Last Modified: 01-30-2024 6.11:8.1.0 Doc ID: RM100000001G2BL
Model Year Start: 2019 Model: RAV4 Prod Date Range: [11/2018 - 08/2020]
Title: LIGHTING (EXT): LIGHTING SYSTEM (w/ Headlight ECU without AFS): DATA LIST / ACTIVE TEST; 2019 - 2020 MY RAV4 RAV4 HV [11/2018 - 08/2020]

DATA LIST / ACTIVE TEST

DATA LIST

NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

HINT:

Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(c) Turn the Techstream on.

(d) Enter the following menus:

(1) Body Electrical / Main Body / Data List.

(2) Body Electrical / HL AutoLeveling / Data List.

(3) Body Electrical / HL AutoLeveling (Sub) / Data List.

(4) Chassis / Steering Angle Sensor / Data List.

(5) Body Electrical / Combination Meter / Data List.

(6) w/ Automatic High Beam System:

Body Electrical / Front Recognition Camera (Front Lighting Control) / Data List.

(7) w/ Automatic High Beam System:

Chassis / Front Recognition Camera / Data List.

(e) Read the Data List according to the display on the Techstream.

Body Electrical > Main Body > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Auto High Beam Main Switch

Auto high beam switch signal*1

OFF or ON

OFF: Auto high beam switch not pressed

ON: Auto high beam switch pressed

-

Head Light SW (Head)

Light control switch HEAD position signal

OFF or ON

OFF: Light control switch not in HEAD position

ON: Light control switch in HEAD position

-

Insolation Amount of Solar Sensor RH

Solar sensor RH condition

0 to 51100 or SensorFail

Condition can be displayed

-

Insolation Amount of Solar Sensor LH

Solar sensor LH condition

0 to 51100 or SensorFail

Condition can be displayed

-

Light Sensor Illuminance

Light control sensor illuminance

0 to 8191 lx or SensorFail

Value is output according to ambient light level

-

Light Sensor Connection Status

Light control sensor connection status

OFF or ON

OFF: Automatic light control sensor has not been connected

ON: Automatic light control sensor connected or has been connected

-

Headlight Lighting Function

ECU which controls the lighting system

Main Body or Lighting Sys ECU

Main Body: Lighting system controlled by main body ECU (multiplex network body ECU)

Lighting Sys ECU: Lighting system is controlled by headlight ECU sub-assembly

-

Response Time

Delay timing of lighting the taillights when the automatic light control sensor detects brightness change

0.1 s or 1.0 s

Customize setting displayed

-

Sensitivity

Sensitivity of the automatic light control system

Light2, Light1, Normal, Dark1 or Dark2

Customize setting displayed

-

Disp Ex ON Sen

Ambient brightness level required to dim display lights (combination meter, navigation display, etc.)

Light2, Light1, Normal, Dark1 or Dark2

Customize setting displayed

-

Disp Ex OFF Sen

Ambient brightness level required to cancel dimming display lights (combination meter, navigation display, etc.)

Light2, Light1, Normal, Dark1 or Dark2

Customize setting displayed

-

Suggestion Service Function

Turns the suggestion service function on/off.

OFF, Only Parked or ON

Customize setting displayed

-

Auto H Beam STS0

Automatic high beam sensor current state*1

Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin or LIN Err

Condition can be displayed*2

If the value of this item is not as specified, the automatic high beam sensor system may be malfunctioning.

Auto H Beam STS1

Automatic high beam sensor state past 1*1

Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin or LIN Err

Condition can be displayed*2

Although this item is displayed on the Techstream, it is not applicable to this vehicle.

Auto H Beam STS2

Automatic high beam sensor state past 2*1

Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin or LIN Err

Condition can be displayed*2

Although this item is displayed on the Techstream, it is not applicable to this vehicle.

Auto H Beam STS3

Automatic high beam sensor state past 3*1

Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin or LIN Err

Condition can be displayed*2

Although this item is displayed on the Techstream, it is not applicable to this vehicle.

Auto H Beam STS4

Automatic high beam sensor state past 4*1

Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin or LIN Err

Condition can be displayed*2

Although this item is displayed on the Techstream, it is not applicable to this vehicle.

Auto H Beam STS5

Automatic high beam sensor state past 5*1

Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin or LIN Err

Condition can be displayed*2

Although this item is displayed on the Techstream, it is not applicable to this vehicle.

Auto H Beam STS6

Automatic high beam sensor state past 6*1

Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin or LIN Err

Condition can be displayed*2

Although this item is displayed on the Techstream, it is not applicable to this vehicle.

