Last Modified: 01-30-2024 6.11:8.1.0 Doc ID: RM100000001G217
Model Year Start: 2019 Model: RAV4 HV Prod Date Range: [11/2018 - 06/2020]
Title: THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function, HV Model): Power Source Mode does not Change to ON (IG and ACC); 2019 - 2020 MY RAV4 HV [11/2018 - 06/2020]

Power Source Mode does not Change to ON (IG and ACC)

DESCRIPTION

When the power switch cannot be turned on (ACC) or on (IG), there may be a malfunction in interior certification, or the ACC relay or IG relay system. If interior certification does not succeed, the certification ECU (smart key ECU assembly) may be malfunctioning, or communication may not be possible between the No. 1 indoor electrical key antenna assembly (front floor) or No. 1 indoor electrical key antenna assembly (rear floor), the electrical key transmitter sub-assembly, and the door control receiver.

When the electrical key transmitter sub-assembly is brought into the cabin, the key ID code sent from the electrical key transmitter sub-assembly and the key ID code stored in the certification ECU (smart key ECU assembly) are certified. If these codes do not match and certification fails, the power switch cannot be turned on (ACC) or on (IG).

When the door is unlocked and the electrical key transmitter sub-assembly is brought into the cabin, the certification ECU (smart key ECU assembly) activates the indoor electrical key antenna and forms a detection area. When the electrical key transmitter sub-assembly is recognized inside the detection area, it returns the key ID code. This is received by the door control receiver, which then sends it to the certification ECU (smart key ECU assembly).

Related Data List and Active Test Items

Problem Symptom

Data List and Active Test

Power source mode does not change to on (IG) or on (ACC)

Power Source Control

  • Start Switch1
  • Start Switch2
  • IG Relay Monitor (Inside)
  • ACC Relay Monitor
  • IG Relay Monitor (Outside)
  • Latch Circuit
  • Power Supply Condition

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

  • When using the Techstream with the power switch off, connect the Techstream to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the Techstream and the vehicle begins. Then select the vehicle type under manual mode and enter the following menus: Body Electrical / Smart Key. While using the Techstream, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the Techstream and the vehicle.
  • Make sure that no DTCs are output. If any DTCs are output, proceed to Diagnostic Trouble Code Chart.
  • If the smart key system (for Start Function) has been canceled, enable the system before performing troubleshooting.

    Click here 2019 - 2022 MY RAV4 HV [11/2018 - 10/2022]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function, HV Model): CUSTOMIZE PARAMETERS

  • Inspect the fuses of circuits related to this system before performing the following procedure.
  • Before replacing the certification ECU (smart key ECU assembly) or an electrical key transmitter sub-assembly, refer to the Registration.

    Click here 2019 MY RAV4 HV [11/2018 - 10/2019]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function, HV Model): REGISTRATION 2020 - 2021 MY RAV4 HV [10/2019 - 12/2021]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function, HV Model): REGISTRATION

  • After completing repairs, confirm that the problem does not recur.
  • After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".
  • An antenna coil is connected between the terminals of the indoor electrical key antenna.
  • The door control receiver is also involved in interior certification.

HINT:

  • If interior certification does not succeed, the History of Reason for Operation may remain in the certification ECU (smart key ECU assembly).
  • If the operation history remains, refer to the history table to determine the conditions and narrow down any trouble areas.

Body Electrical > Smart Key > Utility

Tester Display

Operation History

PROCEDURE

1.

CHECK PUSH-BUTTON START FUNCTION

(a) Get into the vehicle while carrying the electrical key transmitter sub-assembly that has already been registered.

(b) Change the shift state to park (P).

(c) Check that the power source mode changes when the power switch is pressed without depressing the brake pedal.

Click here 2019 MY RAV4 HV [11/2018 - 02/2019]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function, HV Model): OPERATION CHECK 2019 - 2021 MY RAV4 HV [02/2019 - 12/2021]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function, HV Model): OPERATION CHECK

Result

Proceed to

Power source mode does not change when the electrical key transmitter sub-assembly is inside the push-button start function operation range only for the front side

A

Power source mode does not change when the electrical key transmitter sub-assembly is inside the push-button start function operation range only for the rear side

B

Power source mode does not change when the electrical key transmitter sub-assembly is inside the push-button start function operation range only for the luggage compartment

C

Power source mode does not change when the electrical key transmitter sub-assembly is inside any push-button start function operation range

D

B

GO TO STEP 6

C

GO TO STEP 10

D

GO TO STEP 14

A

2.

CHECK WAVE ENVIRONMENT

(a) Install the transmitter battery to the electrical key transmitter sub-assembly.

Click here 2019 - 2024 MY RAV4 RAV4 HV [11/2018 -        ]; MAINTENANCE: TRANSMITTER BATTERY(w/ Smart Key System): REMOVAL

(b) Bring the electrical key transmitter sub-assembly near the No. 1 indoor electrical key antenna assembly (front floor) and perform an smart key system check.

NOTICE:

Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the No. 1 indoor electrical key antenna assembly (front floor).

Click here 2019 MY RAV4 HV [11/2018 - 02/2019]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function, HV Model): PARTS LOCATION 2019 - 2021 MY RAV4 HV [02/2019 - 12/2021]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function, HV Model): PARTS LOCATION

HINT:

  • As the effect of wave interference decreases by moving the electrical key transmitter sub-assembly close to each indoor electrical key antenna assembly, it may be possible to check whether wave interference is the cause of the problem.
  • If the inspection result is that the problem only occurs in certain locations or at certain times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.
  • There may be wave interference if the vehicle is near broadcasting antennas, large video displays, wireless garage door opener systems, wireless security cameras, home security systems, etc. In this case, move the vehicle to a different location and check if there is any improvement.

OK:

The hybrid control system starts when the electrical key transmitter sub-assembly is held near each indoor electrical key antenna assembly and the power switch is pressed with the brake pedal depressed.

OK

AFFECTED BY WAVE INTERFERENCE

NG

3.

CHECK KEY DIAGNOSTIC MODE

(a) Connect the Techstream to the DLC3.

(b) Turn the power switch on (IG).

(c) Turn the Techstream on.

(d) Enter the following menus: Body Electrical / Smart Key / Utility / Communication Check(Key Diag Mode).

(e) Check the No. 1 indoor electrical key antenna assembly (front floor).

When the electrical key transmitter sub-assembly is at either inspection point, check that the buzzer sounds.

HINT:

  • Select either channel 1 or channel 2 and perform the key diagnostic mode inspection for each channel.
  • If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.
  • It is possible to check which No. 1 indoor electrical key antenna assembly (front floor) is operating by the sounding of the buzzer.
  • When the buzzer does not sound for No. 1 indoor electrical key antenna assembly (front floor), it can be judged that the certification ECU (smart key ECU assembly), which controls the No. 1 indoor electrical key antenna assembly (front floor), is malfunctioning.

*a

Inspection Point

Body Electrical > Smart Key > Utility

Tester Display

Communication Check(Key Diag Mode)

Result

Proceed to

The buzzer sounds

A

The buzzer does not sound

B

B

AFFECTED BY WAVE INTERFERENCE

A

4.

CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (FRONT FLOOR))

(a) Disconnect the G54 certification ECU (smart key ECU assembly) connector.

(b) Disconnect the G59 No. 1 indoor electrical key antenna assembly (front floor) connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

G54-8 (CLG5) - G59-1 (ANTE5)

Always

Below 1 Ω

G54-9 (CG5B) - G59-3 (CLGB)

Always

Below 1 Ω

G54-8 (CLG5) or G59-1 (ANTE5) - Other terminals and body ground

Always

10 kΩ or higher

G54-9 (CG5B) or G59-3 (CLGB) - Other terminals and body ground

Always

10 kΩ or higher

(d) Reconnect the G54 certification ECU (smart key ECU assembly) connector.

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

5.

CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (FRONT FLOOR))

(a) Using an oscilloscope, check the waveform.

*a

Front view of wire harness connector

(to No. 1 Indoor Electrical Key Antenna Assembly (Front Floor))

*b

Waveform

*c

For 30 seconds after closing any door

*d

After 30 seconds or more have elapsed since any door closed

OK:

Tester Connection

Condition

Tool Setting

Specified Condition

G59-1 (ANTE5) - G59-3 (CLGB)

Procedure:

  1. Power switch off
  2. Electrical key transmitter sub-assembly not inside vehicle
  3. Within 30 seconds of closing any door

2 V/DIV., 500 ms./DIV.

Pulse generation

(See waveform)

OK

REPLACE NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (FRONT FLOOR)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) 2019 MY RAV4 RAV4 HV [11/2018 - 02/2019]; THEFT DETERRENT / KEYLESS ENTRY: CERTIFICATION ECU: REMOVAL 2019 MY RAV4 RAV4 HV [02/2019 - 10/2019]; THEFT DETERRENT / KEYLESS ENTRY: CERTIFICATION ECU: REMOVAL 2020 MY RAV4 RAV4 HV [10/2019 - 08/2020]; THEFT DETERRENT / KEYLESS ENTRY: CERTIFICATION ECU: REMOVAL

6.

CHECK WAVE ENVIRONMENT

(a) Install the transmitter battery to the electrical key transmitter sub-assembly.

Click here 2019 - 2024 MY RAV4 RAV4 HV [11/2018 -        ]; MAINTENANCE: TRANSMITTER BATTERY(w/ Smart Key System): REMOVAL

(b) Bring the electrical key transmitter sub-assembly near the No. 1 indoor electrical key antenna assembly (rear floor) and perform an smart key system check.

HINT:

Check that the customize setting "Ignition Available Area" is set to "All".

Click here 2019 - 2022 MY RAV4 HV [11/2018 - 10/2022]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function, HV Model): CUSTOMIZE PARAMETERS

NOTICE:

Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the center of the No. 1 indoor electrical key antenna assembly (rear floor).

Click here 2019 MY RAV4 HV [11/2018 - 02/2019]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function, HV Model): PARTS LOCATION 2019 - 2021 MY RAV4 HV [02/2019 - 12/2021]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function, HV Model): PARTS LOCATION

HINT:

  • As the effect of wave interference decreases by moving the electrical key transmitter sub-assembly close to each indoor electrical key antenna assembly, it may be possible to check whether wave interference is the cause of the problem.
  • If the inspection result is that the problem only occurs in certain locations or at certain times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.
  • There may be wave interference if the vehicle is near broadcasting antennas, large video displays, wireless garage door opener systems, wireless security cameras, home security systems, etc. In this case, move the vehicle to a different location and check if there is any improvement.

OK:

The hybrid control system starts when the electrical key transmitter sub-assembly is held near each indoor electrical key antenna assembly and the power switch is pressed with the brake pedal depressed.

OK

AFFECTED BY WAVE INTERFERENCE

NG

7.

CHECK KEY DIAGNOSTIC MODE

(a) Connect the Techstream to the DLC3.

(b) Turn the power switch on (IG).

(c) Turn the Techstream on.

(d) Enter the following menus: Body Electrical / Smart Key / Utility / Communication Check(Key Diag Mode).

(e) Check the No. 1 indoor electrical key antenna assembly (rear floor).

When the electrical key transmitter sub-assembly is at either inspection point, check that the buzzer sounds.

HINT:

  • Select either channel 1 or channel 2 and perform the key diagnostic mode inspection for each channel.
  • If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.
  • It is possible to check which No. 1 indoor electrical key antenna assembly (rear floor) is operating by the sounding of the buzzer.
  • When the buzzer does not sound for No. 1 indoor electrical key antenna assembly (rear floor), it can be judged that the certification ECU (smart key ECU assembly), which controls the No. 1 indoor electrical key antenna assembly (rear floor), is malfunctioning.

*a

Inspection Point

Body Electrical > Smart Key > Utility

Tester Display

Communication Check(Key Diag Mode)

Result

Proceed to

The buzzer sounds

A

The buzzer does not sound

B

B

AFFECTED BY WAVE INTERFERENCE

A

8.

CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (REAR FLOOR))

(a) Disconnect the M7 certification ECU (smart key ECU assembly) connector.

(b) Disconnect the M9 No. 1 indoor electrical key antenna assembly (rear floor) connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

M7-5 (CLG6) - M9-1 (ANTE6)

Always

Below 1 Ω

M7-6 (CG6B) - M9-3 (CLGB)

Always

Below 1 Ω

M7-5 (CLG6) or M9-1 (ANTE6) - Other terminals and body ground

Always

10 kΩ or higher

M7-6 (CG6B) or M9-3 (CLGB) - Other terminals and body ground

Always

10 kΩ or higher

(d) Reconnect the M7 certification ECU (smart key ECU assembly) connector.

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

9.

CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (REAR FLOOR))

(a) Using an oscilloscope, check the waveform.

*a

Front view of wire harness connector

(to No. 1 Indoor Electrical Key Antenna Assembly (Rear Floor))

*b

Waveform

*c

For 30 seconds after closing any door

*d

After 30 seconds or more have elapsed since any door closed

OK:

Tester Connection

Condition

Tool Setting

Specified Condition

M9-1 (ANTE6) - M9-3 (CLGB)

Procedure:

  1. Power switch off
  2. Electrical key transmitter sub-assembly not inside vehicle
  3. Within 30 seconds of closing any door

2 V/DIV., 500 ms./DIV.

Pulse generation

(See waveform)

OK

REPLACE NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (REAR FLOOR)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) 2019 MY RAV4 RAV4 HV [11/2018 - 02/2019]; THEFT DETERRENT / KEYLESS ENTRY: CERTIFICATION ECU: REMOVAL 2019 MY RAV4 RAV4 HV [02/2019 - 10/2019]; THEFT DETERRENT / KEYLESS ENTRY: CERTIFICATION ECU: REMOVAL 2020 MY RAV4 RAV4 HV [10/2019 - 08/2020]; THEFT DETERRENT / KEYLESS ENTRY: CERTIFICATION ECU: REMOVAL

10.

CHECK WAVE ENVIRONMENT

(a) Install the transmitter battery to the electrical key transmitter sub-assembly.

Click here 2019 - 2024 MY RAV4 RAV4 HV [11/2018 -        ]; MAINTENANCE: TRANSMITTER BATTERY(w/ Smart Key System): REMOVAL

(b) Bring the electrical key transmitter sub-assembly near the No. 1 indoor electrical key antenna assembly (inside luggage compartment) and perform an smart key system check.

HINT:

Check that the customize setting "Ignition Available Area" is set to "All".

Click here 2019 - 2022 MY RAV4 HV [11/2018 - 10/2022]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function, HV Model): CUSTOMIZE PARAMETERS

NOTICE:

Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the center of the No. 1 indoor electrical key antenna assembly (inside luggage compartment).

Click here 2019 MY RAV4 HV [11/2018 - 02/2019]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function, HV Model): PARTS LOCATION 2019 - 2021 MY RAV4 HV [02/2019 - 12/2021]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function, HV Model): PARTS LOCATION

HINT:

  • As the effect of wave interference decreases by moving the electrical key transmitter sub-assembly close to each indoor electrical key antenna assembly, it may be possible to check whether wave interference is the cause of the problem.
  • If the inspection result is that the problem only occurs in certain locations or at certain times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.
  • There may be wave interference if the vehicle is near broadcasting antennas, large video displays, wireless garage door opener systems, wireless security cameras, home security systems, etc. In this case, move the vehicle to a different location and check if there is any improvement.

OK:

The hybrid control system starts when the electrical key transmitter sub-assembly is held near each indoor electrical key antenna assembly and the power switch is pressed with the brake pedal depressed.

OK

AFFECTED BY WAVE INTERFERENCE

NG

11.

CHECK KEY DIAGNOSTIC MODE

(a) Connect the Techstream to the DLC3.

(b) Turn the power switch on (IG).

(c) Turn the Techstream on.

(d) Enter the following menus: Body Electrical / Smart Key / Utility / Communication Check(Key Diag Mode).

(e) Check the No. 1 indoor electrical key antenna assembly (inside luggage compartment).

When the electrical key transmitter sub-assembly is at either inspection point, check that the buzzer sounds.

HINT:

  • Select either channel 1 or channel 2 and perform the key diagnostic mode inspection for each channel.
  • If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.
  • It is possible to check which No. 1 indoor electrical key antenna assembly (inside luggage compartment) is operating by the sounding of the buzzer.
  • When the buzzer does not sound for No. 1 indoor electrical key antenna assemby (rear floor), it can be judged that the certification ECU (smart key ECU assembly), which controls the No. 1 indoor electrical key antenna assembly (inside luggage compartment), is malfunctioning.

*a

Inspection Point

Body Electrical > Smart Key > Utility

Tester Display

Communication Check(Key Diag Mode)

Result

Proceed to

The buzzer sounds

A

The buzzer does not sound

B

B

AFFECTED BY WAVE INTERFERENCE

A

12.

CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (INSIDE LUGGAGE COMPARTMENT))

(a) Disconnect the M7 certification ECU (smart key ECU assembly) connector.

(b) Disconnect the M10 No. 1 indoor electrical key antenna assembly (inside luggage compartment) connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

M7-11 (CLG7) - M10-1 (ANTE7)

Always

Below 1 Ω

M7-10 (CG7B) - M10-3 (CLGB)

Always

Below 1 Ω

M7-11 (CLG7) or M10-1 (ANTE7) - Other terminals and body ground

Always

10 kΩ or higher

M7-10 (CG7B) or M10-3 (CLGB) - Other terminals and body ground

Always

10 kΩ or higher

(d) Reconnect the M7 certification ECU (smart key ECU assembly) connector.

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

13.

CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (INSIDE LUGGAGE COMPARTMENT))

(a) Using an oscilloscope, check the waveform.

*a

Front view of wire harness connector

(to No. 1 Indoor Electrical Key Antenna Assembly (Inside Luggage Compartment))

*b

Waveform

*c

For 30 seconds after closing any door

*d

After 30 seconds or more have elapsed since any door closed

OK:

Tester Connection

Condition

Tool Setting

Specified Condition

M10-1 (ANTE7) - M10-3 (CLGB)

Procedure:

  1. Power switch off
  2. Electrical key transmitter sub-assembly not inside vehicle
  3. Within 30 seconds of closing any door

2 V/DIV., 500 ms./DIV.

Pulse generation

(See waveform)

OK

REPLACE NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (INSIDE LUGGAGE COMPARTMENT)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) 2019 MY RAV4 RAV4 HV [11/2018 - 02/2019]; THEFT DETERRENT / KEYLESS ENTRY: CERTIFICATION ECU: REMOVAL 2019 MY RAV4 RAV4 HV [02/2019 - 10/2019]; THEFT DETERRENT / KEYLESS ENTRY: CERTIFICATION ECU: REMOVAL 2020 MY RAV4 RAV4 HV [10/2019 - 08/2020]; THEFT DETERRENT / KEYLESS ENTRY: CERTIFICATION ECU: REMOVAL

14.

CHECK TRANSMITTER BATTERY

(a) Check the transmitter battery level of the electrical key transmitter sub-assembly that was checked first.

(1) Press and hold the lock switch of the electrical key transmitter sub-assembly for 5 seconds and check the number of times that the LED illuminates.

HINT:

  • The electrical key transmitter sub-assembly sends voltage information to the certification ECU (smart key ECU assembly) when it is being used. "Yes" is displayed for the Data List item "Key Low Battery" when this voltage information indicates 2.2 V or less.

    Click here 2019 - 2021 MY RAV4 HV [11/2018 - 12/2021]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function, HV Model): DATA LIST / ACTIVE TEST

  • Even if the transmitter battery is depleted, it is still possible to start the hybrid control system by holding the electrical key transmitter sub-assembly near the power switch, depressing the brake pedal and pressing the power switch.

Result

Proceed to

LED illuminates 3 times or more when switch is pressed and held

A

LED does not illuminate when switch is pressed and held

B

LED illuminates once or twice but not a third time

C

B

GO TO STEP 21

C

REPLACE TRANSMITTER BATTERY

A

15.

CHECK ENTRY LOCK / UNLOCK FUNCTION

(a) Check that the entry lock and unlock functions operate on each door.

Click here 2019 MY RAV4 HV [11/2018 - 02/2019]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Entry Function, HV Model): OPERATION CHECK 2019 - 2023 MY RAV4 HV [02/2019 - 10/2023]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Entry Function, HV Model): OPERATION CHECK

HINT:

If the door control receiver is defective, code verification does not begin in the cabin and the entry lock and unlock functions do not operate.

Result

Proceed to

Entry lock/unlock functions operate normally

A

An entry lock/unlock functions does not operate normally

B

B

GO TO SMART KEY SYSTEM (for Entry Function) (All door entry lock/unlock functions and wireless functions do not operate) 2019 MY RAV4 HV [11/2018 - 02/2019]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Entry Function, HV Model): All Door Entry Lock/Unlock Functions and Wireless Functions do not Operate 2019 - 2022 MY RAV4 HV [02/2019 - 10/2022]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Entry Function, HV Model): All Door Entry Lock/Unlock Functions and Wireless Functions do not Operate

A

16.

READ VALUE USING TECHSTREAM (START SWITCH1, START SWITCH2)

(a) Connect the Techstream to the DLC3.

(b) Turn the power switch on (IG).

(c) Turn the Techstream on.

(d) Enter the following menus: Body Electrical / Power Source Control / Data List.

(e) Read the Data List according to the display on the Techstream.

Body Electrical > Power Source Control > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Start Switch1

Power switch 1 status

OFF or ON

OFF: Power switch not pressed

ON: Power switch pressed

  • If the power switch is pressed for a short time, the display may not change.
  • Use this item to determine if the power switch input signal is malfunctioning.

Start Switch2

Power switch 2 status

OFF or ON

OFF: Power switch not pressed

ON: Power switch pressed

  • Backup for power switch 1. However, when the power switch is pressed and held, the power source mode can only be changed when both power switch 1 and 2 are normal.
  • Behaves the same way as power switch 1.

Body Electrical > Power Source Control > Data List

Tester Display

Start Switch1

Start Switch2

OK:

The Techstream display changes correctly in response to the power switch operation.

NG

GO TO STEP 19

OK

17.

CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

(a) Measure the voltage while confirming the power source mode on the Data List.

*a

Component with harness connected

(Certification ECU (Smart Key ECU Assembly))

-

-

Body Electrical > Power Source Control > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Power Supply Condition

Power supply state

All OFF, ACC ON, IG ON or ST ON

All OFF: Power switch off

ACC ON: Power switch on (ACC)

IG ON: Power switch on (IG)

ST ON: Sending hybrid control system start request signal

-

Body Electrical > Power Source Control > Data List

Tester Display

Power Supply Condition

Standard Voltage:

Tester Connection

Switch Condition

Specified Condition

G54-17 (IG1D) - Body ground

Power switch off

1 V or less

Power switch on (ACC)

Power switch on (IG)

9 V or higher

G54-16 (ACCD) - Body ground

Power switch off

1 V or less

Power switch on (ACC)

8.5 V or higher

Power switch on (IG)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) 2019 MY RAV4 RAV4 HV [11/2018 - 02/2019]; THEFT DETERRENT / KEYLESS ENTRY: CERTIFICATION ECU: REMOVAL 2019 MY RAV4 RAV4 HV [02/2019 - 10/2019]; THEFT DETERRENT / KEYLESS ENTRY: CERTIFICATION ECU: REMOVAL 2020 MY RAV4 RAV4 HV [10/2019 - 08/2020]; THEFT DETERRENT / KEYLESS ENTRY: CERTIFICATION ECU: REMOVAL

OK

18.

CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - BODY GROUND)

(a) Disconnect the instrument panel junction block assembly connector.

*a

Front view of wire harness connector

(to Instrument Panel Junction Block Assembly)

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

4D-3 - Body ground

Always

Below 1 Ω

OK

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY 2019 MY RAV4 RAV4 HV [11/2018 - 02/2019]; POWER DISTRIBUTION: MAIN BODY ECU: REMOVAL 2019 MY RAV4 RAV4 HV [02/2019 - 10/2019]; POWER DISTRIBUTION: MAIN BODY ECU: REMOVAL 2020 MY RAV4 RAV4 HV [10/2019 - 08/2020]; POWER DISTRIBUTION: MAIN BODY ECU: REMOVAL

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

19.

INSPECT POWER SWITCH

(a) Remove the power switch.

Click here 2019 - 2024 MY RAV4 HV [11/2018 -        ]; A25A-FXS (STARTING): POWER SWITCH: REMOVAL

(b) Inspect the power switch.

Click here 2019 - 2024 MY RAV4 HV [11/2018 -        ]; A25A-FXS (STARTING): POWER SWITCH: INSPECTION

NG

REPLACE POWER SWITCH

OK

20.

CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - POWER SWITCH)

(a) Disconnect the G54 certification ECU (smart key ECU assembly) connector.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

G54-23 (SSW1) - G55-5 (SS1)

Always

Below 1 Ω

G54-21 (SSW2) - G55-1 (SS2)

Always

Below 1 Ω

G54-11 (AGND) - G55-6 (AGND)

Always

Below 1 Ω

G54-23 (SSW1) or G55-5 (SS1) - Other terminals and body ground

Always

10 kΩ or higher

G54-21 (SSW2) or G55-1 (SS2) - Other terminals and body ground

Always

10 kΩ or higher

G54-11 (AGND) or G55-6 (AGND) - Other terminals and body ground

Always

10 kΩ or higher

OK

REPLACE NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (INSIDE LUGGAGE COMPARTMENT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

21.

INSPECT TRANSMITTER BATTERY

(a) Inspect the transmitter battery.

Click here 2019 - 2024 MY RAV4 RAV4 HV [11/2018 -        ]; DOOR LOCK: DOOR CONTROL TRANSMITTER (w/ Smart Key System): INSPECTION

NOTICE:

Do not wrap the lead wire around a terminal, wedge it between terminals, or solder it. The terminal may be deformed or damaged, and the transmitter battery will not be able to be installed correctly.

OK

REPLACE ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY

NG

REPLACE TRANSMITTER BATTERY