Last Modified: 01-30-2024 |
6.11:8.1.0 |
Doc ID: RM100000001EGZR |
Model Year Start: 2019 |
Model: RAV4 |
Prod Date Range: [11/2018 - 10/2019] |
Title: CELLULAR COMMUNICATION: SAFETY CONNECT SYSTEM: B15C4; Airbag Signal Malfunction/Not Input; 2019 MY RAV4 RAV4 HV [11/2018 - 10/2019] |
DTC
|
B15C4
|
Airbag Signal Malfunction/Not Input
|
DESCRIPTION
If the DCM (Telephone Transceiver Assembly) detects an error in communication between the DCM (Telephone Transceiver Assembly) and the airbag ECU assembly as a result of the DCM (Telephone Transceiver Assembly) self check, this DTC will be set.
DTC No.
|
Detection Item
|
DTC Detection Condition
|
Trouble Area
|
B15C4
|
Airbag Signal Malfunction/Not Input
|
DCM (Telephone Transceiver Assembly) detects an error in signals from airbag ECU assembly when ignition switch is ON.
|
-
Airbag system
-
Harness or connector
-
Airbag ECU assembly
-
DCM (Telephone Transceiver Assembly)
|
WIRING DIAGRAM
CAUTION / NOTICE / HINT
NOTICE:
The vehicle is equipped with an SRS (Supplemental Restraint System) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the Precaution in the SRS.
Click here
PROCEDURE
1.
|
CHECK DTC (AIRBAG SYSTEM)
|
(a) Turn the ignition switch off.
(b) Connect the Techstream to the DLC3.
(c) Turn the ignition switch to ON and wait for 10 seconds.
(d) Turn the Techstream on.
(e) Clear the DTCs.
Click here
Body Electrical > SRS Airbag > Clear DTCs
(f) Recheck for DTCs.
Click here
Body Electrical > SRS Airbag > Trouble Codes
Result
|
Proceed to
|
DTCs are not output
|
A
|
DTCs are output
|
B
|
A
|
|
|
2.
|
CHECK DCM (TELEPHONE TRANSCEIVER ASSEMBLY) (GSW SIGNAL)
|
(a) Remove the DCM (Telephone Transceiver Assembly) but do not disconnect the connectors.
Click here
|
|
*a
|
Component with harness connected
(DCM (Telephone Transceiver Assembly))
|
|
|
(b) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection
|
Switch Condition
|
Specified Condition
|
G9-24 (GSW) - Body ground
|
Ignition switch ON
|
6.5 to 8.5 V
|
Reference Waveform:
Item
|
Condition
|
Tester connection
|
G9-24 (GSW) - Body ground
|
Tool setting
|
5.0 V/DIV., 20 ms/DIV.
|
Vehicle condition
|
Ignition switch ON
|
Result
|
Proceed to
|
8.5 V or higher
|
A
|
Below 6.5 V
|
B
|
6.5 to 8.5 V
|
C
|
A
|
|
|
3.
|
CHECK HARNESS AND CONNECTOR (FOR OPEN CIRCUIT)
|
(a) Remove the airbag ECU assembly but do not disconnect the connectors.
Click here
(b) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection
|
Switch Condition
|
Specified Condition
|
G70-23 (GSW3) - Body ground
|
Ignition switch ON
|
8.5 V or higher
|
Reference Waveform:
Item
|
Condition
|
Tester connection
|
G70-23 (GSW3) - Body ground
|
Tool setting
|
5.0 V/DIV., 20 ms/DIV.
|
Vehicle condition
|
Ignition switch ON
|
|
|
*a
|
Component with harness connected
(Airbag ECU Assembly)
|
|
|
NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR
|
4.
|
CHECK HARNESS AND CONNECTOR (FOR SHORT CIRCUIT)
|
(a) Disconnect the G9 DCM (Telephone Transceiver Assembly) connector.
(b) Disconnect the G70 airbag ECU assembly connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
G9-24 (GSW) - Body ground
|
Always
|
10 kΩ or higher
|
G70-23 (GSW3) - Body ground
|
Always
|
10 kΩ or higher
|
OK
|
|
|
5.
|
REPLACE DCM (TELEPHONE TRANSCEIVER ASSEMBLY)
|
(a) Replace the DCM (Telephone Transceiver Assembly).
Click here
NOTICE:
-
The ignition switch must be off.
-
Do not swap the DCM (Telephone Transceiver Assembly) with one from another vehicle.
6.
|
CHECK HARNESS AND CONNECTOR (DCM (TELEPHONE TRANSCEIVER ASSEMBLY) - AIRBAG ECU ASSEMBLY)
|
(a) Disconnect the G9 DCM (Telephone Transceiver Assembly) connector.
(b) Disconnect the G70 airbag ECU assembly connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
G9-24 (GSW) - G70-23 (GSW3)
|
Always
|
Below 1 Ω
|
G9-24 (GSW) or G70-23 (GSW3) - Body ground
|
Always
|
10 kΩ or higher
|
NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR
|
|