Auto H Beam STS7

Automatic high beam sensor state past 7*1

Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin or LIN Err

Condition can be displayed*2

Although this item is displayed on the Techstream, it is not applicable to this vehicle.

Tail Remind Buzzer Function

Setting of the tail remind buzzer function on/off

OFF or ON

Customize setting displayed

-

Auto Light Off Timing Setting

Sets the timing to turn off the taillights when the light control switch is in the TAIL or HEAD position.

IG OFF or Door Open

Customize setting displayed

-

The Number of DTC

Number of trouble codes

0 to 255

Number of stored DTCs displayed

-
  • *1: w/ Automatic High Beam System

HINT:

*2: The details of each value of the Range are as follows:

Display Value

Condition

Control Condition

Diagnostic Note

Undetec

Automatic high beam sensor being initialized

Control suspended (low beam headlights illuminated)

-

CAM NA

Automatic high beam sensor temporarily disabled due to high temperature, unclear image (due to dirt, fog, etc.), etc.

Control suspended (low beam headlights illuminated)

-

No sens

No lights detected

High beam headlights illuminated

Only when vehicle speed within operation speed range

Hlight

Headlights of oncoming vehicle, etc. detected

Low beam headlights illuminated

Only when vehicle speed within operation speed range

Taillgt

Taillights preceding vehicle, etc. detected

Low beam headlights illuminated

Only when vehicle speed within operation speed range

Speed

No lights detected and vehicle speed below operation speed

Low beam headlights illuminated

-

Daytime

Bright light detected

Low beam headlights illuminated

-

Village

Streetlights, etc. detected

Low beam headlights illuminated

Only when vehicle speed within operation speed range

Delay

Changing between low beams and high beams

Changing between low beams and high beams

Only when vehicle speed within operation speed range

SAE Mod

Not applicable

-

-

Malfunc

Aim Lmt

Undefin

LIN Err

Body Electrical > HL AutoLeveling > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Headlight Low Beam State

Low beam headlight LH state

OFF or ON

OFF: Low beam headlight LH off

ON: Low beam headlight LH on

-

Headlight High Beam State

High beam headlight LH state

OFF or ON

OFF: High beam headlight LH off

ON: High beam headlight LH on

-

+B

Headlight ECU sub-assembly LH IG power supply voltage value

0.00 to 19.75 V

11.00 to 14.00 V

-

Height Sens Pw Supply Val

Rear height control sensor sub-assembly LH power supply value

0.00 to 5.00 V

4.61 to 5.00 V

-

Rr Height Sens Signal Val

Rear height control sensor sub-assembly LH signal value

0.00 to 5.00 V

0.50 to 4.50 V

Value changes according to vehicle height

Front Right Wheel Speed Value

Front right wheel speed

0.00 to 260.00 km/h (162.00 mph)

Condition can be displayed

-

Front Left Wheel Speed Value

Front left wheel speed

0.00 to 260.00 km/h (162.00 mph)

Condition can be displayed

-

Vehicle Speed

Vehicle speed

0.00 to 260.00 km/h (162.00 mph)

Condition can be displayed

-

Rear Height Adjust Value

Rear height adjustment offset value

0 to 1023

Actual rear height adjustment normal value is displayed (If there is a malfunction, no value is displayed)

-

Rear Height Adjust Valid Flag

Rear height adjustment range

Inval or Valid

Inval: Rear height control sensor sub-assembly LH value out of normal range

Valid: Rear height control sensor sub-assembly LH value within normal range

-

Init Writing Count

Number of times initialization performed

0 to 255

Number of times initialization performed

-

Steering Sensor Signal

Steering sensor signal value

-384.0 to 382.5 deg

Changes according to the operation of the steering wheel

Turning left: Increases

Turning right: Decreases

Steering Sensor Center Position

Steering sensor center position

-3072.0 to 3070.5 deg

0.0 deg (tires straight ahead)

-

+B Voltage Value

Headlight ECU sub-assembly LH +B power supply voltage value

0.00 to 19.75 V

11.00 to 14.00 V

-

Leveling Motor Target Position

Headlight leveling motor target position

0.0 to 102.3%

10.0 to 90.0%

-

Steering Sensor Initialization Status

Steering sensor initialization state

Incomplete or Completed

Incomplete: Steering sensor zero point calibration incomplete

Completed: Steering sensor zero point calibration complete

-

Clearance Light State

Clearance light LH state

OFF or ON

OFF: Clearance light LH off

ON: Clearance light LH on

-

Right Cornering Light/Front Side Illuminate Light State

Cornering light RH/front side illuminate light RH state

OFF or ON

OFF: Cornering light RH/front side illuminate light RH off

ON: Cornering light RH/front side illuminate light RH on

Although this item is displayed on the Techstream, it is not applicable to this vehicle.

