Last Modified: 01-30-2024 6.11:8.1.0 Doc ID: RM100000001G218
Model Year Start: 2019 Model: RAV4 HV Prod Date Range: [11/2018 -           ]
Title: THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function, HV Model): Power Source Mode does not Change to ON (IG); 2019 - 2024 MY RAV4 HV [11/2018 -        ]

Power Source Mode does not Change to ON (IG)

DESCRIPTION

If the power switch is pressed with the electrical key transmitter sub-assembly in the cabin, the certification ECU (smart key ECU assembly) receives a signal and changes the power source mode.

Related Data List and Active Test Items

Problem Symptom

Data List and Active Test

Power source mode does not change to on (IG) but does change to on (ACC)

Power Source Control

  • Power Supply Condition
  • IG Relay Monitor (Inside)
  • IG Relay Monitor (Outside)

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

  • When using the Techstream with the power switch off, connect the Techstream to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the Techstream and the vehicle begins. Then select the vehicle type under manual mode and enter the following menus: Body Electrical / Smart Key. While using the Techstream, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the Techstream and the vehicle.
  • Make sure that no DTCs are output. If any DTCs are output, proceed to Diagnostic Trouble Code Chart.
  • If the smart key system (for Start Function) has been canceled, enable the system before performing troubleshooting.

    Click here 2019 MY RAV4 HV [11/2018 - 02/2019]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Entry Function, HV Model): CUSTOMIZE PARAMETERS 2019 - 2020 MY RAV4 HV [02/2019 - 08/2020]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Entry Function, HV Model): CUSTOMIZE PARAMETERS 2021 - 2022 MY RAV4 HV [08/2020 - 10/2022]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Entry Function, HV Model): CUSTOMIZE PARAMETERS 2023 MY RAV4 HV [10/2022 - 10/2023]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Entry Function, HV Model): CUSTOMIZE PARAMETERS 2024 MY RAV4 HV [10/2023 -        ]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Entry Function, HV Model): CUSTOMIZE PARAMETERS

  • Inspect the fuses of circuits related to this system before performing the following procedure.
  • Before replacing the certification ECU (smart key ECU assembly), refer to the Registration.

    Click here 2019 MY RAV4 HV [11/2018 - 10/2019]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function, HV Model): REGISTRATION 2020 - 2021 MY RAV4 HV [10/2019 - 12/2021]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function, HV Model): REGISTRATION 2022 - 2024 MY RAV4 HV [12/2021 -        ]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function, HV Model): REGISTRATION

  • After completing repairs, confirm that the problem does not recur.
  • After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".

PROCEDURE

1.

CHECK FOR DTC

(a) Connect the Techstream to the DLC3.

(b) Turn the power switch on (IG).

(c) Turn the Techstream on.

(d) Enter the following menus: Body Electrical / Smart Key, Power Source Control / Trouble Codes.

(e) Check for DTCs.

Body Electrical > Smart Key > Trouble Codes

Body Electrical > Power Source Control > Trouble Codes

Result

Proceed to

DTCs are not output

A

Smart key system (for Start Function) DTCs are output

B

B

GO TO DIAGNOSTIC TROUBLE CODE CHART 2019 MY RAV4 HV [11/2018 - 02/2019]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Entry Function, HV Model): DIAGNOSTIC TROUBLE CODE CHART 2019 - 2024 MY RAV4 HV [02/2019 -        ]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Entry Function, HV Model): DIAGNOSTIC TROUBLE CODE CHART

A

2.

CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

(a) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Switch Condition

Specified Condition

G54-17 (IG1D) - Body ground

Power switch on (ACC) → Power switch on (IG)

1 V or less → 9 V or higher

*a

Component with harness connected

(Certification ECU (Smart Key ECU Assembly))

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) 2019 MY RAV4 RAV4 HV [11/2018 - 02/2019]; THEFT DETERRENT / KEYLESS ENTRY: CERTIFICATION ECU: REMOVAL 2019 MY RAV4 RAV4 HV [02/2019 - 10/2019]; THEFT DETERRENT / KEYLESS ENTRY: CERTIFICATION ECU: REMOVAL 2020 MY RAV4 RAV4 HV [10/2019 - 08/2020]; THEFT DETERRENT / KEYLESS ENTRY: CERTIFICATION ECU: REMOVAL 2021 MY RAV4 RAV4 HV [08/2020 - 12/2021]; THEFT DETERRENT / KEYLESS ENTRY: CERTIFICATION ECU: REMOVAL 2022 MY RAV4 RAV4 HV [12/2021 - 10/2022]; THEFT DETERRENT / KEYLESS ENTRY: CERTIFICATION ECU: REMOVAL 2023 MY RAV4 RAV4 HV [10/2022 - 10/2023]; THEFT DETERRENT / KEYLESS ENTRY: CERTIFICATION ECU: REMOVAL 2024 MY RAV4 RAV4 HV [10/2023 -        ]; THEFT DETERRENT / KEYLESS ENTRY: CERTIFICATION ECU: REMOVAL

OK

3.

CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY), POWER SUPPLY AND BODY GROUND)

(a) Disconnect the G54 certification ECU (smart key ECU assembly) connector.

(b) Disconnect the 4A, 4D and 4L instrument panel junction block assembly connectors.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

G54-17 (IG1D) - 4A-30

Always

Below 1 Ω

4D-3 - Body ground

Always

Below 1 Ω

G54-17 (IG1D) or 4A-30 - Other terminals and body ground

Always

10 kΩ or higher

(d) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Condition

Specified Condition

4A-17 - Body ground

Always

11 to 14 V

4L-1 - Body ground

Always

11 to 14 V

(e) Reconnect the G54 certification ECU (smart key ECU assembly) connector.

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

4.

CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

*a

Component without harness connected

(Instrument Panel Junction Block Assembly)

-

-

(a) Remove the instrument panel junction block assembly.

Click here 2019 MY RAV4 RAV4 HV [11/2018 - 02/2019]; POWER DISTRIBUTION: MAIN BODY ECU: REMOVAL 2019 MY RAV4 RAV4 HV [02/2019 - 10/2019]; POWER DISTRIBUTION: MAIN BODY ECU: REMOVAL 2020 MY RAV4 RAV4 HV [10/2019 - 08/2020]; POWER DISTRIBUTION: MAIN BODY ECU: REMOVAL 2021 MY RAV4 RAV4 HV [08/2020 - 12/2021]; POWER DISTRIBUTION: MAIN BODY ECU: REMOVAL 2022 MY RAV4 RAV4 HV [12/2021 - 10/2022]; POWER DISTRIBUTION: MAIN BODY ECU: REMOVAL 2023 MY RAV4 RAV4 HV [10/2022 - 10/2023]; POWER DISTRIBUTION: MAIN BODY ECU: REMOVAL 2024 MY RAV4 RAV4 HV [10/2023 -        ]; POWER DISTRIBUTION: MAIN BODY ECU: REMOVAL

(b) Reconnect the instrument panel junction block assembly connectors.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

4A-17 - 4F-13

Always

Below 1 Ω

(d) Connect a positive (+) lead from the auxiliary battery to terminal 4A-17.

(e) Connect a negative (-) lead from the auxiliary battery to terminal 4D-3.

(f) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

4K-1 - 4D-31

Always

Below 1 Ω

4K-1 - 4F-2

Always

Below 1 Ω

4L-1 - 4F-15

Always

Below 1 Ω

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY 2019 MY RAV4 RAV4 HV [11/2018 - 02/2019]; POWER DISTRIBUTION: MAIN BODY ECU: REMOVAL 2019 MY RAV4 RAV4 HV [02/2019 - 10/2019]; POWER DISTRIBUTION: MAIN BODY ECU: REMOVAL 2020 MY RAV4 RAV4 HV [10/2019 - 08/2020]; POWER DISTRIBUTION: MAIN BODY ECU: REMOVAL 2021 MY RAV4 RAV4 HV [08/2020 - 12/2021]; POWER DISTRIBUTION: MAIN BODY ECU: REMOVAL 2022 MY RAV4 RAV4 HV [12/2021 - 10/2022]; POWER DISTRIBUTION: MAIN BODY ECU: REMOVAL 2023 MY RAV4 RAV4 HV [10/2022 - 10/2023]; POWER DISTRIBUTION: MAIN BODY ECU: REMOVAL 2024 MY RAV4 RAV4 HV [10/2023 -        ]; POWER DISTRIBUTION: MAIN BODY ECU: REMOVAL

OK

5.

CHECK HARNESS AND CONNECTOR (IG1 NO. 1 RELAY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY, POWER SUPPLY AND BODY GROUND)

(a) Disconnect the 4F instrument panel junction block assembly connector.

(b) Remove the IG2 NO.1 relay.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

4F-13 - IG2 NO.1 relay installation terminal 1

Always

Below 1 Ω

IG2 NO.1 relay installation terminal 2 - Body ground

Always

Below 1 Ω

4F-13 or IG2 NO.1 relay installation terminal 1 - Other terminals and body ground

Always

10 kΩ or higher

(d) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Condition

Specified Condition

IG2 NO.1 relay installation terminal 5 - Body ground

Always

11 to 14 V

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

6.

INSPECT IG2 NO. 1 RELAY

(a) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

3 - 5

Auxiliary battery voltage applied between terminals 1 and 2

Below 1 Ω

Auxiliary battery voltage not applied between terminals 1 and 2

10 kΩ or higher

*1

IG2 NO. 1 Relay

OK

USE SIMULATION METHOD TO CHECK

NG

REPLACE IG2 NO. 1 RELAY