Last Modified: 01-30-2024 6.11:8.1.0 Doc ID: RM100000001FQRN
Model Year Start: 2019 Model: RAV4 Prod Date Range: [11/2018 - 08/2020]
Title: SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM (w/o Occupant Classification System): B1647,B1648; Side Satellite Sensor Bus Lost Communication (LH); 2019 - 2020 MY RAV4 RAV4 HV [11/2018 - 08/2020]

DTC

B1647

Side Satellite Sensor Bus Lost Communication (LH)

DTC

B1648

Side Satellite Sensor Bus Initialization Error (LH)

DESCRIPTION

The side collision sensor LH circuit consists of the airbag ECU assembly, side airbag pressure sensor LH and No. 2 side airbag sensor assembly LH.

The No. 2 side airbag sensor assembly LH and side airbag pressure sensor LH detect impacts to the vehicle and send signals to the airbag ECU assembly to determine if the SRS should be deployed.

These DTCs are stored when a malfunction is detected in the circuit for the side collision sensor LH circuit.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

Warning Indicate

Test Mode / Check Mode

B1647

Side Satellite Sensor Bus Lost Communication (LH)

One of the following conditions is met:

  • The airbag ECU assembly detects a line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to B+ signal in the circuit for the side satellite sensor bus LH for 2 seconds.
  • A side airbag pressure sensor LH malfunction.
  • A No. 2 side airbag sensor assembly LH malfunction.
  • An airbag ECU assembly malfunction.
  • Floor wire
  • Front door wire LH
  • Side airbag pressure sensor LH
  • No. 2 side airbag sensor assembly LH
  • Airbag ECU assembly

Comes on

Not applicable

B1648

Side Satellite Sensor Bus Initialization Error (LH)

One of the following conditions is met:

  • The airbag ECU assembly detects a line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to B+ signal in the circuit for the side satellite sensor bus LH for 2 seconds.
  • A side airbag pressure sensor LH malfunction.
  • A No. 2 side airbag sensor assembly LH malfunction.
  • An airbag ECU assembly malfunction.
  • Floor wire
  • Front door wire LH
  • Side airbag pressure sensor LH
  • No. 2 side airbag sensor assembly LH
  • Airbag ECU assembly

Comes on

Not applicable

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

  • After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

    Click here 2019 MY RAV4 RAV4 HV [11/2018 - 02/2019]; INTRODUCTION: REPAIR INSTRUCTION: INITIALIZATION 2019 MY RAV4 RAV4 HV [02/2019 - 10/2019]; INTRODUCTION: REPAIR INSTRUCTION: INITIALIZATION 2020 MY RAV4 RAV4 HV [10/2019 - 06/2020]; INTRODUCTION: REPAIR INSTRUCTION: INITIALIZATION 2020 MY RAV4 RAV4 HV [06/2020 - 08/2020]; INTRODUCTION: REPAIR INSTRUCTION: INITIALIZATION

  • When disconnecting the cable from the negative (-) auxiliary battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.

    Click here 2019 MY RAV4 RAV4 HV [11/2018 - 02/2019]; INTRODUCTION: REPAIR INSTRUCTION: INITIALIZATION 2019 MY RAV4 RAV4 HV [02/2019 - 10/2019]; INTRODUCTION: REPAIR INSTRUCTION: INITIALIZATION 2020 MY RAV4 RAV4 HV [10/2019 - 06/2020]; INTRODUCTION: REPAIR INSTRUCTION: INITIALIZATION 2020 MY RAV4 RAV4 HV [06/2020 - 08/2020]; INTRODUCTION: REPAIR INSTRUCTION: INITIALIZATION

  • After replacing the airbag ECU assembly, refer to initialization.

    Click here 2019 MY RAV4 RAV4 HV [11/2018 - 02/2019]; INTRODUCTION: REPAIR INSTRUCTION: INITIALIZATION 2019 MY RAV4 RAV4 HV [02/2019 - 10/2019]; INTRODUCTION: REPAIR INSTRUCTION: INITIALIZATION 2020 MY RAV4 RAV4 HV [10/2019 - 06/2020]; INTRODUCTION: REPAIR INSTRUCTION: INITIALIZATION 2020 MY RAV4 RAV4 HV [06/2020 - 08/2020]; INTRODUCTION: REPAIR INSTRUCTION: INITIALIZATION

PROCEDURE

1.

CHECK CONNECTION OF CONNECTORS

(a) Turn the ignition switch off.

(b) Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 90 seconds.

(c) Check that the connectors are properly connected to the airbag ECU assembly and No. 2 side airbag sensor assembly LH.

The connectors are not properly connected

CONNECT CONNECTORS PROPERLY

The connectors are properly connected

2.

CHECK CONNECTORS

(a) Disconnect the connectors from the airbag ECU assembly and No. 2 side airbag sensor assembly LH.

*1

No. 2 Side Airbag Sensor Assembly LH

*2

Airbag ECU Assembly

*3

Floor Wire

(b) Check that the connectors (on the airbag ECU assembly side and No. 2 side airbag sensor assembly LH side) are not damaged.

The connectors are deformed or damaged

REPLACE FLOOR WIRE

The connectors are not deformed or damaged

3.

CHECK FLOOR WIRE

(a) Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.

*1

No. 2 Side Airbag Sensor Assembly LH

*2

Airbag ECU Assembly

*3

Floor Wire

*4

Service Wire

*a

Front view of wire harness connector

(to No. 2 Side Airbag Sensor Assembly LH)

*b

Front view of wire harness connector

(to Airbag ECU Assembly)

(b) Turn the ignition switch to ON.

(c) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Switch Condition

Specified Condition

N22-4 (BCL+) - Body ground

Ignition switch ON

Below 1 V

N22-3 (BCL-) - Body ground

Ignition switch ON

Below 1 V

(d) Turn the ignition switch off.

(e) Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 90 seconds.

(f) Using a service wire, connect terminals 32 (BBL+) and 31 (BBL-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.

(g) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

N22-4 (BCL+) - N22-3 (BCL-)

Always

Below 1 Ω

(h) Disconnect the service wire from connector B.

(i) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

N22-4 (BCL+) - N22-3 (BCL-)

Always

1 MΩ or higher

N22-4 (BCL+) - Body ground

Always

1 MΩ or higher

N22-3 (BCL-) - Body ground

Always

1 MΩ or higher

NG

REPLACE FLOOR WIRE

OK

4.

CHECK NO. 2 SIDE AIRBAG SENSOR ASSEMBLY LH

(a) Connect the connector to the airbag ECU assembly.

*1

No. 2 Side Airbag Sensor Assembly RH

*2

Airbag ECU Assembly

(b) Interchange the No. 2 side airbag sensor assembly LH with RH and connect the connectors to them.

(c) Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.

(d) Turn the ignition switch to ON, and wait for at least 60 seconds.

(e) Clear the DTCs stored in memory.

Click here 2019 - 2020 MY RAV4 RAV4 HV [11/2018 - 08/2020]; SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM (w/o Occupant Classification System): DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs

(f) Turn the ignition switch off.

(g) Turn the ignition switch to ON, and wait for at least 60 seconds.

(h) Check for DTCs.

Click here 2019 - 2020 MY RAV4 RAV4 HV [11/2018 - 08/2020]; SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM (w/o Occupant Classification System): DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes

HINT:

Codes other than DTC B1642, B1643, B1647 and B1648 may be output at this time, but they are not related to this check.

(i) Turn the ignition switch off.

(j) Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 90 seconds.

(k) Return the No. 2 side airbag sensor assembly RH and LH to their original positions and connect the connectors to them.

DTC B1642 or B1643 is output

REPLACE NO. 2 SIDE AIRBAG SENSOR ASSEMBLY LH 2019 MY RAV4 RAV4 HV [11/2018 - 02/2019]; SUPPLEMENTAL RESTRAINT SYSTEMS: REAR AIRBAG SENSOR: REMOVAL 2019 MY RAV4 RAV4 HV [02/2019 - 10/2019]; SUPPLEMENTAL RESTRAINT SYSTEMS: REAR AIRBAG SENSOR: REMOVAL 2020 MY RAV4 RAV4 HV [10/2019 - 08/2020]; SUPPLEMENTAL RESTRAINT SYSTEMS: REAR AIRBAG SENSOR: REMOVAL

DTCs B1642, B1643, B1647 and B1648 are not output

USE SIMULATION METHOD TO CHECK

DTC B1647 or B1648 is output

5.

CHECK CONNECTION OF CONNECTOR

(a) Check that the connector is properly connected to the side airbag pressure sensor LH.

The connector is not properly connected

CONNECT CONNECTOR PROPERLY

The connector is properly connected

6.

CHECK CONNECTOR

(a) Disconnect the connectors from the No. 2 side airbag sensor assembly LH and side airbag pressure sensor LH.

*1

Side Airbag Pressure Sensor LH

*2

No. 2 Side Airbag Sensor Assembly LH

*3

Front Door Wire LH

*4

Floor Wire

(b) Check that the connector (on the side airbag pressure sensor LH side) is not damaged.

The connector is deformed or damaged

REPLACE FRONT DOOR WIRE LH

The connector is not deformed or damaged

7.

CHECK SIDE AIRBAG PRESSURE SENSOR LH CIRCUIT

(a) Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.

*1

Side Airbag Pressure Sensor LH

*2

No. 2 Side Airbag Sensor Assembly LH

*3

Front Door Wire LH

*4

Floor Wire

*5

Service Wire

*a

Front view of wire harness connector

(to Side Airbag Pressure Sensor LH)

*b

Front view of wire harness connector

(to No. 2 Side Airbag Sensor Assembly LH)

(b) Turn the ignition switch to ON.

(c) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Switch Condition

Specified Condition

J9-2 (BDL+) - Body ground

Ignition switch ON

Below 1 V

J9-1 (BDL-) - Body ground

Ignition switch ON

Below 1 V

(d) Turn the ignition switch off.

(e) Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 90 seconds.

(f) Using a service wire, connect terminals 1 (BDL+) and 2 (BDL-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.

