| Last Modified: 01-30-2024 | 6.11:8.1.0 | Doc ID: RM100000001FQP3 |
| Model Year Start: 2019 | Model: RAV4 | Prod Date Range: [11/2018 - 10/2023] |
| Title: DOOR / HATCH: POWER BACK DOOR SYSTEM (for Gasoline Model): B222B; PBD Touch Sensor RH Circuit; 2019 - 2023 MY RAV4 [11/2018 - 10/2023] | ||
|
DTC |
B222B |
PBD Touch Sensor RH Circuit |
DESCRIPTION
This DTC is output when the multiplex network door ECU detects a power back door sensor assembly RH touch sensor malfunction.
|
DTC No. |
Detection Item |
DTC Detection Condition |
Trouble Area |
|---|---|---|---|
|
B222B |
PBD Touch Sensor RH Circuit |
Multiplex network door ECU detects power back door sensor assembly RH touch sensor malfunction |
|
WIRING DIAGRAM
CAUTION / NOTICE / HINT
NOTICE:
If the replacement, removal and installation of the multiplex network door ECU or disconnection of the connectors of the multiplex network door ECU has been performed, initialize the power back door system.
Click here
![2019 - 2023 MY RAV4 [11/2018 - 10/2023]; DOOR / HATCH: POWER BACK DOOR SYSTEM (for Gasoline Model): INITIALIZATION](/t3Portal/stylegraphics/info.gif)
PROCEDURE
|
1. |
CHECK FOR DTC |
(a) Clear the DTCs.
Click here
Body Electrical > Back Door > Clear DTCs
(b) Check for DTCs.
Click here
Body Electrical > Back Door > Trouble Codes
OK:
DTC B222B is not output.
| OK |
|
|
|
2. |
READ VALUE USING TECHSTREAM |
(a) Read the Data List according to the display on the Techstream.
Click here
Body Electrical > Back Door > Data List
|
Tester Display |
Measurement Item |
Range |
Normal Condition |
Diagnostic Note |
|---|---|---|---|---|
|
PBD Touch Sensor (Right) |
Power back door sensor assembly RH signal |
ON, OFF or Open |
ON: Power back door sensor assembly RH pressed OFF: Power back door sensor assembly RH not pressed Open: Power back door sensor assembly RH circuit open |
- |
Body Electrical > Back Door > Data List
|
Tester Display |
|---|
|
PBD Touch Sensor (Right) |
|
Result |
Proceed to |
|---|---|
|
On the Techstream screen, ON or OFF is displayed accordingly |
A |
|
On the Techstream screen, ON or OFF is not displayed accordingly or Open is displayed for power back door sensor assembly RH |
B |
| A |
|
|
|
3. |
INSPECT POWER BACK DOOR SENSOR ASSEMBLY RH |
(a) Remove the power back door sensor assembly RH.
Click here
(b) Inspect the power back door sensor assembly RH.
Click here
| NG |
|
|
|
4. |
CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK DOOR ECU - POWER BACK DOOR SENSOR ASSEMBLY RH) |
(a) Disconnect the R18 multiplex network door ECU connector.
(b) Disconnect the R8 power back door sensor assembly RH connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
R18-6 (OSR) - R8-1 (OSR) |
Always |
Below 1 Ω |
|
R18-24 (OSE) - R8-2 (OSRE) |
Always |
Below 1 Ω |
|
R18-6 (OSR) or R8-1 (OSR) - Body ground |
Always |
10 kΩ or higher |
|
R18-24 (OSE) or R8-2 (OSRE) - Body ground |
Always |
10 kΩ or higher |
| OK |
|
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|