Last Modified: 01-30-2024 6.11:8.1.0 Doc ID: RM100000001FHH8
Model Year Start: 2019 Model: RAV4 HV Prod Date Range: [11/2018 - 08/2020]
Title: A25A-FXS (ENGINE CONTROL): SFI SYSTEM (w/o Canister Pump Module): P060E49; Internal Control Module Throttle Position Performance Internal Electronic Failure; 2019 - 2020 MY RAV4 HV [11/2018 - 08/2020]

DTC

P060E49

Internal Control Module Throttle Position Performance Internal Electronic Failure

MONITOR DESCRIPTION

The ECM monitors the signals received from the No. 1 throttle position sensor. As the ECM monitors the VTA1 signal of the No. 1 throttle position sensor, if these signals do not correlate, a DTC will be stored.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

MIL

Memory

Note

P060E49

Internal Control Module Throttle Position Performance Internal Electronic Failure

Either of the following conditions is met (1 trip detection logic):

  • ECM main CPU malfunction.
  • ECM sub CPU malfunction.

ECM

Comes on

DTC stored

SAE Code: P060E

MONITOR STRATEGY

Required Sensors/Components

ECM

Frequency of Operation

Continuous

CONFIRMATION DRIVING PATTERN

  1. Connect the Techstream to the DLC3.
  2. Turn the power switch on (IG).
  3. Turn the Techstream on.
  4. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  5. Turn the Techstream off.
  6. Turn the power switch off.
  7. Disconnect the Techstream.
  8. Disconnect the cable from the negative (-) auxiliary battery terminal and wait for 1 minute.
  9. Connect the cable to the negative (-) auxiliary battery terminal.
  10. Connect the Techstream to the DLC3.
  11. Turn the power switch on (IG).
  12. Turn the Techstream on.
  13. Wait 16 seconds or more.
  14. Enter the following menus: Powertrain / Engine / Trouble Codes.
  15. Read the pending DTCs.

    HINT:

    • If a pending DTC is output, the system is malfunctioning.
    • If a pending DTC is not output, perform the following procedure.
  16. Enter the following menus: Powertrain / Engine / Utility / All Readiness.
  17. Input the DTC: P060E49.
  18. Check the DTC judgment result.

    Techstream Display

    Description

    NORMAL
    • DTC judgment completed
    • System normal

    ABNORMAL
    • DTC judgment completed
    • System abnormal

    INCOMPLETE
    • DTC judgment not completed
    • Perform driving pattern after confirming DTC enabling conditions

    HINT:

    • If the judgment result is NORMAL, the system is normal.
    • If the judgment result is ABNORMAL, the system is malfunctioning.

CAUTION / NOTICE / HINT

NOTICE:

  • After turning power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

    Click here 2019 - 2024 MY RAV4 RAV4 HV [11/2018 -        ]; INTRODUCTION: REPAIR INSTRUCTION: PRECAUTION

  • Vehicle Control History may be stored in the hybrid vehicle control ECU assembly if the engine is malfunctioning. Certain vehicle condition information is recorded when Vehicle Control History is stored. Reading the vehicle conditions recorded in both the freeze frame data and Vehicle Control History can be useful for troubleshooting.

    Click here 2019 - 2020 MY RAV4 HV [11/2018 - 08/2020]; HYBRID / BATTERY CONTROL: HYBRID CONTROL SYSTEM (for 2WD with NICKEL METAL HYDRIDE BATTERY): VEHICLE CONTROL HISTORY

    (Select Powertrain in Health Check and then check the time stamp data.)

    Click here 2019 - 2020 MY RAV4 HV [11/2018 - 08/2020]; A25A-FXS (ENGINE CONTROL): SFI SYSTEM (w/o Canister Pump Module): DTC CHECK / CLEAR

  • If any "Engine Malfunction" Vehicle Control History item has been stored in the hybrid vehicle control ECU assembly, make sure to clear it. However, as all Vehicle Control History items are cleared simultaneously, if any Vehicle Control History items other than "Engine Malfunction" are stored, make sure to perform any troubleshooting for them before clearing Vehicle Control History.

    Click here 2019 - 2020 MY RAV4 HV [11/2018 - 08/2020]; HYBRID / BATTERY CONTROL: HYBRID CONTROL SYSTEM (for 2WD with NICKEL METAL HYDRIDE BATTERY): VEHICLE CONTROL HISTORY

HINT:

Read Freeze Frame Data using the Techstream. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

PROCEDURE

1.

CLEAR DTC

(a) Connect the Techstream to the DLC3.

(b) Turn the power switch on (IG).

(c) Turn the Techstream on.

(d) Clear the DTCs.

Powertrain > Engine > Clear DTCs

(e) Turn the power switch off.

NEXT

2.

READ OUTPUT DTC (DTC P060E49)

(a) Disconnect the cable from the negative (-) auxiliary battery terminal and wait for 1 minute.

(b) Connect the cable to the negative (-) auxiliary battery terminal.

(c) Connect the Techstream to the DLC3.

(d) Turn the power switch on (IG).

(e) Turn the Techstream on.

(f) Wait 16 seconds or more.

(g) Enter the following menus: Powertrain / Engine / Trouble Codes.

(h) Read the DTCs.

Powertrain > Engine > Trouble Codes

Result

Proceed to

DTCs are not output

A

DTC P060E49 is output

B
A

CHECK FOR INTERMITTENT PROBLEMS

B

REPLACE ECM 2019 MY RAV4 HV [11/2018 - 02/2019]; A25A-FXS (ENGINE CONTROL): ECM: REMOVAL 2019 - 2020 MY RAV4 HV [02/2019 - 08/2020]; A25A-FXS (ENGINE CONTROL): ECM: REMOVAL