Last Modified: 01-30-2024 6.11:8.1.0 Doc ID: RM100000001FAHS
Model Year Start: 2019 Model: RAV4 Prod Date Range: [11/2018 -           ]
Title: PARK ASSIST / MONITORING: BLIND SPOT MONITOR SYSTEM: C1AB1; Short to +B in Outer Mirror Indicator(Slave); 2019 - 2024 MY RAV4 RAV4 HV [11/2018 -        ]

DTC

C1AB1

Short to +B in Outer Mirror Indicator(Slave)

DESCRIPTION

This DTC is stored when the blind spot monitor sensor RH detects a short to +B in the outer rear view mirror indicator RH.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

C1AB1

Short to +B in Outer Mirror Indicator(Slave)

Both of the following conditions are met:

  • The blind spot monitor system is on
  • The blind spot monitor sensor is not sending voltage to the indicator but the indicator receives voltage above a specified level for a specified period of time
  • Outer mirror RH (outer rear view mirror indicator RH)
  • Outer rear view mirror assembly RH
  • Harness or connector
  • Blind spot monitor sensor RH

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

When checking for DTCs, make sure that the blind spot monitor system is turned on.

PROCEDURE

1.

CHECK DTC

(a) Turn the ignition switch off.

(b) Turn the ignition switch to ON.

(c) Recheck for DTCs and check if the same DTC is output again.

Click here 2019 - 2024 MY RAV4 RAV4 HV [11/2018 -        ]; PARK ASSIST / MONITORING: BLIND SPOT MONITOR SYSTEM: DTC CHECK / CLEAR

Body Electrical > Blind Spot Monitor Slave > Trouble Codes

OK:

No DTCs are output.

OK

USE SIMULATION METHOD TO CHECK

NG

2.

CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR INDICATOR CIRCUIT)

(a) Disconnect the blind spot monitor sensor RH connector.

*a

Front view of wire harness connector

(to Blind Spot Monitor Sensor RH)

(b) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Switch Condition

Specified Condition

Q13-4 (OMIR) - Body ground

Ignition switch ON

Below 1 V
OK

REPLACE BLIND SPOT MONITOR SENSOR RH 2019 MY RAV4 RAV4 HV [11/2018 - 02/2019]; PARK ASSIST / MONITORING: BLIND SPOT MONITOR SENSOR: REMOVAL 2019 MY RAV4 RAV4 HV [02/2019 - 10/2019]; PARK ASSIST / MONITORING: BLIND SPOT MONITOR SENSOR: REMOVAL 2020 - 2021 MY RAV4 RAV4 HV [10/2019 - 12/2021]; PARK ASSIST / MONITORING: BLIND SPOT MONITOR SENSOR: REMOVAL 2022 MY RAV4 RAV4 HV [12/2021 - 10/2022]; PARK ASSIST / MONITORING: BLIND SPOT MONITOR SENSOR: REMOVAL 2023 MY RAV4 RAV4 HV [10/2022 - 10/2023]; PARK ASSIST / MONITORING: BLIND SPOT MONITOR SENSOR: REMOVAL 2024 MY RAV4 RAV4 HV [10/2023 -        ]; PARK ASSIST / MONITORING: BLIND SPOT MONITOR SENSOR: REMOVAL

NG

3.

CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR INDICATOR CIRCUIT)

(a) Disconnect the IND2 outer mirror RH (outer rear view mirror indicator RH) connector.

*a

Front view of wire harness connector

(to Blind Spot Monitor Sensor RH)

(b) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Switch Condition

Specified Condition

Q13-4 (OMIR) - Body ground

Ignition switch ON

Below 1 V
OK

REPLACE OUTER MIRROR RH (OUTER REAR VIEW MIRROR INDICATOR RH)

NG

4.

CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR INDICATOR CIRCUIT)

(a) Disconnect the I13*1 or I14*2 outer rear view mirror assembly RH connector.

*1: w/ Foot Light

*2: w/o Foot Light

*a

Front view of wire harness connector

(to Blind Spot Monitor Sensor RH)

(b) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Switch Condition

Specified Condition

Q13-4 (OMIR) - Body ground

Ignition switch ON

Below 1 V
OK

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR