| Last Modified: 01-30-2024 | 6.11:8.1.0 | Doc ID: RM100000001EDVO |
| Model Year Start: 2019 | Model: RAV4 | Prod Date Range: [11/2018 - 02/2019] |
| Title: SUPPLEMENTAL RESTRAINT SYSTEMS: SRS SEAT CUSHION AIRBAG ASSEMBLY: REMOVAL; 2019 MY RAV4 RAV4 HV [11/2018 - 02/2019] | ||
REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during front seat cushion airbag assembly removal/installation are shown below.
Necessary Procedures After Parts Removed/Installed/Replaced
|
Replaced Part or Performed Procedure |
Necessary Procedure |
Effect/Inoperative Function when Necessary Procedure not Performed |
Link |
|---|---|---|---|
|
*: When performing learning using the Techstream.
Click here
|
|||
|
Disconnect cable from negative (-) auxiliary battery terminal |
Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) |
Stop and start system |
|
|
Perform steering sensor zero point calibration |
Lane control system |
|
|
|
Parking support brake system (for Gasoline model)* |
|||
|
Pre-collision system |
|||
|
Memorize steering angle neutral point |
Parking assist monitor system |
|
|
|
Panoramic view monitor system (for Gasoline model) |
|
||
|
Reset back door close position |
Power back door system (for Gasoline model) |
|
|
|
Back door lock initialization |
Power door lock control system |
|
|
NOTICE:
After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, be sure to wait for the time specified in the following table before disconnecting the cable from the negative (-) auxiliary battery terminal.
Waiting Time before Disconnecting Cable from Negative (-) Auxiliary Battery Terminal
|
System Name |
See Procedure |
|---|---|
|
Vehicle enrolled in Toyota Entune system or safety connect system |
6 minutes |
|
Vehicle not enrolled in Toyota Entune system and safety connect system |
1 minute |
PROCEDURE
1. PRECAUTION
CAUTION:
-
Be sure to read precaution thoroughly before servicing.
Click here
![2019 MY RAV4 RAV4 HV [11/2018 - 02/2019]; SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM (w/ Occupant Classification System): PRECAUTION](/t3Portal/stylegraphics/info.gif)
-
Wear protective gloves. Sharp areas on the parts may injure your hands.
- There is risk of injury.
NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click here
2. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL
Click here
CAUTION:
- Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
- If the airbag deploys for any reason, it may cause a serious accident.
NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click here
3. REMOVE FRONT SEAT ASSEMBLY RH
HINT:
Use the same procedure described for the LH side.
Click here
4. REMOVE RECLINING HINGE COVER RH
HINT:
Use the same procedure described for the LH side.
Click here
5. REMOVE RECLINING ADJUSTER RELEASE HANDLE RH
HINT:
Use the same procedure described for the LH side.
Click here
6. REMOVE FRONT SEAT CUSHION SHIELD RH
Click here
7. REMOVE FRONT SEAT INNER CUSHION SHIELD RH
Click here
8. REMOVE SEPARATE TYPE FRONT SEATBACK ASSEMBLY RH
HINT:
Use the same procedure described for the LH side.
Click here
9. REMOVE SEPARATE TYPE FRONT SEAT CUSHION COVER WITH PAD
HINT:
Use the same procedure described for the LH side.
Click here
10. REMOVE FRONT SEAT CUSHION AIRBAG ASSEMBLY RH
CAUTION:
- When storing the front seat cushion airbag assembly RH, keep the airbag deployment side facing upward.
- If the airbag deploys for any reason, it may cause a serious accident.
|
Deployment Side |
|
(a) Detach the 2 wire harness clamps. |
|
(b) Detach the claw and disconnect the airbag connector.
(c) Remove the 2 nuts and front seat cushion airbag assembly RH.
CAUTION:
- Do not reuse the nut.
- If the installation surface or surrounding area of the front seat cushion airbag assembly RH is deformed or damaged, replace the front seat adjuster assembly RH with a new one.
|
Remove in this Direction |
|
|