| Last Modified: 01-30-2024 | 6.11:8.1.0 | Doc ID: RM100000001FREH |
| Model Year Start: 2019 | Model: RAV4 | Prod Date Range: [11/2018 - 10/2022] |
| Title: PARK ASSIST / MONITORING: PANORAMIC VIEW MONITOR SYSTEM (for Gasoline Model): C1686; Driver Side Camera Video Sync Signal Malfunction; 2019 - 2022 MY RAV4 [11/2018 - 10/2022] | ||
|
DTC |
C1686 |
Driver Side Camera Video Sync Signal Malfunction |
DESCRIPTION
This DTC is stored if the parking assist ECU judges as a result of its self check that a synchronization problem is occurring in the image signal sent from the driver side television camera assembly to the parking assist ECU.
|
DTC No. |
Detection Item |
DTC Detection Condition |
Trouble Area |
|---|---|---|---|
|
C1686 |
Driver Side Camera Video Sync Signal Malfunction |
Side camera feedback malfunction |
|
WIRING DIAGRAM
CAUTION / NOTICE / HINT
NOTICE:
-
When "!" mark is displayed on the multi-display assembly after the cable is disconnected from the negative (-) battery terminal, correct the steering angle neutral point.
Click here
![2019 - 2022 MY RAV4 [11/2018 - 10/2022]; PARK ASSIST / MONITORING: PANORAMIC VIEW MONITOR SYSTEM (for Gasoline Model): INITIALIZATION](/t3Portal/stylegraphics/info.gif)
-
Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the panoramic view monitor system may be needed.
Click here
PROCEDURE
|
1. |
CHECK FOR DTC |
(a) Clear the DTCs.
Click here
Chassis > Circumference Monitoring Camera Control Module > Clear DTCs
(b) Check for DTCs.
Click here
Chassis > Circumference Monitoring Camera Control Module > Trouble Codes
OK:
DTC C1686 is not output.
| OK |
|
|
|
2. |
CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - OUTER REAR VIEW MIRROR ASSEMBLY LH) |
(a) Disconnect the N24 parking assist ECU connector.
(b) Disconnect the J13 outer rear view mirror assembly LH connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
N24-12 (LCB+) - J13-3 (LCB+) |
Always |
Below 1 Ω |
|
N24-10 (LCV+) - J13-4 (LCV+) |
Always |
Below 1 Ω |
|
N24-34 (LCV-) - J13-12 (LCV-) |
Always |
Below 1 Ω |
|
N24-35 (LGND) - J13-11 (LGND) |
Always |
Below 1 Ω |
|
N24-12 (LCB+) or J13-3 (LCB+) - Body ground |
Always |
10 kΩ or higher |
|
N24-10 (LCV+) or J13-4 (LCV+) - Body ground |
Always |
10 kΩ or higher |
|
N24-34 (LCV-) or J13-12 (LCV-) - Body ground |
Always |
10 kΩ or higher |
|
N24-35 (LGND) or J13-11 (LGND) - Body ground |
Always |
10 kΩ or higher |
|
N24-11 (SGND) - Body ground |
Always |
10 kΩ or higher |
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
3. |
CHECK PARKING ASSIST ECU (LCV-, LGND) |
|
(a) Disconnect the N24 parking assist ECU connector. |
|
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
35 (LGND) - Body ground |
Always |
Below 1 Ω |
|
34 (LCV-) - Body ground |
Always |
Below 1 Ω |
| NG |
|
|
|
4. |
CHECK PARKING ASSIST ECU (LCB+, LGND) |
|
(a) Measure the resistance according to the value(s) in the table below. Standard Resistance:
|
|
(b) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
|
Tester Connection |
Switch Condition |
Specified Condition |
|---|---|---|
|
N24-12 (LCB+) - N24-35 (LGND) |
Engine switch on (IG) |
5.5 to 7.05 V |
|
N24-12 (LCB+) - N24-35 (LGND) |
Engine switch off |
Below 1 V |
| NG |
|
|
|
5. |
CHECK SIDE TELEVISION CAMERA ASSEMBLY LH (LCV+, LGND) |
(a) Using an oscilloscope, check the waveform of the side television camera assembly LH.
HINT:
A waterproof connector is used for the side television camera assembly LH. Therefore, inspect the waveform at the parking assist ECU with the connector connected.
|
*a |
Component with harness connected (Parking Assist ECU) |
*b |
Waveform 1 (camera lens not covered, displaying an image) |
|
*c |
Waveform 2 (camera lens covered, blacking out the screen) |
*d |
Synchronization Signal |
|
*e |
Video Waveform |
- |
- |
HINT:
- The video waveform changes according to the image sent by the side television camera assembly LH.
- The video waveform is constantly output when the engine switch is on (ACC).
Measurement Condition
|
Item |
Content |
|---|---|
|
Tester Connection |
N24-10 (LCV+) - N24-35 (LGND) |
|
Tool Setting |
200 mV/DIV., 50 μsec./DIV. |
|
Condition |
Engine switch on (IG), panoramic view monitor switch on |
OK:
Waveform is similar to that shown in illustration.
| OK |
|
|
|
6. |
INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH |
|
(a) Disconnect the outer rear view mirror assembly LH connector. |
|
(b) Disconnect the side television camera assembly LH connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
A-1 (SCB+) - J13-3 (LCB+) |
Always |
Below 1 Ω |
|
A-3 (SCV+) - J13-4 (LCV+) |
Always |
Below 1 Ω |
|
A-7 (SCV-) - J13-12 (LCV-) |
Always |
Below 1 Ω |
|
A-5 (SGND) - J13-11 (LGND) |
Always |
Below 1 Ω |
|
A-1 (SCB+) or J13-3 (LCB+) - Body ground |
Always |
10 kΩ or higher |
|
A-3 (SCV+) or J13-4 (LCV+) - Body ground |
Always |
10 kΩ or higher |
|
A-7 (SCV-) or J13-12 (LCV-) - Body ground |
Always |
10 kΩ or higher |
|
A-5 (SGND) or J13-11 (LGND) - Body ground |
Always |
10 kΩ or higher |
| NG |
|
|
|
7. |
CHECK SIDE TELEVISION CAMERA ASSEMBLY LH |
(a) Replace the side television camera assembly LH with a new or normally functioning one.
Click here
|
|
8. |
CHECK FOR DTC |
(a) Clear the DTCs.
Click here
Chassis > Circumference Monitoring Camera Control Module > Clear DTCs
(b) Check for DTCs.
Click here
Chassis > Circumference Monitoring Camera Control Module > Trouble Codes
OK:
DTC C1686 is not output.
| OK |
|
END (SIDE TELEVISION CAMERA ASSEMBLY LH IS DEFECTIVE) |
| NG |
|
|
|