| Last Modified: 01-30-2024 | 6.11:8.1.0 | Doc ID: RM100000001EF5W |
| Model Year Start: 2019 | Model: RAV4 | Prod Date Range: [11/2018 - 02/2019] |
| Title: EXTERIOR PANELS / TRIM: FRONT BUMPER (for Off Road Package): INSTALLATION; 2019 MY RAV4 RAV4 HV [11/2018 - 02/2019] | ||
INSTALLATION
CAUTION / NOTICE / HINT
HINT:
-
When the front bumper is damaged or deformed due to an accident or contact with other objects, etc., or the bumper installation area on the body is repaired, it is necessary to perform millimeter wave radar sensor adjustment.
Click here
![2019 MY RAV4 RAV4 HV [11/2018 - 02/2019]; CRUISE CONTROL: MILLIMETER WAVE RADAR SENSOR: ADJUSTMENT](/t3Portal/stylegraphics/info.gif)
-
When the front bumper is damaged or deformed due to an accident or contact with other objects, etc., or the bumper installation area on the body is repaired, it is necessary to perform ultrasonic sensor detection angle measurement.
Click here
-
A bolt without a torque specification is shown in the standard bolt chart.
Click here
PROCEDURE
1. INSTALL FRONT BUMPER EXTENSION SUB-ASSEMBLY LH
Click here
2. INSTALL FRONT BUMPER EXTENSION SUB-ASSEMBLY RH
HINT:
Use the same procedure as for the RH and LH sides.
3. INSTALL FRONT BUMPER SEAL (for TMMC Made)
Click here
4. INSTALL FRONT BUMPER LOWER ABSORBER
Click here
5. INSTALL NO. 1 ENGINE UNDER COVER
Click here
6. INSTALL FRONT BUMPER REINFORCEMENT SUB-ASSEMBLY
Click here
7. INSTALL FRONT BUMPER SIDE RETAINER LH
Click here
8. INSTALL FRONT BUMPER SIDE RETAINER RH
HINT:
Use the same procedure described for the LH side.
9. INSTALL FRONT BUMPER NO. 2 ENERGY ABSORBER
(a) Attach the guide and install the front bumper No. 2 energy absorber.
|
Install in this Direction |
10. INSTALL FRONT BUMPER ASSEMBLY
|
(a) Install 2 new clips to the front fender moulding sub-assembly LH. NOTICE: If the front bumper assembly has been removed, replace the clip with a new one. HINT: Use the same procedure as for the RH and LH sides. |
|
(b) Attach the claw to temporarily install the front bumper assembly.
|
|
Install in this Direction |
|
(c) Connect the 2 connectors. |
|
(d) Install the front bumper assembly to the front bumper side retainer LH.
|
(1) Make sure that the front bumper assembly claw contacts the front bumper side retainer LH as shown in the illustration. |
|
(2) Attach the claw to install the front bumper assembly as shown in the illustration.
|
|
Install in this Direction |
HINT:
Use the same procedure as for the RH and LH side.
(3) After installation, if there is a clearance and the front bumper assembly claw can be seen as shown in the illustration, the installation condition is incorrect. Perform the procedure from step 1 again.
|
*a |
Correct |
*b |
Incorrect |
|
(e) Install the 2 clips. HINT: Use the same procedure as for the RH and LH sides. |
|
|
(f) Install the 6 screws. |
|
|
(g) Install the 4 bolts. |
|
(h) Remove the protective tape.
11. INSTALL FRONT FENDER MOULDING SUB-ASSEMBLY LH
(a) Attach the clip and claw to install the front fender moulding sub-assembly LH.
|
|
Install in this Direction |
(b) Remove the protective tape.
(c) Install the screw.
|
Clip |
|
Screw |
(d) Install the 2 clips.
12. INSTALL FRONT FENDER MOULDING SUB-ASSEMBLY RH
HINT:
Use the same procedure as for the LH side.
13. INSTALL FRONT FENDER FRONT SPLASH SHIELD LH
HINT:
Use the same procedure described for the RH side.
(a) for Short Type:
Click here
(b) for Long Type:
Click here
14. INSTALL FRONT FENDER FRONT SPLASH SHIELD RH
HINT:
Use the same procedure as for the LH side.
15. ADJUST FOG LIGHT ASSEMBLY
(a) for LED Type:
Click here
(b) for Bulb Type:
Click here
16. ADJUST FRONT TELEVISION CAMERA ASSEMBLY (w/ Panoramic View Monitor System)
Click here
|
|