EXTERIOR PANELS / TRIM: REAR DOOR BELT MOULDING: REMOVAL; 2019 MY RAV4 RAV4 HV [11/2018

Last Modified: 01-30-2024	6.11:8.1.0	Doc ID: RM100000001EF6N
Model Year Start: 2019	Model: RAV4	Prod Date Range: [11/2018 - 02/2019]
Title: EXTERIOR PANELS / TRIM: REAR DOOR BELT MOULDING: REMOVAL; 2019 MY RAV4 RAV4 HV [11/2018 - 02/2019]

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear door belt moulding are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced (for HV Model)

Replaced Part or Performed Procedure	Necessary Procedure	Effect/Inoperative Function when Necessary Procedure not Performed
Removal and installation of auxiliary battery terminal	Perform steering sensor zero point calibration	Lane control system
	Perform steering sensor zero point calibration	Pre-collision system
	Memorize steering angle neutral point	Parking assist monitor system
	Memorize steering angle neutral point	Panoramic view monitor system (for HV Model)
	Reset back door close position	Power back door system (for HV Model)
	Back door lock initialization	Power door lock control system
Rear door glass sub-assembly LH Rear door glass sub-assembly RH Rear door glass run LH Rear door glass run RH	Initialize power window control system	Auto up and down function Jam protection function Catch protection function Remote control function Wireless transmitter-linked function Key-linked function Key-off operation function Window open warning function

NOTICE:

After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, be sure to wait for the time specified in the following table before disconnecting the cable from the negative (-) auxiliary battery terminal.

Waiting Time before Disconnecting Cable from Negative (-) Auxiliary Battery Terminal

System Name	See Procedure
Vehicle enrolled in Toyota Entune system or safety connect system	6 minutes
Vehicle not enrolled in Toyota Entune system and safety connect system	1 minute

Necessary Procedure After Parts Removed/Installed/Replaced (for Gasoline Model)

Replaced Part or Performed Procedure	Necessary Procedure	Effect/Inoperative Function when Necessary Procedure not Performed
*: When performing learning using the Techstream. Click here
Removal and installation of auxiliary battery terminal	Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes)	Stop and start system
	Perform steering sensor zero point calibration	Lane control system
		Parking support brake system (for Gasoline Model)*
		Pre-collision system
	Memorize steering angle neutral point	Parking assist monitor system
	Memorize steering angle neutral point	Panoramic view monitor system (for Gasoline Model)
	Reset back door close position	Power back door system (for Gasoline Model)
	Back door lock initialization	Power door lock control system
Rear door glass sub-assembly LH Rear door glass sub-assembly RH Rear door glass run LH Rear door glass run RH	Initialize power window control system	Auto up and down function Jam protection function Catch protection function Remote control function Wireless transmitter-linked function Key-linked function Key-off operation function Window open warning function

NOTICE:

Waiting Time before Disconnecting Cable from Negative (-) Auxiliary Battery Terminal

System Name	See Procedure
Vehicle enrolled in Toyota Entune system or safety connect system	6 minutes
Vehicle not enrolled in Toyota Entune system and safety connect system	1 minute

HINT:

Use the same procedure for the RH and LH sides.
Use the same procedure described for the LH side.
When performing removal for the rear door belt moulding, disconnect the negative (-) auxiliary battery terminal after fully opening the rear door glass.

PROCEDURE

1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click here

2. REMOVE DECK BOARD ASSEMBLY (for HV Model)

Click here

3. REMOVE REAR NO. 2 FLOOR BOARD (for HV Model)

Click here

4. REMOVE BATTERY HOLE COVER (for HV Model)

Click here

5. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

(a) for A25A-FXS:

Click here

(b) for A25A-FKS:

Click here

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click here

6. REMOVE REAR DOOR INSIDE HANDLE BEZEL LH

Click here

7. REMOVE DOOR ASSIST GRIP COVER LH

Click here

8. REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL

Click here

9. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY LH

Click here

10. REMOVE REAR DOOR INNER GLASS WEATHERSTRIP LH

Click here

11. REMOVE REAR DOOR REAR BELT SEAL LH

Click here

12. REMOVE REAR DOOR SERVICE HOLE COVER LH

Click here

13. REMOVE REAR DOOR FRAME GARNISH LH

Click here

14. DISCONNECT REAR DOOR GLASS RUN LH

Click here

15. REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY LH

Click here

16. REMOVE REAR DOOR QUARTER WINDOW GLASS LH

Click here

17. REMOVE REAR DOOR GLASS SUB-ASSEMBLY LH

Click here

18. REMOVE REAR DOOR BELT MOULDING LH

(a) Apply protective tape around the rear door belt moulding LH.

Protective Tape

(b) While pressing the rear door belt moulding LH, pull the edge and detach the claw as shown in the illustration.

	Remove in this Direction (1)
	Remove in this Direction (2)

Remove in this Direction