| Last Modified: 01-30-2024 | 6.11:8.1.0 | Doc ID: RM100000001FREG |
| Model Year Start: 2019 | Model: RAV4 | Prod Date Range: [11/2018 - 10/2022] |
| Title: PARK ASSIST / MONITORING: PANORAMIC VIEW MONITOR SYSTEM (for Gasoline Model): C1684; Side Camera Current Malfunction; 2019 - 2022 MY RAV4 [11/2018 - 10/2022] | ||
|
DTC |
C1684 |
Side Camera Current Malfunction |
DESCRIPTION
This DTC is stored if the parking assist ECU judges as a result of its self check that a synchronization problem is occurring in the image signal sent from the passenger side television camera assembly to the parking assist ECU.
|
DTC No. |
Detection Item |
DTC Detection Condition |
Trouble Area |
|---|---|---|---|
|
C1684 |
Side Camera Current Malfunction |
Side camera current malfunction |
|
WIRING DIAGRAM
CAUTION / NOTICE / HINT
NOTICE:
-
When "!" mark is displayed on the radio and display receiver assembly after the cable is disconnected from the negative (-) battery terminal, correct the steering angle neutral point.
Click here
![2019 - 2022 MY RAV4 [11/2018 - 10/2022]; PARK ASSIST / MONITORING: PANORAMIC VIEW MONITOR SYSTEM (for Gasoline Model): INITIALIZATION](/t3Portal/stylegraphics/info.gif)
-
Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the panoramic view monitor system may be needed.
Click here
PROCEDURE
|
1. |
CHECK FOR DTC |
(a) Clear the DTCs.
Click here
Chassis > Circumference Monitoring Camera Control Module > Clear DTCs
(b) Check for DTCs.
Click here
Chassis > Circumference Monitoring Camera Control Module > Trouble Codes
OK:
DTC C1684 is not output.
| OK |
|
|
|
2. |
CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - OUTER REAR VIEW MIRROR ASSEMBLY RH) |
(a) Disconnect the N24 parking assist ECU connector.
(b) Disconnect the I13 outer rear view mirror assembly RH connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
N24-40 (RCB+) - I13-3 (RCB+) |
Always |
Below 1 Ω |
|
N24-17 (RGND) - I13-11 (RGND) |
Always |
Below 1 Ω |
|
N24-40 (RCB+) or I13-3 (RCB+) - Body ground |
Always |
10 kΩ or higher |
|
N24-17 (RGND) or I13-11 (RGND) - Body ground |
Always |
10 kΩ or higher |
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
3. |
CHECK PARKING ASSIST ECU |
|
(a) Measure the resistance according to the value(s) in the table below. Standard Resistance:
|
|
(b) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
|
Tester Connection |
Switch Condition |
Specified Condition |
|---|---|---|
|
N24-40 (RCB+) - N24-17 (RGND) |
Engine switch on (IG) |
5.5 to 7.05 V |
|
N24-40 (RCB+) - N24-17 (RGND) |
Engine switch off |
Below 1 V |
| NG |
|
|
|
4. |
INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH |
|
(a) Disconnect the side television camera assembly RH connector. |
|
(b) Disconnect the outer rear view mirror assembly RH connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
B-1 (SCB+) - I13-3 (RCB+) |
Always |
Below 1 Ω |
|
B-5 (SGND) - I13-11 (RGND) |
Always |
Below 1 Ω |
|
B-1 (SCB+) or I13-3 (RCB+) - Body ground |
Always |
10 kΩ or higher |
|
B-5 (SGND) or I13-11 (RGND) - Body ground |
Always |
10 kΩ or higher |
| NG |
|
|
|
5. |
REPLACE SIDE TELEVISION CAMERA ASSEMBLY RH |
(a) Replace the side television camera assembly RH with a new or normally functioning one.
Click here
|
|
6. |
CHECK FOR DTC |
(a) Clear the DTCs.
Click here
Chassis > Circumference Monitoring Camera Control Module > Clear DTCs
(b) Check for DTCs.
Click here
Chassis > Circumference Monitoring Camera Control Module > Trouble Codes
OK:
DTC C1684 is not output.
| OK |
|
END (SIDE TELEVISION CAMERA ASSEMBLY RH IS DEFECTIVE) |
| NG |
|
|
|