| Last Modified: 01-30-2024 | 6.11:8.1.0 | Doc ID: RM100000001FAI2 |
| Model Year Start: 2019 | Model: RAV4 | Prod Date Range: [11/2018 - ] |
| Title: PARK ASSIST / MONITORING: BLIND SPOT MONITOR SYSTEM: C1ABE; Short to GND or Open in Buzzer; 2019 - 2024 MY RAV4 RAV4 HV [11/2018 - ] | ||
|
DTC |
C1ABE |
Short to GND or Open in Buzzer |
DESCRIPTION
DTC C1ABE is stored when the blind spot monitor sensor RH detects a short to ground or open in the RCTA buzzer (blind spot monitor buzzer) circuit.
|
DTC No. |
Detection Item |
DTC Detection Condition |
Trouble Area |
|---|---|---|---|
|
C1ABE |
Short to GND or Open in Buzzer |
Both of the following conditions are met:
|
|
WIRING DIAGRAM
CAUTION / NOTICE / HINT
NOTICE:
- When checking for DTCs, make sure that the blind spot monitor system is turned on.
- Inspect the fuses for circuits related to this system before performing the following procedure.
PROCEDURE
|
1. |
CHECK DTC |
(a) Turn the ignition switch off.
(b) Turn the ignition switch to ON.
(c) Recheck for DTCs and check if the same DTC is output again.
Click here
![2019 - 2024 MY RAV4 RAV4 HV [11/2018 - ]; PARK ASSIST / MONITORING: BLIND SPOT MONITOR SYSTEM: DTC CHECK / CLEAR](/t3Portal/stylegraphics/info.gif)
Body Electrical > Blind Spot Monitor Slave > Trouble Codes
OK:
No DTCs are output.
| OK |
|
|
|
2. |
CHECK HARNESS AND CONNECTOR (RCTA BUZZER [BLIND SPOT MONITOR BUZZER] - AUXILIARY BATTERY AND BLIND SPOT MONITOR SENSOR RH) |
(a) Disconnect the N19 RCTA buzzer (blind spot monitor buzzer) connector.
(b) Disconnect the Q13 blind spot monitor sensor RH connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
N19-2 (BZN) - Q13-3 (BUZ) |
Always |
Below 1 Ω |
|
N19-2 (BZN) - Body ground |
Always |
10 kΩ or higher |
(d) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
|
Tester Connection |
Switch Condition |
Specified Condition |
|---|---|---|
|
N19-1 (BZP) - Body ground |
Ignition switch ON |
11 to 14 V |
|
N19-1 (BZP) - Body ground |
Ignition switch off |
Below 1 V |
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
3. |
CHECK RCTA BUZZER (BLIND SPOT MONITOR BUZZER) |
(a) Replace the RCTA buzzer (blind spot monitor buzzer) with a new or known good one.
Click here
(b) Clear the DTCs.
Click here
Body Electrical > Blind Spot Monitor Slave > Clear DTCs
(c) Recheck for DTCs and check if the same DTC is output again.
Click here
Body Electrical > Blind Spot Monitor Slave > Trouble Codes
OK:
No DTCs are output.
| OK |
|
END (RCTA BUZZER [BLIND SPOT MONITOR BUZZER] WAS DEFECTIVE) |
| NG |
|
REPLACE BLIND SPOT MONITOR SENSOR RH
|
|
|