Last Modified: 01-30-2024 6.11:8.1.0 Doc ID: RM100000001FQQM
Model Year Start: 2019 Model: RAV4 Prod Date Range: [11/2018 - 02/2019]
Title: SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM (w/ Occupant Classification System): B1835-B1838; Short in Curtain Shield Airbag (LH) Squib Circuit; 2019 MY RAV4 RAV4 HV [11/2018 - 02/2019]

DTC

B1835

Short in Curtain Shield Airbag (LH) Squib Circuit

DTC

B1836

Open in Curtain Shield Airbag (LH) Squib Circuit

DTC

B1837

Short in Curtain Shield Airbag (LH) Squib Circuit (to Ground)

DTC

B1838

Short in Curtain Shield Airbag (LH) Squib Circuit (to +B)

DESCRIPTION

The curtain shield squib LH circuit consists of the airbag ECU assembly and curtain shield airbag assembly LH.

The circuit instructs the SRS to deploy when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the curtain shield squib LH circuit.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

Warning Indicate

Test Mode / Check Mode

B1835

Short in Curtain Shield Airbag (LH) Squib Circuit

One of the following conditions is met:

  • The airbag ECU assembly detects a line short circuit signal 5 times in the curtain shield squib LH circuit during the primary check.
  • A curtain shield airbag assembly LH malfunction.
  • An airbag ECU assembly malfunction.
  • Floor wire
  • Curtain shield airbag assembly LH
  • Airbag ECU assembly

Comes on

Applicable

B1836

Open in Curtain Shield Airbag (LH) Squib Circuit

One of the following conditions is met:

  • The airbag ECU assembly detects an open circuit signal in the curtain shield squib LH circuit for 2 seconds.
  • A curtain shield airbag assembly LH malfunction.
  • An airbag ECU assembly malfunction.
  • Floor wire
  • Curtain shield airbag assembly LH
  • Airbag ECU assembly

Comes on

Applicable

B1837

Short in Curtain Shield Airbag (LH) Squib Circuit (to Ground)

One of the following conditions is met:

  • The airbag ECU assembly detects a short circuit to ground signal in the curtain shield squib LH circuit for 0.5 seconds.
  • A curtain shield airbag assembly LH malfunction.
  • An airbag ECU assembly malfunction.
  • Floor wire
  • Curtain shield airbag assembly LH
  • Airbag ECU assembly

Comes on

Applicable

B1838

Short in Curtain Shield Airbag (LH) Squib Circuit (to +B)

One of the following conditions is met:

  • The airbag ECU assembly detects a short circuit to B+ signal in the curtain shield squib LH circuit for 0.5 seconds.
  • A curtain shield airbag assembly LH malfunction.
  • An airbag ECU assembly malfunction.
  • Floor wire
  • Curtain shield airbag assembly LH
  • Airbag ECU assembly

Comes on

Applicable

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

  • After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal.

    Click here 2019 MY RAV4 RAV4 HV [11/2018 - 02/2019]; INTRODUCTION: REPAIR INSTRUCTION: INITIALIZATION

  • When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.

    Click here 2019 MY RAV4 RAV4 HV [11/2018 - 02/2019]; INTRODUCTION: REPAIR INSTRUCTION: INITIALIZATION

  • After replacing the airbag ECU assembly, refer to initialization.

    Click here 2019 MY RAV4 RAV4 HV [11/2018 - 02/2019]; INTRODUCTION: REPAIR INSTRUCTION: INITIALIZATION

HINT:

To perform the simulation method, enter check mode (signal check) with the Techstream (Click here 2019 - 2020 MY RAV4 RAV4 HV [11/2018 - 08/2020]; SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM (w/ Occupant Classification System): CHECK MODE PROCEDURE ), and then wiggle each connector of the airbag system or drive the vehicle on various types of road (Click here 2019 - 2024 MY RAV4 RAV4 HV [11/2018 -        ]; INTRODUCTION: HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS: HOW TO PROCEED WITH TROUBLESHOOTING ).

PROCEDURE

1.

CHECK CONNECTORS

(a) Turn the ignition switch off.

*1

Curtain Shield Airbag Assembly LH

*2

Airbag ECU Assembly

*3

Floor Wire

(b) Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

(c) Check that the connectors are properly connected to the curtain shield airbag assembly LH and airbag ECU assembly.

OK:

The connectors are properly connected.

HINT:

If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.

(d) Disconnect the connectors from the curtain shield airbag assembly LH and airbag ECU assembly.

(e) Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.

(f) Check that the floor wire connector (on the curtain shield airbag assembly LH side) is not loose, deformed or damaged.

OK:

The connector locking button is not disengaged, and the claw of the lock is not deformed or damaged.