Left Cornering Light/Front Side Illuminate Light State

Cornering light LH/front side illuminate light LH state

OFF or ON

OFF: Cornering light LH/front side illuminate light LH off

ON: Cornering light LH/front side illuminate light LH on

Although this item is displayed on the Techstream, it is not applicable to this vehicle.

DRL Operating State

Daytime running light LH state

OFF or ON

OFF: Daytime running light LH off

ON: Daytime running light LH on

-

Number Of Trouble Codes

Number of trouble codes

0 to 255

Number of stored DTCs displayed

-

Body Electrical > HL AutoLeveling (Sub) > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Headlight Low Beam State

Low beam headlight RH state

OFF or ON

OFF: Low beam headlight RH off

ON: Low beam headlight RH on

-

Headlight High Beam State

High beam headlight RH state

OFF or ON

OFF: High beam headlight RH off

ON: High beam headlight RH on

-

Clearance Light State

Clearance light RH state

OFF or ON

OFF: Clearance light RH off

ON: Clearance light RH on

-

DRL State(DRL Operating State)

Daytime running light RH state

OFF or ON

OFF: Daytime running light RH off

ON: Daytime running light RH on

-

+B

Headlight ECU sub-assembly RH IG power supply voltage value

0.00 to 19.75 V

11.00 to 14.00 V

-

+B Voltage Value

Headlight ECU sub-assembly RH +B power supply voltage value

0.00 to 19.75 V

11.00 to 14.00 V

-

Number Of Trouble Codes

Number of trouble codes

0 to 255

Number of stored DTCs displayed

-

Chassis > Steering Angle Sensor > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Light OFF Switch

Light control switch off position signal

OFF or ON

OFF: Light control switch not in off position

ON: Light control switch in off position

-

Auto Light Switch

Light control switch AUTO position signal

OFF or ON

OFF: Light control switch not in AUTO position

ON: Light control switch in AUTO position

-

Head Light Switch (Tail)

Light control switch TAIL position signal

OFF or ON

OFF: Light control switch not in TAIL position

ON: Light control switch in TAIL position

-

Head Light Switch (Head)

Light control switch HEAD position signal

OFF or ON

OFF: Light control switch not in HEAD position

ON: Light control switch in HEAD position

-

High Beam Main Switch

Dimmer switch High position signal

OFF or ON

OFF: Dimmer switch not in High position

ON: Dimmer switch in High position

-

Passing Light Switch

Dimmer switch Flash position (pass) signal

OFF or ON

OFF: Dimmer switch not in Flash position

ON: Dimmer switch in Flash position

-

Auto High Beam Main Switch

Auto high beam switch signal

OFF or ON

OFF: Auto high beam switch off

ON: Auto high beam switch on

Although the item is displayed on the Techstream, it is not applicable to the vehicle.

Turn Signal Switch (Right)

Turn signal switch (right turn position) signal

OFF or ON

OFF: Turn signal switch not in right turn position

ON: Turn signal switch in right turn position

-

Turn Signal Switch (Left)

Turn signal switch (left turn position) signal

OFF or ON

OFF: Turn signal switch not in left turn position

ON: Turn signal switch in left turn position

-

Cornering Light/Front Side Illuminate Light Switch

Turn signal switch (full turn) signal

OFF or ON

OFF: Turn signal switch not in left or right full turn position

ON: Turn signal switch in left or right full turn position

-

Front Fog Light Switch

Front fog light switch signal

OFF or ON

OFF: Fog light switch in OFF position

ON: Fog light switch in Fr position

w/ Front Fog Light

Rear Fog Light/Bad Weather Switch

Rear fog light switch signal

OFF or ON

OFF: Fog light switch in OFF position

ON: Fog light switch in Rr position

Although the item is displayed on the Techstream, it is not applicable to the vehicle.

Automatic Light Equipped Info

Automatic light control system specification information

Unknown, With or Without

Unknown: Specification not stored

With: Automatic light control system equipped

Without: Automatic light control system not equipped

-

Bad Weather Mode Equipped Info

Bad weather specification information

Unknown, Without or With

Unknown: Specification not stored

Without: Bad weather specification not equipped

With: Bad weather specification equipped

Although the item is displayed on the Techstream, it is not applicable to the vehicle.

