| Last Modified: 01-30-2024 | 6.11:8.1.0 | Doc ID: RM100000001FJ0A |
| Model Year Start: 2019 | Model: RAV4 | Prod Date Range: [11/2018 - ] |
| Title: WINDOW / GLASS: POWER WINDOW CONTROL SYSTEM: Front Passenger Side Power Window Auto Up / Down Function does not Operate with Front Passenger Side Power Window Switch; 2019 - 2024 MY RAV4 RAV4 HV [11/2018 - ] | ||
|
Front Passenger Side Power Window Auto Up / Down Function does not Operate with Front Passenger Side Power Window Switch |
DESCRIPTION
If the manual up and down function operates normally but the auto up and down function does not, then fail-safe mode may be functioning.
If power window initialization has not been performed, the auto up and down function will not operate.
Click here
![2019 - 2024 MY RAV4 RAV4 HV [11/2018 - ]; WINDOW / GLASS: POWER WINDOW CONTROL SYSTEM: INITIALIZATION](/t3Portal/stylegraphics/info.gif)
WIRING DIAGRAM
CAUTION / NOTICE / HINT
NOTICE:
-
If the front power window regulator motor assembly has been replaced with a new one, initialize the power window control system.
Click here
-
Check that the "P Window Auto Up" and "P Window Auto Down" power window control system customize settings are "ON" before proceeding with work.
Click here
- After the catch protection function operates, the auto operation is not performed the first time auto up is performed. All auto up operations performed after the first operate normally.
HINT:
If the pulse sensor built into the front power window regulator motor assembly is malfunctioning, the power window control system enters fail-safe mode. The remote up and down and auto up and down functions cannot be operated during fail-safe mode. However, the power window can be closed by holding the power window regulator switch assembly at the auto up position, and opened manually by pushing down the power window regulator switch assembly.
Click here
PROCEDURE
|
1. |
READ VALUE USING TECHSTREAM (P-DOOR MOTOR) |
(a) Using the Techstream, read the data for the condition when the power window regulator switch assembly was operated.
Click here
Body Electrical > P-Door Motor > Data List
|
Tester Display |
Measurement Item |
Range |
Normal Condition |
Diagnostic Note |
|---|---|---|---|---|
|
P Door P/W Auto SW |
Front passenger door power window auto switch signal |
OFF or ON |
OFF: Front passenger door power window auto switch not being operated ON: Front passenger door power window auto switch being operated |
- |
Body Electrical > P-Door Motor > Data List
|
Tester Display |
|---|
|
P Door P/W Auto SW |
OK:
On the Techstream screen, ON or OFF is displayed accordingly.
| NG |
|
|
|
2. |
PERFORM INITIALIZATION |
(a) Initialize the front power window regulator motor assembly RH.
Click here
OK:
Power window system operates normally.
| OK |
|
END (PROBLEM DUE TO INITIALIZATION FAILURE) |
| NG |
|
REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH
|
|
3. |
INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY |
(a) Remove the power window regulator switch assembly.
Click here
(b) Inspect the power window regulator switch assembly.
Click here
| NG |
|
|
|
4. |
CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH) |
(a) Disconnect the I3 power window regulator switch assembly connector.
(b) Disconnect the I7 front power window regulator motor assembly RH connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
I3-8 (AUTO) - I7-4 (AUTO) |
Always |
Below 1 Ω |
|
I3-8 (AUTO) or I7-4 (AUTO) - Body ground |
Always |
10 kΩ or higher |
| OK |
|
REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH
|
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|