Last Modified: 01-30-2024 6.11:8.1.0 Doc ID: RM100000001EEKL
Model Year Start: 2019 Model: RAV4 Prod Date Range: [11/2018 - 10/2019]
Title: STOP AND START: STOP AND START SYSTEM: P30DF62,P30EF4B,P323A00,P323A16,P323AA2,P323B29,P323B38; Backup Boost Converter Circuit Board(Thermistor) Signal Compare Failure; 2019 MY RAV4 [11/2018 - 10/2019]

DTC

P30DF62

Backup Boost Converter Circuit Board(Thermistor) Signal Compare Failure

DTC

P30EF4B

Backup Boost Converter Circuit Board Over Temperature

DTC

P323A00

Backup Boost Converter "A"

DTC

P323A16

Backup Boost Converter "A" Circuit Voltage Below Threshold

DTC

P323AA2

Backup Boost Converter "A" System Voltage Low

DTC

P323B29

Backup Boost Converter "A" Control Circuit Signal Invalid

DTC

P323B38

Backup Boost Converter "A" Control Circuit Signal Cycle Invalid

DESCRIPTION

Refer to DTC P323A19.

Click here 2019 MY RAV4 [11/2018 - 10/2019]; STOP AND START: STOP AND START SYSTEM: P323A19; Backup Boost Converter "A" Circuit Current Above Threshold+

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

Warning Indicate

Memory

Note

P30DF62

Backup Boost Converter Circuit Board(Thermistor) Signal Compare Failure

The following condition is met for 1 second or more (1 trip detection logic):

  • Difference in temperature between thermistor 1 and thermistor 2 of the engine stop and start ECU is 40°C (72°F) or higher.
  • Wire harness or connector
  • Battery
  • BBC NO. 1 fuse
  • BBC NO. 2 fuse
  • Engine stop and start ECU

Blinks

DTC stored

SAE Code: P30DF

P30EF4B

Backup Boost Converter Circuit Board Over Temperature

The following condition is met for 1 second or more (1 trip detection logic):

  • Engine stop and start ECU thermistor temperature is 135°C (275°F) or higher.
  • Wire harness or connector
  • Battery
  • BBC NO. 1 fuse
  • BBC NO. 2 fuse
  • Engine stop and start ECU

Blinks

DTC stored

SAE Code: P30EF

P323A00

Backup Boost Converter "A"

The following condition is met for 1 second or more (1 trip detection logic):

  • Backup boost converter malfunction is detected.
  • Wire harness or connector
  • Battery
  • BBC NO. 1 fuse
  • BBC NO. 2 fuse
  • Engine stop and start ECU

Blinks

DTC stored

SAE Code: P323A

P323A16

Backup Boost Converter "A" Circuit Voltage Below Threshold

One of the following conditions is met for 1 second or more (1 trip detection logic):

  • B41 or IG41 voltage is 6.0 V or less and backup boost converter output overcurrent is not detected.
  • B42 or B43 voltage is 6.0 V or less, backup boost converter is not overheating and backup boost converter output overcurrent is not detected.
  • Wire harness or connector
  • Battery
  • BBC NO. 1 fuse
  • BBC NO. 2 fuse
  • Engine stop and start ECU

Blinks

DTC stored

SAE Code: P323A

P323AA2

Backup Boost Converter "A" System Voltage Low

The following condition is met for 1 second or more (1 trip detection logic):

  • Backup boost converter malfunction is detected.
  • Wire harness or connector
  • Battery
  • BBC NO. 1 fuse
  • BBC NO. 2 fuse
  • Engine stop and start ECU

Blinks

DTC stored

SAE Code: P323A

P323B29

Backup Boost Converter "A" Control Circuit Signal Invalid

The following condition is met for 1 second or more (1 trip detection logic):

  • Backup boost converter malfunction is detected.
  • Wire harness or connector
  • Battery
  • BBC NO. 1 fuse
  • BBC NO. 2 fuse
  • Engine stop and start ECU

Blinks

DTC stored

SAE Code: P323C

P323B38

Backup Boost Converter "A" Control Circuit Signal Cycle Invalid

The following condition is met for 1 second or more (1 trip detection logic):

  • Backup boost converter malfunction is detected.
  • Wire harness or connector
  • Battery
  • BBC NO. 1 fuse
  • BBC NO. 2 fuse
  • Engine stop and start ECU

Blinks

DTC stored

SAE Code: P323C

CONFIRMATION DRIVING PATTERN

HINT:

  • If the cable is disconnected from the battery terminal, stop and start control is prohibited until refresh charge is completed.

    In this case, let the vehicle idle to complete the refresh charge. The refresh charge is complete when the Data List item "Status of Battery Charge Control" changes from "Refresh Charge Mode". (Usually, idling the engine for 5 to 60 minutes with the battery fluid temperature at 11°C (51°F) or higher, the refresh charge will be completed.)

  • If the Techstream is not available and the Data List item "Status of Battery Charge Control" cannot be checked, charge the battery by idling the engine for approximately 5 to 60 minutes or driving the vehicle, and then drive the vehicle and check that stop and start control operates.

    If the engine is started with the hood open, the system determines that a jump start has occurred. Therefore, make sure that the hood is closed before starting the engine and driving the vehicle.

  • After the refresh charge completes, turn the ignition switch off, wait for at least 30 seconds, and then start the engine again. If the vehicle enters refresh charge mode again while the engine is idling, the initial refresh charge did not properly complete, so wait for the refresh charge to complete.
  • Allow the engine to idle for 3 minutes after it is warmed up and check that the engine idle speed is within 50 rpm of the target idle speed.

CONFIRMATION AFTER TROUBLESHOOTING

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(c) Turn the Techstream on.

(d) Clear the DTCs.

Powertrain > Stop and Start > Clear DTCs

(e) Start the engine and warm it up.

(f) Drive the vehicle at 7 km/h (4 mph) or more.

CAUTION:

When performing Confirmation Driving Pattern, obey all speed limits and traffic laws.

(g) Depress the brake pedal and stop the vehicle.

(h) Keep the engine stopped by stop and start control for 1 second or more. (Keep the shift lever in D.)

(i) Release the brake pedal with the shift lever in D to start the engine.

HINT:

If the engine cranks slowly when the engine is restarted, it can be determined that the battery voltage is low.

(j) Check that DTCs are not output.

Powertrain > Stop and Start > Trouble Codes

STOP AND START SYSTEM OPERATION CHECK

HINT:

  • If the cable is disconnected from the battery terminal, stop and start control is prohibited until refresh charge is completed.

    In this case, let the vehicle idle to complete the refresh charge. The refresh charge is complete when the Data List item "Status of Battery Charge Control" changes from "Refresh Charge Mode". (Usually, idling the engine for 5 to 60 minutes with the battery fluid temperature at 11°C (51°F) or higher, the refresh charge will be completed.)

  • If the Techstream is not available and the Data List item "Status of Battery Charge Control" cannot be checked, charge the battery by idling the engine for approximately 5 to 60 minutes or driving the vehicle, and then drive the vehicle and check that stop and start control operates.

    If the engine is started with the hood open, the system determines that a jump start has occurred. Therefore, make sure that the hood is closed before starting the engine and driving the vehicle.

  • After the refresh charge completes, turn the ignition switch off, wait for at least 30 seconds, and then start the engine again. If the vehicle enters refresh charge mode again while the engine is idling, the initial refresh charge did not properly complete, so wait for the refresh charge to complete.

(a) Start the engine and warm it up.

(b) Turn the air conditioning system off.

(c) Drive the vehicle at 7 km/h (4 mph) or more.

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.

(d) Depress the brake pedal and stop the vehicle.

(e) Allow the engine to stop by stop and start control. (Keep the shift lever in D.)

(f) Release the brake pedal with the shift lever in D to start the engine.

WIRING DIAGRAM

Refer to DTC P323A19.

Click here 2019 MY RAV4 [11/2018 - 10/2019]; STOP AND START: STOP AND START SYSTEM: P323A19; Backup Boost Converter "A" Circuit Current Above Threshold+

CAUTION / NOTICE / HINT

NOTICE:

  • Before replacing the engine stop and start ECU, read the number of starter operations and write it into a new engine stop and start ECU.

    Click here 2019 MY RAV4 [11/2018 - 10/2019]; STOP AND START: STOP AND START SYSTEM: REGISTRATION

  • After replacing the engine stop and start ECU or air conditioning amplifier assembly, reset and perform learning of the air conditioning information in the engine stop and start ECU.

    Click here 2019 MY RAV4 [11/2018 - 10/2019]; STOP AND START: STOP AND START SYSTEM: REGISTRATION

  • After replacing the engine stop and start ECU or airbag ECU assembly, clear and calibrate the deceleration sensor zero point in the engine stop and start ECU.

    Click here 2019 MY RAV4 [11/2018 - 10/2019]; STOP AND START: STOP AND START SYSTEM: REGISTRATION

  • When the engine stop and start ECU or oil pump with solenoid assembly is replaced, check the oil pump with solenoid assembly.

    Click here 2019 MY RAV4 [11/2018 - 10/2019]; STOP AND START: STOP AND START SYSTEM: REGISTRATION

  • Inspect the fuses for circuits related to this system before performing the following procedure.

HINT:

  • DTCs for the stop and start system are not cleared even if the malfunction has been repaired. After repairing the malfunction, be sure to clear the DTCs.

    Click here 2019 - 2023 MY RAV4 [11/2018 - 10/2023]; STOP AND START: STOP AND START SYSTEM: DTC CHECK / CLEAR

  • Using the Techstream, read the freeze frame data before troubleshooting. System condition information is recorded as freeze frame data the moment a DTC is stored. This information can be useful when troubleshooting.

    Click here 2019 - 2021 MY RAV4 [11/2018 - 12/2021]; STOP AND START: STOP AND START SYSTEM: FREEZE FRAME DATA

PROCEDURE

1.

CHECK HARNESS AND CONNECTOR (BIN1 AND BIN2 TERMINALS POWER SOURCE CIRCUIT)

*a

Front view of wire harness connector

(to Engine Stop and Start ECU)

(a) Disconnect the engine stop and start ECU connector.

(b) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Condition

Specified Condition

A33-1 (BIN2) - Body ground

Always

9.5 to 14 V

A33-3 (BIN1) - Body ground

Always

9.5 to 14 V

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (ENGINE STOP AND START ECU - BATTERY)

OK

2.

CHECK HARNESS AND CONNECTOR (IG1 TERMINAL POWER SOURCE CIRCUIT)

*a

Front view of wire harness connector

(to Engine Stop and Start ECU)

(a) Disconnect the engine stop and start ECU connector.

(b) Turn the ignition switch to ON.

(c) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Condition

Specified Condition

A32-21 (IG1) - Body ground

Ignition switch ON

9.5 to 14 V

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (ENGINE STOP AND START ECU - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (IG1 NO. 1 RELAY))

OK

3.

CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - BODY GROUND)

(a) Disconnect the engine stop and start ECU connector.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

A34-6 (DGND) - Body ground

Always

Below 1 Ω

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

4.

CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)

(a) Disconnect the engine stop and start ECU connector.

(b) Disconnect the radio and display receiver assembly connector. (w/ Display Audio System)

(c) Disconnect the electrical key and tire pressure monitoring system receiver assembly connector. (w/ Tire Pressure Warning System)

(d) Disconnect the central gateway ECU (network gateway ECU) connector.

(e) Disconnect the millimeter wave radar sensor assembly connector. (w/ Dynamic Radar Cruise Control System)

(f) Disconnect the blind spot monitor sensor LH connector.

(g) Disconnect the blind spot monitor sensor RH connector.

(h) Disconnect the air conditioning control assembly connector.

(i) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

A32-12 (B42) - G3-4 (+B1)*1

Always

Below 1 Ω

A32-2 (B41) - M8-7 (+B)*2

Always

Below 1 Ω

A32-3 (IG41) - M8-1 (IG)*2

Always

Below 1 Ω

A32-3 (IG41) - G72-11 (IG1)

Always

Below 1 Ω

A32-3 (IG41) - B9-8 (IGB)*3

Always

Below 1 Ω

A32-3 (IG41) - Q1-5 (BLB)

Always

Below 1 Ω

A32-3 (IG41) - Q13-5 (BRB)

Always

Below 1 Ω

A32-3 (IG41) - G24-9 (IG+)

Always

Below 1 Ω

A32-12 (B42) or G3-4 (+B1)*1 - Body ground and other terminals

Always

10 kΩ or higher

A32-2 (B41) or M8-7 (+B)*2 - Body ground and other terminals

Always

10 kΩ or higher

A32-3 (IG41) or M8-1 (IG)*2 - Body ground and other terminals

Always

10 kΩ or higher

A32-3 (IG41) or G72-11 (IG1) - Body ground and other terminals

Always

10 kΩ or higher

A32-3 (IG41) or B9-8 (IGB)*3 - Body ground and other terminals

Always

10 kΩ or higher

A32-3 (IG41) or Q1-5 (BLB) - Body ground and other terminals

Always

10 kΩ or higher

A32-3 (IG41) or Q13-5 (BRB) - Body ground and other terminals

Always

10 kΩ or higher

A32-3 (IG41) or G24-9 (IG+) - Body ground and other terminals

Always

10 kΩ or higher

  • *1: w/ Display Audio System
  • *2: w/ Tire Pressure Warning System
  • *3: w/ Dynamic Radar Cruise Control System
OK

REPLACE ENGINE STOP AND START ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR