| Last Modified: 01-30-2024 | 6.11:8.1.0 | Doc ID: RM100000001H3EE |
| Model Year Start: 2019 | Model: RAV4 HV | Prod Date Range: [02/2019 - ] |
| Title: HYBRID / BATTERY CONTROL: REAR MOTOR GENERATOR CONTROL SYSTEM: P0A6912,...,P0A6C1F; Drive Motor "B" Phase V Current(High Resolution) Circuit Short to Battery; 2019 - 2024 MY RAV4 HV [02/2019 - ] | ||
|
DTC |
P0A6912 |
Drive Motor "B" Phase V Current(High Resolution) Circuit Short to Battery |
|
DTC |
P0A6914 |
Drive Motor "B" Phase V Current(High Resolution) Circuit Short to Ground or Open |
|
DTC |
P0A691C |
Drive Motor "B" Phase V Current(High Resolution) Circuit Voltage Out of Range |
|
DTC |
P0A691F |
Drive Motor "B" Phase V Current(High Resolution) Circuit Intermittent |
|
DTC |
P0A6C12 |
Drive Motor "B" Phase W Current(High Resolution) Circuit Short to Battery |
|
DTC |
P0A6C14 |
Drive Motor "B" Phase W Current(High Resolution) Circuit Short to Ground or Open |
|
DTC |
P0A6C1C |
Drive Motor "B" Phase W Current(High Resolution) Circuit Voltage Out of Range |
|
DTC |
P0A6C1F |
Drive Motor "B" Phase W Current(High Resolution) Circuit Intermittent |
DESCRIPTION
The motor generator control ECU (MG ECU), which is built into the inverter with converter assembly, monitors its internal operation and will store DTCs if it detects a malfunction.
|
DTC No. |
Detection Item |
DTC Detection Condition |
Trouble Area |
MIL |
Warning Indicate |
|---|---|---|---|---|---|
|
P0A6912 |
Drive Motor "B" Phase V Current(High Resolution) Circuit Short to Battery |
Rear motor inverter phase V current sensor high resolution signal circuit (short to +B) (1 trip detection logic) |
|
Does not come on |
Master Warning: Comes on |
|
P0A6914 |
Drive Motor "B" Phase V Current(High Resolution) Circuit Short to Ground or Open |
Rear motor inverter phase V current sensor high resolution signal circuit (short to ground or open) (1 trip detection logic) |
|
Does not come on |
Master Warning: Comes on |
|
P0A691C |
Drive Motor "B" Phase V Current(High Resolution) Circuit Voltage Out of Range |
Rear motor inverter phase V current sensor high resolution signal circuit (out of range) (1 trip detection logic) |
|
Does not come on |
Master Warning: Comes on |
|
P0A691F |
Drive Motor "B" Phase V Current(High Resolution) Circuit Intermittent |
Out of range detected in rear motor inverter phase V current sensor when P0C7917, P0D3319, P1C5D19, P1C5F19 or P1C5E19 is stored. (1 trip detection logic) |
|
Does not come on |
Master Warning: Does not come on |
|
P0A6C12 |
Drive Motor "B" Phase W Current(High Resolution) Circuit Short to Battery |
Rear motor inverter phase W current sensor high resolution signal circuit (short to +B) (1 trip detection logic) |
|
Does not come on |
Master Warning: Comes on |
|
P0A6C14 |
Drive Motor "B" Phase W Current(High Resolution) Circuit Short to Ground or Open |
Rear motor inverter phase W current sensor high resolution signal circuit (short to ground or open) (1 trip detection logic) |
|
Does not come on |
Master Warning: Comes on |
|
P0A6C1C |
Drive Motor "B" Phase W Current(High Resolution) Circuit Voltage Out of Range |
Rear motor inverter phase W current sensor high resolution signal circuit (out of range) (1 trip detection logic) |
|
Does not come on |
Master Warning: Comes on |
|
P0A6C1F |
Drive Motor "B" Phase W Current(High Resolution) Circuit Intermittent |
Out of range detected in rear motor inverter phase W current sensor when P0C7917, P0D3319, P1C5D19, P1C5F19 or P1C5E19 is stored. (1 trip detection logic) |
|
Does not come on |
Master Warning: Does not come on |
CONFIRMATION DRIVING PATTERN
HINT:
After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Click here
![2019 - 2024 MY RAV4 HV [02/2019 - ]; HYBRID / BATTERY CONTROL: REAR MOTOR GENERATOR CONTROL SYSTEM: UTILITY](/t3Portal/stylegraphics/info.gif)
- Connect the Techstream to the DLC3.
- Turn the ignition switch to ON and turn the Techstream on.
- Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
- Turn the ignition switch off and wait for 2 minutes or more.
- Turn the ignition switch to ON and turn the Techstream on.
- With ignition switch ON and wait for 5 seconds or more.
- Enter the following menus: Powertrain / Rear Motor Generator / Utility / All Readiness.
-
Check the DTC judgment result.
HINT:
- If the judgment result shows NORMAL, the system is normal.
- If the judgment result shows ABNORMAL, the system has a malfunction.
- If the judgment result shows INCOMPLETE, perform driving pattern again.
CAUTION / NOTICE / HINT
CAUTION:
-
Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the service plug grip from HV battery.
- Inspecting the high-voltage system
- Disconnecting the low voltage connector of the inverter with converter assembly
- Disconnecting the low voltage connector of the HV battery
-
To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.
-
After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.
-
After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.
Click here
HINT:
Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.
*a
Without waiting for 10 minutes
NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click here
PROCEDURE
|
1. |
CHECK DTC OUTPUT (MOTOR GENERATOR) |
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Enter the following menus: Powertrain / Motor Generator / Trouble Codes.
(d) Check for DTCs.
Powertrain > Motor Generator > Trouble Codes
|
Result |
Proceed to |
|---|---|
|
P0A6912, P0A6914, P0A691C, P0A691F, P0A6C12, P0A6C14, P0A6C1C or P0A6C1F only is output, or DTCs except the ones in the table below are also output. |
A |
|
Any of the following DTCs including pending DTCs are also output. |
B |
|
Malfunction Content |
System |
Relevant DTC |
|
|---|---|---|---|
|
Power source circuit malfunction |
Motor generator control system |
P06B01C |
Generator Control Module Position Sensor REF Power Source Circuit Voltage Out of Range |
|
P06D61C |
Generator Control Module Offset Power Circuit Voltage Out of Range |
||
|
System malfunction |
Motor generator control system |
P0A7973 |
Drive Motor "B" Inverter Actuator Stuck Closed |
HINT:
-
P0A6912, P0A6914, P0A691C, P0A691F, P0A6C12, P0A6C14, P0A6C1C or P0A6C1F may be output as a result of the malfunctions indicated by the DTCs above.
- The chart above is listed in inspection order of priority.
- Check DTCs that are output at the same time by following the listed order. (The main cause of the malfunction can be determined without performing unnecessary inspections.)
(e) Turn the ignition switch off.
| B |
|
|
|
2. |
CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR) |
Click here
|
Result |
Proceed to |
|---|---|
|
OK |
A |
|
NG (The connector is not connected securely.) |
B |
|
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) |
C |
| A |
|
REPLACE INVERTER WITH CONVERTER ASSEMBLY
|
| B |
|
CONNECT SECURELY |
| C |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|