Last Modified: 01-30-2024 6.11:8.1.0 Doc ID: RM100000001FMS4
Model Year Start: 2019 Model: RAV4 Prod Date Range: [11/2018 - 08/2020]
Title: A25A-FKS (ENGINE CONTROL): SFI SYSTEM (w/o Canister Pump Module): P0A1414; Engine Mount "A" Control Circuit Low Circuit Short to Ground or Open; 2019 - 2020 MY RAV4 [11/2018 - 08/2020]

DTC

P0A1414

Engine Mount "A" Control Circuit Low Circuit Short to Ground or Open

DESCRIPTION

Refer to DTC P0A1412.

Click here 2019 - 2020 MY RAV4 [11/2018 - 08/2020]; A25A-FKS (ENGINE CONTROL): SFI SYSTEM (w/o Canister Pump Module): P0A1412; Engine Mount "A" Control Circuit High Circuit Short to Battery+

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

MIL

Memory

Note

P0A1414

Engine Mount "A" Control Circuit Low Circuit Short to Ground or Open

Open or short in vacuum switching valve (for active control engine mount system) circuit and power supply circuit

(2 trip detection logic).
  • Open or short in vacuum switching valve (for active control engine mount system) circuit
  • Vacuum switching valve (for active control engine mount system)
  • ECM

Does not come on

DTC stored

SAE Code: P0A15

MONITOR DESCRIPTION

The ECM monitors the output voltage while the vacuum switching valve (for active control engine mount system) is operating.

The vacuum switching valve (for active control engine mount system) turns on and off according to ON/OFF switching of a transistor inside the ECM.

If a continuous mismatch occurs between the ECM transistor state and the output voltage, the ECM determines there is a malfunction in the vacuum switching valve (for active control engine mount system) circuit and stores a DTC.

MONITOR STRATEGY

Frequency of Operation

Continuous

CONFIRMATION DRIVING PATTERN

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON.
  3. Turn the Techstream on.
  4. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  5. Turn the ignition switch off and wait for at least 30 seconds.
  6. Turn the ignition switch to ON.
  7. Turn the Techstream on.
  8. Enter the following menus: Powertrain / Engine / Active Test / Activate the ACM Inhibit.
  9. In the Active Test, wait for at least 5 seconds with the vacuum switching valve (for active control engine mount system) at ON.
  10. In the Active Test, wait for at least 5 seconds with the vacuum switching valve (for active control engine mount system) at OFF.
  11. Enter the following menus: Powertrain / Engine / Trouble Codes.
  12. Read the pending DTCs.

    HINT:

    • If a pending DTC is output, the system is malfunctioning.
    • If a pending DTC is not output, perform the following procedure.
  13. Enter the following menus: Powertrain / Engine / Utility / All Readiness.
  14. Input the DTC: P0A1414.
  15. Check the DTC judgment result.

    Techstream Display

    Description

    NORMAL
    • DTC judgment completed
    • System normal

    ABNORMAL
    • DTC judgment completed
    • System abnormal

    INCOMPLETE
    • DTC judgment not completed
    • Perform driving pattern after confirming DTC enabling conditions

    HINT:

    • If the judgment result is NORMAL, the system is normal.
    • If the judgment result is ABNORMAL, the system has a malfunction.

WIRING DIAGRAM

Refer to DTC P0A1412.

Click here 2019 - 2020 MY RAV4 [11/2018 - 08/2020]; A25A-FKS (ENGINE CONTROL): SFI SYSTEM (w/o Canister Pump Module): P0A1412; Engine Mount "A" Control Circuit High Circuit Short to Battery+

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.

HINT:

Read Freeze Frame Data using the Techstream. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

PROCEDURE

1.

CHECK TERMINAL VOLTAGE (POWER SOURCE OF VACUUM SWITCHING VALVE (FOR ACTIVE CONTROL ENGINE MOUNT SYSTEM))

*a

Front view of wire harness connector

(to Vacuum Switching Valve (for Active Control Engine Mount System))

(a) Disconnect the vacuum switching valve (for active control engine mount system) connector.

(b) Turn the ignition switch to ON.

(c) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Condition

Specified Condition

C7-1 - Body ground

Ignition switch ON

11 to 14 V
NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (VACUUM SWITCHING VALVE (FOR ACTIVE CONTROL ENGINE MOUNT SYSTEM) - EFI-MAIN NO. 1 RELAY)
OK

2.

INSPECT VACUUM SWITCHING VALVE (FOR ACTIVE CONTROL ENGINE MOUNT SYSTEM)

(a) Inspect the vacuum switching valve (for active control engine mount system).

Click here 2019 - 2024 MY RAV4 [11/2018 -        ]; A25A-FKS (ENGINE CONTROL): VACUUM SWITCHING VALVE (for Engine Mounting): INSPECTION

NG

REPLACE VACUUM SWITCHING VALVE (FOR ACTIVE CONTROL ENGINE MOUNT SYSTEM)

OK

3.

CHECK HARNESS AND CONNECTOR (VACUUM SWITCHING VALVE (FOR ACTIVE CONTROL ENGINE MOUNT SYSTEM) - ECM)

(a) Disconnect the vacuum switching valve (for active control engine mount system) connector.

(b) Disconnect the ECM connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

C7-2 - C40-44 (ACM)

Always

Below 1 Ω

C7-2 or C40-44 (ACM) - Body ground and other terminals

Always

10 kΩ or higher
OK

REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR