| Last Modified: 01-30-2024 | 6.11:8.1.0 | Doc ID: RM100000001G200 |
| Model Year Start: 2019 | Model: RAV4 | Prod Date Range: [11/2018 - ] |
| Title: THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Entry Function, Gasoline Model): Back Door Entry Unlock Function does not Operate; 2019 - 2024 MY RAV4 [11/2018 - ] | ||
|
Back Door Entry Unlock Function does not Operate |
DESCRIPTION
If the entry unlock function does not operate for the back door only, but the entry lock function operates, the request code is being transmitted properly from the back door. In this case, there may be a problem related to the unlock switch (connection between the back door opener switch assembly and certification ECU (smart key ECU assembly)).
WIRING DIAGRAM
CAUTION / NOTICE / HINT
NOTICE:
- When using the Techstream with the engine switch off, connect the Techstream to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the Techstream and the vehicle begins. Then select the vehicle type under manual mode and enter the following menus: Body Electrical / Smart Key. While using the Techstream, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the Techstream and the vehicle.
-
The smart key system (for Entry Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the smart key system (for Entry Function) after confirming that the communication systems are functioning properly.
Click here
![2019 - 2020 MY RAV4 [11/2018 - 08/2020]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function, Gasoline Model): HOW TO PROCEED WITH TROUBLESHOOTING](/t3Portal/stylegraphics/info.gif)
-
Before replacing the certification ECU (smart key ECU assembly), refer to Registration.
Click here
- After repair, confirm that no DTCs are output.
- Check that there are no electrical key transmitter sub-assemblies in the vehicle.
PROCEDURE
|
1. |
CHECK POWER DOOR LOCK CONTROL SYSTEM |
(a) When the door control switch on the multiplex network master switch assembly is operated, check that the doors unlock and lock according to the switch operation.
Click here
OK:
Door locks operate normally.
| NG |
|
|
|
2. |
CHECK CUSTOMIZE SETTING (Back Door Opening Operation) |
(a) Connect the Techstream to the DLC3.
(b) Turn the engine switch on (IG).
(c) Turn the Techstream on.
(d) Enter the following menus: Customize Setting / Smart Key / Access.
Smart Key / Access
|
Tester Display |
Description |
Default |
Setting |
ECU |
|---|---|---|---|---|
|
Back Door Opening Operation |
Function that sets the back door when the user is carrying the electrical key transmitter sub-assembly and presses the back door opener switch assembly (unlock switch). |
Long |
00:Long,01:Twice,10:OFF |
Certification ECU (Smart key ECU assembly) |
|
Result |
Proceed to |
|---|---|
|
Customize setting is "Long" or "Twice" |
A |
|
Customize setting is "OFF" |
B |
| B |
|
PERFORM CUSTOMIZE SETTING (Proceed to Customize Parameters)
|
|
|
3. |
READ VALUE USING TECHSTREAM (TR/B-DOOR UNLOCK SW) |
(a) Enter the following menus: Body Electrical / Smart Key / Data List.
(b) Read the Data List according to the display on the Techstream.
Body Electrical > Smart Key > Data List
|
Tester Display |
Measurement Item |
Range |
Normal Condition |
Diagnostic Note |
|---|---|---|---|---|
|
Tr/B-Door Unlock SW |
Back door opener switch assembly (unlock switch) |
ON or OFF |
ON: Back door opener switch assembly (unlock switch) pressed OFF: Back door opener switch assembly (unlock switch) not pressed |
|
Body Electrical > Smart Key > Data List
|
Tester Display |
|---|
|
Tr/B-Door Unlock SW |
OK:
The Techstream display changes correctly in response to the operation of the back door opener switch assembly.
| OK |
|
REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
|
|
|
4. |
CHECK HARNESS AND CONNECTOR (BACK DOOR OPENER SWITCH ASSEMBLY - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)) |
(a) Disconnect the R10 back door opener switch assembly connector.
(b) Disconnect the M7 certification ECU (smart key ECU assembly) connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
R10-3 (UL) - M7-26 (TSW5) |
Always |
Below 1 Ω |
|
R10-3 (UL) or M7-26 (TSW5) - Other terminals and body ground |
Always |
10 kΩ or higher |
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
5. |
INSPECT BACK DOOR OPENER SWITCH ASSEMBLY (UNLOCK SWITCH) |
(a) Remove the back door opener switch assembly.
Click here
(b) Inspect the back door opener switch assembly.
Click here
| OK |
|
REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
|
| NG |
|
|
|