.

CHECK DTC OUTPUT (HYBRID CONTROL)

(a) Turn the ignition switch to ON and wait for 15 seconds or more.

(b) Turn the ignition switch off and wait for 2 minutes or more.

(c) Connect the Techstream to the DLC3.

(d) Turn the ignition switch to ON.

(e) Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

Powertrain > Hybrid Control > Trouble Codes

(f) Check for DTCs.

Result

Proceed to

Only P253012 is output or P253012 and DTCs other than U014087 are also output.

A

U014087 is output.

B

DTCs other than P253012 or U014087 are output.

C

No DTCs are output.

D

(g) Turn the ignition switch off.

B

GO TO DTC CHART (U014087) 2019 - 2021 MY RAV4 HV [02/2019 - 12/2021]; HYBRID / BATTERY CONTROL: HYBRID CONTROL SYSTEM (for AWD with NICKEL METAL HYDRIDE BATTERY): U010087,...,U117087; Lost Communication with ECM/PCM "A" Missing Message 2022 - 2024 MY RAV4 HV [12/2021 -        ]; HYBRID / BATTERY CONTROL: HYBRID CONTROL SYSTEM (for AWD with NICKEL METAL HYDRIDE BATTERY): U010087,...,U117087; Lost Communication with ECM/PCM "A" Missing Message

C

GO TO DTC CHART (HYBRID CONTROL SYSTEM) 2019 - 2020 MY RAV4 HV [02/2019 - 06/2020]; HYBRID / BATTERY CONTROL: HYBRID CONTROL SYSTEM (for AWD with NICKEL METAL HYDRIDE BATTERY): DIAGNOSTIC TROUBLE CODE CHART 2020 - 2021 MY RAV4 HV [06/2020 - 12/2021]; HYBRID / BATTERY CONTROL: HYBRID CONTROL SYSTEM (for AWD with NICKEL METAL HYDRIDE BATTERY): DIAGNOSTIC TROUBLE CODE CHART 2022 - 2024 MY RAV4 HV [12/2021 -        ]; HYBRID / BATTERY CONTROL: HYBRID CONTROL SYSTEM (for AWD with NICKEL METAL HYDRIDE BATTERY): DIAGNOSTIC TROUBLE CODE CHART

D

GO TO STEP 16

A

13.

CHECK FUSIBLE LINK BLOCK ASSEMBLY (DC/DC)

(a) Disconnect the cable from the negative (-) auxiliary battery terminal.

(b) Remove the fusible link block assembly (DC/DC).

*1

Fusible link block assembly

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

1G-1 - 1A-1

Always

Below 1 Ω
NG

REPLACE FUSIBLE LINK BLOCK ASSEMBLY (DC/DC)
OK

14.

CHECK WIRE HARNESS AND CONNECTOR (IG1 NO. 1 RELAY - POWER SOURCE CIRCUIT)

(a) Disconnect the instrument panel junction block assembly connector.

(b) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Switch Condition

Specified Condition

4K-1 - Body ground

Ignition switch off

11 to 14 V

*a

Front view of wire harness connector

(Instrument Panel Junction Block Assembly)

(c) Connect the instrument panel junction block assembly connector.

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

15.

CHECK WIRE HARNESS AND CONNECTOR (IG1 NO. 1 RELAY - BODY GROUND)

(a) Disconnect the 4D instrument panel junction block assembly connector.

(b) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Switch Condition

Specified Condition

4D-3 - Body ground

Ignition switch off

Below 1 Ω

*a

Front view of wire harness connector

(to Instrument Panel Junction Block Assembly)

(c) Connect the 4D instrument panel junction block assembly connector.

OK

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (IG1 NO. 1 RELAY)
NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

16.

CHECK DTC OUTPUT (HYBRID CONTROL)

(a) Turn the ignition switch to ON and wait for 15 seconds or more.

(b) Turn the ignition switch off and wait for 2 minutes or more.

(c) Connect the Techstream to the DLC3.

(d) Turn the ignition switch to ON.

(e) Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

Powertrain > Hybrid Control > Trouble Codes

(f) Check for DTCs.

Result

Proceed to

P253012 is output.

A

P253012 is not output.

B

(g) Turn the ignition switch off.

B

CHECK FOR INTERMITTENT PROBLEMS

A

17.

CHECK HYBRID VEHICLE CONTROL ECU ASSEMBLY

(a) Disconnect the A31 hybrid vehicle control ECU assembly connectors.

*a

Front view of wire harness connector

(to Hybrid Vehicle Control ECU Assembly)

(b) Measure the voltage according to the value(s) in the table below.

Condition:

Tester Connection

Condition

A31-35 (IG2) - A31-12 (E01)

Ignition switch off

(c) Reconnect the A31 hybrid vehicle control ECU assembly connectors.

Result

Proceed to

9 V or higher

A

Below 9 V

B
B

REPLACE HYBRID VEHICLE CONTROL ECU ASSEMBLY 2019 MY RAV4 HV [02/2019 - 10/2019]; HYBRID / BATTERY CONTROL: HYBRID VEHICLE CONTROL ECU: REMOVAL 2020 MY RAV4 HV [10/2019 - 08/2020]; HYBRID / BATTERY CONTROL: HYBRID VEHICLE CONTROL ECU: REMOVAL 2021 MY RAV4 HV [08/2020 - 12/2021]; HYBRID / BATTERY CONTROL: HYBRID VEHICLE CONTROL ECU: REMOVAL 2022 MY RAV4 HV [12/2021 - 10/2022]; HYBRID / BATTERY CONTROL: HYBRID VEHICLE CONTROL ECU: REMOVAL 2023 MY RAV4 HV [10/2022 - 10/2023]; HYBRID / BATTERY CONTROL: HYBRID VEHICLE CONTROL ECU: REMOVAL 2024 MY RAV4 HV [10/2023 -        ]; HYBRID / BATTERY CONTROL: HYBRID VEHICLE CONTROL ECU: REMOVAL

A

18.

CHECK ECM

(a) Disconnect the A31 hybrid vehicle control ECU assembly connectors.

*a

Front view of wire harness connector

(to Hybrid Vehicle Control ECU Assembly)

(b) Disconnect the A24 ECM connector.

(c) Measure the voltage according to the value(s) in the table below.

Condition:

Tester Connection

Condition

A31-35 (IG2) - A31-12 (E01)

Ignition switch off

(d) Reconnect the A24 ECM connector.

(e) Reconnect the A31 hybrid vehicle control ECU assembly connectors.

Result

Proceed to

9 V or higher

A

Below 9 V

B
B

REPLACE ECM 2019 - 2020 MY RAV4 HV [02/2019 - 08/2020]; A25A-FXS (ENGINE CONTROL): ECM: REMOVAL 2021 MY RAV4 HV [08/2020 - 12/2021]; A25A-FXS (ENGINE CONTROL): ECM: REMOVAL 2022 MY RAV4 HV [12/2021 - 10/2022]; A25A-FXS (ENGINE CONTROL): ECM: REMOVAL 2023 MY RAV4 HV [10/2022 - 10/2023]; A25A-FXS (ENGINE CONTROL): ECM: REMOVAL 2024 MY RAV4 HV [10/2023 -        ]; A25A-FXS (ENGINE CONTROL): ECM: REMOVAL

A

19.

INSPECT RELAY (IG2 NO. 1)

(a) Remove the IG2 NO. 1 relay from the No. 1 engine room relay block and junction block assembly.

*1

No. 1 Engine Room Relay Block and Junction Block Assembly

*2

IG2 NO. 1 Relay

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

3 - 5

Auxiliary battery voltage not applied between terminals 1 and 2

10 kΩ or higher

Auxiliary battery voltage applied between terminals 1 and 2

Below 1 Ω

(c) Install the IG2 NO. 1 relay.

NG

REPLACE RELAY (IG2 NO. 1)
OK

20.

CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU ASSEMBLY - IG2 NO. 1 RELAY)

(a) Disconnect the A31 hybrid vehicle control ECU assembly connector.

(b) Remove the IG2 NO. 1 relay from the No. 1 engine room relay block and junction block assembly.

(c) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Condition

Specified Condition

A31-35 (IG2) - Body ground

Ignition switch off

1 V or less

*a

Front view of wire harness connector

(to Hybrid Vehicle Control ECU Assembly)

(d) Install the IG2 NO. 1 relay.

(e) Reconnect the A31 hybrid vehicle control ECU assembly connector.

OK

(a) Check for intermittent problems.

Click here CHECK FOR INTERMITTENT PROBLEMS

(1) Check the connection and terminal contact pressure of the connectors and wire harnesses between the hybrid vehicle control ECU assembly and the IG2 NO. 1 relay.

(2) When the ignition switch is ON (READY), jiggle the connectors and wire harnesses between the hybrid vehicle control ECU assembly and the IG2 NO. 1 relay.
NG

REPAIR OR REPLACE HARNESS OR CONNECTOR