(g) Check that the short springs of the activation prevention mechanism of the floor wire connector are not deformed or damaged.

OK:

The short springs are not deformed or damaged.

NG

REPLACE FLOOR WIRE

OK

2.

CHECK CURTAIN SHIELD AIRBAG ASSEMBLY LH

(a) Connect the connector to the airbag ECU assembly.

*1

Curtain Shield Airbag Assembly LH

*2

Airbag ECU Assembly

*3

SST

*a

Front view of wire harness connector

(to Curtain Shield Airbag Assembly LH)

(b) Connect the white wire side of SST (resistance: 2.1 Ω) to connector C.

CAUTION:

Never connect the tester to the curtain shield airbag assembly LH for measurement, as this may lead to a serious injury due to airbag deployment.

NOTICE:

  • Do not forcibly insert SST into the terminals of the connector when connecting SST.
  • Insert SST straight into the terminals of the connector.

SST: 09843-18061

(c) Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

(d) Turn the ignition switch to ON, and wait for at least 60 seconds.

(e) Clear the DTCs stored in memory.

Click here 2019 - 2020 MY RAV4 RAV4 HV [11/2018 - 08/2020]; SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM (w/ Occupant Classification System): DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs

(f) Turn the ignition switch off.

(g) Turn the ignition switch to ON, and wait for at least 60 seconds.

(h) Check for DTCs.

Click here 2019 - 2020 MY RAV4 RAV4 HV [11/2018 - 08/2020]; SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM (w/ Occupant Classification System): DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes

HINT:

Codes other than DTC B1835, B1836, B1837 and B1838 may be output at this time, but they are not related to this check.

(i) Turn the ignition switch off.

(j) Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

(k) Disconnect SST from connector C.

DTCs B1835, B1836, B1837 and B1838 are not output

REPLACE CURTAIN SHIELD AIRBAG ASSEMBLY LH

DTC B1835, B1836, B1837 or B1838 is output

3.

CHECK FLOOR WIRE

(a) Disconnect the floor wire from the airbag ECU assembly.

*1

Curtain Shield Airbag Assembly LH

*2

Airbag ECU Assembly

*3

Floor Wire

*a

Front view of wire harness connector

(to Curtain Shield Airbag Assembly LH)

Release the activation prevention mechanism

(b) Check for a short to B+ in the circuit.

(1) Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

(2) Turn the ignition switch to ON.

(3) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Switch Condition

Specified Condition

N34-1 (ICL+) - Body ground

Ignition switch ON

Below 1 V

N34-2 (ICL-) - Body ground

Ignition switch ON

Below 1 V

(4) Turn the ignition switch off.

(5) Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

(c) Check for an open in the circuit.

(1) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

N34-1 (ICL+) - N34-2 (ICL-)

Always

Below 1 Ω

(d) Check for a short to ground in the circuit.

(1) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

N34-1 (ICL+) - Body ground

Always

1 MΩ or higher

N34-2 (ICL-) - Body ground

Always

1 MΩ or higher

(e) Check for a short in the circuit.

(1) Release the activation prevention mechanism built into connector B.

Click here 2019 - 2020 MY RAV4 RAV4 HV [11/2018 - 08/2020]; SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM (w/ Occupant Classification System): SYSTEM DESCRIPTION

(2) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

N34-1 (ICL+) - N34-2 (ICL-)

Always

1 MΩ or higher

(3) Restore the released activation prevention mechanism of connector B to the original condition.

NG

REPLACE FLOOR WIRE

OK

4.

CHECK DTC

(a) Connect the connectors to the curtain shield airbag assembly LH and airbag ECU assembly.

*1

Curtain Shield Airbag Assembly LH

*2

Airbag ECU Assembly

(b) Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

(c) Turn the ignition switch to ON, and wait for at least 60 seconds.

(d) Clear the DTCs stored in memory.

Click here 2019 - 2020 MY RAV4 RAV4 HV [11/2018 - 08/2020]; SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM (w/ Occupant Classification System): DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs

(e) Turn the ignition switch off.

(f) Turn the ignition switch to ON, and wait for at least 60 seconds.

(g) Check for DTCs.

Click here 2019 - 2020 MY RAV4 RAV4 HV [11/2018 - 08/2020]; SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM (w/ Occupant Classification System): DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes

HINT:

Codes other than DTC B1835, B1836, B1837 and B1838 may be output at this time, but they are not related to this check.

DTCs B1835, B1836, B1837 and B1838 are not output

USE SIMULATION METHOD TO CHECK

DTC B1835, B1836, B1837 or B1838 is output

REPLACE AIRBAG ECU ASSEMBLY