| Last Modified: 01-30-2024 | 6.11:8.1.0 | Doc ID: RM100000001FEZU |
| Model Year Start: 2019 | Model: RAV4 HV | Prod Date Range: [11/2018 - 10/2019] |
| Title: P710 (HYBRID TRANSMISSION / TRANSAXLE): HYBRID TRANSAXLE FLUID: ADJUSTMENT; 2019 MY RAV4 HV [11/2018 - 10/2019] | ||
ADJUSTMENT
PROCEDURE
1. REMOVE FRONT FENDER FRONT SPLASH SHIELD LH
Click here
![2019 MY RAV4 HV [11/2018 - 02/2019]; A25A-FXS (ENGINE MECHANICAL): ENGINE ASSEMBLY: REMOVAL+](/t3Portal/stylegraphics/info.gif)
2. REMOVE FRONT FENDER FRONT SPLASH SHIELD RH
Click here
3. REMOVE NO. 1 ENGINE UNDER COVER
Click here
4. REMOVE NO. 2 ENGINE UNDER COVER ASSEMBLY
Click here
5. REMOVE FRONT FENDER APRON SEAL LH
Click here
6. DRAIN HYBRID TRANSAXLE FLUID
|
(a) Using a 10 mm hexagon socket wrench, remove the filler plug and gasket from the hybrid vehicle transaxle assembly. |
|
|
(b) Using a 10 mm hexagon socket wrench, remove the drain plug and gasket from the hybrid vehicle transaxle assembly and drain the hybrid transaxle fluid. |
|
(c) Using a 10 mm hexagon socket wrench, install the drain plug and a new gasket to the hybrid vehicle transaxle assembly.
Torque:
50 N·m {510 kgf·cm, 37 ft·lbf}
(d) Using a 10 mm hexagon socket wrench, temporarily install the filler plug and gasket to the hybrid vehicle transaxle assembly.
HINT:
Reuse the old gasket as the filler plug will be removed again.
7. ADD HYBRID TRANSAXLE FLUID
|
(a) Using a 10 mm hexagon socket wrench, remove the filler plug and gasket from the hybrid vehicle transaxle assembly. |
|
(b) Add hybrid transaxle fluid until the hybrid transaxle fluid level is between 0 to 10 mm (0 to 0.394 in.) from the bottom lip of the filler plug opening. [#]
NOTICE:
- When adding hybrid transaxle fluid, make sure that the vehicle is level.
- Use Toyota Genuine ATF WS.
- Be sure to fully insert the filler nozzle into the filler plug opening.
- Be sure to add hybrid transaxle fluid slowly. If hybrid transaxle fluid is added quickly, the hybrid transaxle fluid may hit internal parts and bounce back, resulting in hybrid transaxle fluid coming out of the filler plug opening.
- Be sure to directly check that the hybrid transaxle fluid level is within the specified range.
- Driving the vehicle with an insufficient or excessive amount of hybrid transaxle fluid may damage the hybrid vehicle transaxle assembly.
Hybrid Transaxle Fluid Standard Capacity (for Reference):
3.9 liters (4.1 US qts, 3.4 Imp. qts)
(c) After adding hybrid transaxle fluid, leave the vehicle for 30 seconds so that the hybrid transaxle fluid surface can become still again, and then check that the hybrid transaxle fluid level is between 0 to 10 mm (0 to 0.394 in.) from the bottom lip of the filler plug opening. (If the hybrid transaxle fluid level is low, repeat this procedure from step [#].)
NOTICE:
After adding hybrid transaxle fluid, make sure to check the hybrid transaxle fluid level.
(d) Using a 10 mm hexagon socket wrench, temporarily install the filler plug and gasket to the hybrid vehicle transaxle assembly.
HINT:
Reuse the old gasket as the filler plug will be removed again.
8. INSPECT HYBRID TRANSAXLE FLUID
Click here
9. INSPECT FOR HYBRID TRANSAXLE FLUID LEAK
10. INSTALL FRONT FENDER APRON SEAL LH
Click here
11. INSTALL NO. 2 ENGINE UNDER COVER ASSEMBLY
Click here
12. INSTALL NO. 1 ENGINE UNDER COVER
Click here
13. INSTALL FRONT FENDER FRONT SPLASH SHIELD RH
Click here
14. INSTALL FRONT FENDER FRONT SPLASH SHIELD LH
Click here
|
|