(g) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

J9-2 (BDL+) - J9-1 (BDL-)

Always

Below 1 Ω

(h) Disconnect the service wire from connector B.

(i) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

J9-2 (BDL+) - J9-1 (BDL-)

Always

1 MΩ or higher

J9-2 (BDL+) - Body ground

Always

1 MΩ or higher

J9-1 (BDL-) - Body ground

Always

1 MΩ or higher

NG

GO TO STEP 9

OK

8.

CHECK SIDE AIRBAG PRESSURE SENSOR LH

(a) Connect the connector to the No. 2 side airbag sensor assembly LH.

*1

Side Airbag Pressure Sensor RH

*2

No. 2 Side Airbag Sensor Assembly LH

(b) Interchange the side airbag pressure sensor LH with RH and connect the connectors to them.

(c) Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.

(d) Turn the ignition switch to ON, and wait for at least 60 seconds.

(e) Clear the DTCs stored in memory.

Click here 2019 - 2020 MY RAV4 RAV4 HV [11/2018 - 08/2020]; SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM (w/o Occupant Classification System): DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs

(f) Turn the ignition switch off.

(g) Turn the ignition switch to ON, and wait for at least 60 seconds.

(h) Check for DTCs.

Click here 2019 - 2020 MY RAV4 RAV4 HV [11/2018 - 08/2020]; SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM (w/o Occupant Classification System): DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes

HINT:

Codes other than DTC B1642, B1643, B1647 and B1648 may be output at this time, but they are not related to this check.

(i) Turn the ignition switch off.

(j) Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 90 seconds.

(k) Return the side airbag pressure sensor RH and LH to their original positions and connect the connectors to them.

DTC B1647 or B1648 is output

REPLACE AIRBAG ECU ASSEMBLY 2019 MY RAV4 RAV4 HV [11/2018 - 02/2019]; SUPPLEMENTAL RESTRAINT SYSTEMS: CENTER AIRBAG SENSOR ASSEMBLY: REMOVAL 2019 MY RAV4 RAV4 HV [02/2019 - 10/2019]; SUPPLEMENTAL RESTRAINT SYSTEMS: CENTER AIRBAG SENSOR ASSEMBLY: REMOVAL 2020 MY RAV4 RAV4 HV [10/2019 - 08/2020]; SUPPLEMENTAL RESTRAINT SYSTEMS: CENTER AIRBAG SENSOR ASSEMBLY: REMOVAL

DTC B1642 or B1643 is output

REPLACE SIDE AIRBAG PRESSURE SENSOR LH 2019 MY RAV4 RAV4 HV [11/2018 - 02/2019]; SUPPLEMENTAL RESTRAINT SYSTEMS: SIDE AIRBAG SENSOR (for Front Door): REMOVAL 2019 MY RAV4 RAV4 HV [02/2019 - 10/2019]; SUPPLEMENTAL RESTRAINT SYSTEMS: SIDE AIRBAG SENSOR (for Front Door): REMOVAL 2020 MY RAV4 RAV4 HV [10/2019 - 08/2020]; SUPPLEMENTAL RESTRAINT SYSTEMS: SIDE AIRBAG SENSOR (for Front Door): REMOVAL

DTCs B1642, B1643, B1647 and B1648 are not output

USE SIMULATION METHOD TO CHECK

9.

CHECK CONNECTORS

(a) Disconnect the floor wire connector from the front door wire LH.

*1

Side Airbag Pressure Sensor LH

*2

No. 2 Side Airbag Sensor Assembly LH

*3

Front Door Wire LH

*4

Floor Wire

(b) Check that the connectors (on the floor wire side and front door wire LH side) are not damaged.

The connector is deformed or damaged

REPLACE FLOOR WIRE OR FRONT DOOR WIRE LH

The connector is not deformed or damaged

10.

CHECK FLOOR WIRE

(a) Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.

*1

Side Airbag Pressure Sensor LH

*2

No. 2 Side Airbag Sensor Assembly LH

*3

Front Door Wire LH

*4

Floor Wire

*5

Service Wire

*a

Front view of wire harness connector

(to Front Door Wire LH)

*b

Front view of wire harness connector

(to No. 2 Side Airbag Sensor Assembly LH)

(b) Turn the ignition switch to ON.

(c) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Switch Condition

Specified Condition

JN2-1 (BDL+) - Body ground

Ignition switch ON

Below 1 V

JN2-2 (BDL-) - Body ground

Ignition switch ON

Below 1 V

(d) Turn the ignition switch off.

(e) Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 90 seconds.

(f) Using a service wire, connect terminals 1 (BDL+) and 2 (BDL-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.

(g) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

JN2-1 (BDL+) - JN2-2 (BDL-)

Always

Below 1 Ω

(h) Disconnect the service wire from connector B.

(i) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

JN2-1 (BDL+) - JN2-2 (BDL-)

Always

1 MΩ or higher

JN2-1 (BDL+) - Body ground

Always

1 MΩ or higher

JN2-2 (BDL-) - Body ground

Always

1 MΩ or higher

OK

REPLACE FRONT DOOR WIRE LH

NG

REPLACE FLOOR WIRE