| Last Modified: 01-30-2024 | 6.11:8.1.0 | Doc ID: RM100000001FP57 |
| Model Year Start: 2019 | Model: RAV4 | Prod Date Range: [11/2018 - 10/2022] |
| Title: METER / GAUGE / DISPLAY: METER / GAUGE SYSTEM: B132187; Lost Communication with EMV Missing Message; 2019 - 2022 MY RAV4 RAV4 HV [11/2018 - 10/2022] | ||
|
DTC |
B132187 |
Lost Communication with EMV Missing Message |
DESCRIPTION
The combination meter assembly and radio and display receiver assembly communicate via local bus communication. This allows audio and visual system information to be displayed on the multi-information display. This DTC is stored when a communication error occurs between the radio and display receiver assembly and combination meter assembly.
|
DTC No. |
Detection Item |
DTC Detection Condition |
Trouble Area |
|---|---|---|---|
|
B132187 |
Lost Communication with EMV Missing Message |
Diagnosis Condition:
Malfunction Status:
Malfunction Time:
|
|
WIRING DIAGRAM
CAUTION / NOTICE / HINT
NOTICE:
- When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.
-
When replacing the radio and display receiver assembly, always replace it with a new one. If a radio and display receiver assembly which was installed to another vehicle is used, the following may occur:
- A communication malfunction DTC may be stored.
- The radio and display receiver assembly may not operate normally.
PROCEDURE
|
1. |
CHECK CAN MAIN WIRE (COMBINATION METER ASSEMBLY CAN MAIN WIRE) |
(a) Disconnect the cable from the negative (-) auxiliary battery terminal.
(b) Disconnect the G18 combination meter assembly connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
G18-27 (MSCH) - G18-10 (MSCL) |
Cable disconnected from negative (-) auxiliary battery terminal |
108 to 132 Ω |
|
G18-27 (MSCH) - G114-4 (CG) |
Cable disconnected from negative (-) auxiliary battery terminal |
200 Ω or higher |
|
G18-10 (MSCL) - G114-4 (CG) |
Cable disconnected from negative (-) auxiliary battery terminal |
200 Ω or higher |
|
G18-27 (MSCH) - G114-16 (BAT) |
Cable disconnected from negative (-) auxiliary battery terminal |
6 kΩ or higher |
|
G18-10 (MSCL) - G114-16 (BAT) |
Cable disconnected from negative (-) auxiliary battery terminal |
6 kΩ or higher |
| NG |
|
|
|
2. |
CHECK COMBINATION METER ASSEMBLY |
(a) Replace the combination meter assembly.
Click here
![2019 - 2022 MY RAV4 RAV4 HV [11/2018 - 10/2022]; METER / GAUGE / DISPLAY: COMBINATION METER: REMOVAL](/t3Portal/stylegraphics/info.gif)
(b) Clear the DTCs.
Click here
Body Electrical > Combination Meter > Clear DTCs
(c) Make sure that the DTC detection conditions are met.
HINT:
If the detection conditions are not met, the system cannot detect the malfunction.
(d) Recheck for DTCs and check that no DTCs are output.
Click here
Body Electrical > Combination Meter > Trouble Codes
OK:
DTC B132187 is not output.
| OK |
|
END (COMBINATION METER ASSEMBLY WAS DEFECTIVE) |
| NG |
|
|
3. |
CHECK CAN MAIN WIRE (RADIO AND DISPLAY RECEIVER ASSEMBLY CAN MAIN WIRE) |
(a) Reconnect the G18 combination meter assembly connector.
(b) Disconnect the G2 radio and display receiver assembly connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
G2-5 (CNH1) - G2-6 (CNL1) |
Cable disconnected from negative (-) auxiliary battery terminal |
108 to 132 Ω |
|
G2-5 (CNH1) - G114-4 (CG) |
Cable disconnected from negative (-) auxiliary battery terminal |
200 Ω or higher |
|
G2-6 (CNL1) - G114-4 (CG) |
Cable disconnected from negative (-) auxiliary battery terminal |
200 Ω or higher |
|
G2-5 (CNH1) - G114-16 (BAT) |
Cable disconnected from negative (-) auxiliary battery terminal |
6 kΩ or higher |
|
G2-6 (CNL1) - G114-16 (BAT) |
Cable disconnected from negative (-) auxiliary battery terminal |
6 kΩ or higher |
| NG |
|
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR |
|
|
4. |
CHECK COMBINATION METER ASSEMBLY |
(a) Replace the combination meter assembly.
Click here
(b) Clear the DTCs.
Click here
Body Electrical > Combination Meter > Clear DTCs
(c) Make sure that the DTC detection conditions are met.
HINT:
If the detection conditions are not met, the system cannot detect the malfunction.
(d) Recheck for DTCs and check that no DTCs are output.
Click here
Body Electrical > Combination Meter > Trouble Codes
OK:
DTC B132187 is not output.
| OK |
|
END (COMBINATION METER ASSEMBLY WAS DEFECTIVE) |
| NG |
|
|
|