The Number of DTCs

Number of trouble codes

0 to 255

Number of stored DTCs displayed

-

Body Electrical > Combination Meter > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Hazard Flasher Switch

Hazard warning signal switch signal

OFF or ON

OFF: Hazard warning signal switch off

ON: Hazard warning signal switch on

-

Lane Change Flashing Times Adjust

Condition of the lane change flashing times

OFF, 3, 4, 5, 6 or 7

Customize setting displayed

-

w/ Automatic High Beam System:

Body Electrical > Front Recognition Camera (Front Lighting Control) > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Total Distance Traveled

Actual driving distance

0 to 16777215

Roughly the same as the actual driving distance

-

Total Distance Traveled - Unit

Actual driving distance unit

km or mile

Displays the current actual driving distance unit

-

AHB/AHS Information

Lighting system state

unknown, AHB or AHS

Displays lighting system state

-

w/ Automatic High Beam System:

Chassis > Front Recognition Camera > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Front Recognition Camera High Temperature 2

Whether high temperature malfunction of forward recognition camera exists or not

Not High Temperature or High Temperature

Not High Temperature: Approximately 65°C (149°F) or less

High Temperature: Approximately 65°C (149°F) or higher

If this item is "High Temperature", the automatic high beam system will be temporarily unavailable. If this does not improve even if the inside of the vehicle is left cooled for at least 10 minutes, the forward recognition camera may be malfunctioning.

HINT:

In summertime, the windshield glass may reach 100°C (212°F) or higher

ACTIVE TEST

HINT:

Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(c) Turn the Techstream on.

(d) Enter the following menus:

(1) Body Electrical / Main Body / Active Test.

(2) Body Electrical / HL AutoLeveling / Active Test.

(3) Body Electrical / HL AutoLeveling (Sub) / Active Test.

(4) Body Electrical / Combination Meter / Active Test.

(e) Perform the Active Test according to the display on the Techstream.

Body Electrical > Main Body > Active Test

Tester Display

Measurement Item

Control Range

Diagnostic Note

Daytime Running Light

Daytime running lights

OFF or ON

-

Taillight Relay

Taillight relay

OFF or ON

-

Headlight Relay

Low beam headlights

OFF or ON

-

Head Light Hi

High beam headlights

OFF or ON

-

Front Fog Light Relay

Front fog light relay

OFF or ON
  • w/ Front Fog Light
  • Light control switch in TAIL position

Rear Fog Light Relay

Rear fog light relay

OFF or ON

Although this item is displayed on the Techstream, it is not applicable to this vehicle.

Dimmer Signal

Dimmer signal

OFF or ON

State where circumference illumination is bright

Automatic High Beam Switch Light

Auto high beam switch indicator light

OFF or ON

w/ Automatic High Beam System

Body Electrical > HL AutoLeveling > Active Test

Tester Display

Measurement Item

Control Range

Diagnostic Note

Drive The Leveling Motor

Headlight leveling motor upward or downward operation

Stop, Down or Up

Perform the Active Test with the ignition switch ON (READY)*1 or engine started*2 and vehicle stopped

Headlight Leveling Indicator

"Headlight System Malfunction Visit Your Dealer" display

OFF or ON

-

Clearance Light

Clearance lights

OFF or ON

-

Headlight Low Beam

Low beam headlights

OFF or ON

-

Headlight High Beam

High beam headlights

OFF or ON

-

Daytime Running Light

Daytime running lights

OFF or ON

-

Cornering Light/Front Side Illuminate Light

Cornering light/front side illuminate light

OFF or ON

Although this item is displayed on the Techstream, it is not applicable to this vehicle.
  • *1: for HV Model
  • *2: for Gasoline Model

Body Electrical > HL AutoLeveling (Sub) > Active Test

Tester Display

Measurement Item

Control Range

Diagnostic Note

Clearance Light

Clearance lights

OFF or ON

-

Headlight Low Beam

Low beam headlights

OFF or ON

-

Headlight High Beam

High beam headlights

OFF or ON

-

Daytime Running Light

Daytime running lights

OFF or ON

-

Cornering Light/Front Side Illuminate Light

Cornering light/front side illuminate light

OFF or ON

Although this item is displayed on the Techstream, it is not applicable to this vehicle.

Body Electrical > Combination Meter > Active Test

Tester Display

Measurement Item

Control Range

Diagnostic Note

Automatic High Beam Indicator (Green)

Automatic high beam indicator

OFF or ON

w/ Automatic High Beam System