Last Modified: 01-30-2024 6.11:8.1.0 Doc ID: RM100000001ECE4
Model Year Start: 2019 Model: RAV4 Prod Date Range: [11/2018 - 02/2019]
Title: REAR SUSPENSION: REAR SHOCK ABSORBER: INSTALLATION; 2019 MY RAV4 RAV4 HV [11/2018 - 02/2019]

INSTALLATION

CAUTION / NOTICE / HINT

HINT:

  • Use the same procedure for the RH side and LH side.
  • The following procedure is for the LH side.

PROCEDURE

1. INSTALL REAR SUSPENSION SUPPORT ASSEMBLY

(a) Secure the rear suspension support assembly in a vise using aluminum plates.

NOTICE:

Do not overtighten the vise.

(b) Install the rear suspension support assembly to the rear shock absorber assembly.

(c) Apply a few drops of adhesive to the threads of a new rear support to rear shock absorber nut.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

(d) Using SST and a 6 mm hexagon socket wrench, hold the rear shock absorber rod and tighten the rear support to rear shock absorber nut.

SST: 09729-97202

Torque:

Specified tightening torque :

25 N·m {255 kgf·cm, 18 ft·lbf}

NOTICE:

Securely insert the 6 mm hexagon socket wrench into the rear shock absorber rod to prevent damage to the rear shock absorber assembly when tightening the rear support to rear shock absorber nut.

HINT:

  • Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

    Click here 2019 - 2024 MY RAV4 RAV4 HV [11/2018 -        ]; INTRODUCTION: REPAIR INSTRUCTION: PRECAUTION

  • When using SST (fulcrum length of 40 mm (1.57 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)):

    21 N*m (214 kgf*cm, 15 ft.*lbf)

*a

Torque Wrench Fulcrum Length

2. INSTALL REAR SHOCK ABSORBER CAP

(a) Install the rear shock absorber cap to the rear shock absorber assembly.

3. TEMPORARILY INSTALL REAR SHOCK ABSORBER ASSEMBLY

(a) Temporarily install the rear shock absorber assembly to the rear axle carrier sub-assembly with the nut and plate washer.

NOTICE:

Hold the rear axle carrier pin while rotating the nut.

*1

Rear Axle Carrier Pin

4. STABILIZE SUSPENSION

(a) Using a jack and wooden block, apply load to the suspension so that the rear No. 2 suspension arm assembly is positioned as shown in the illustration.

Standard Length (A):

13 mm (0.512 in.)

CAUTION:

Do not jack up the rear No. 2 suspension arm assembly too high as the vehicle may fall.

NOTICE:

  • When jacking up the rear No. 2 suspension arm assembly, be sure to jack it up slowly.
  • Make sure to perform this operation with the vehicle kept as low as possible.

*a

Wooden Block

*b

Jack

Wooden Block Placement Location

5. INSTALL REAR UPPER CONTROL ARM ASSEMBLY

(a) Install the rear upper control arm assembly to the rear axle carrier sub-assembly with the bolt and nut.

Torque:

73 N·m {744 kgf·cm, 54 ft·lbf}

NOTICE:

  • Insert the bolt with the threaded end facing the rear of the vehicle.
  • Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured.

6. CONNECT REAR SHOCK ABSORBER ASSEMBLY

(a) Connect the rear shock absorber assembly to the vehicle with the 2 bolts.

Torque:

55 N·m {561 kgf·cm, 41 ft·lbf}

NOTICE:

Temporarily tighten the bolt (A) and then fully tighten the 2 bolts in the order of (B) and (A).

7. INSTALL REAR SHOCK ABSORBER ASSEMBLY

(a) Using a ball joint lock nut wrench, fully tighten the rear shock absorber assembly with the nut.

Torque:

Specified tightening torque :

125 N·m {1275 kgf·cm, 92 ft·lbf}

NOTICE:

Hold the rear axle carrier pin while rotating the nut.

HINT:

  • Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

    Click here 2019 - 2024 MY RAV4 RAV4 HV [11/2018 -        ]; INTRODUCTION: REPAIR INSTRUCTION: PRECAUTION

  • When using a ball joint lock nut wrench (fulcrum length of 149.75 mm (5.90 in.)) + torque wrench (fulcrum length of 400 mm (1.31 ft.)):

    91 N*m (928 kgf*cm, 67 ft.*lbf)

*1

Rear Axle Carrier Pin

*a

Torque Wrench Fulcrum Length

*b

Ball Joint Lock Nut Wrench

*c

Turn

*d

Hold

8. INSTALL REAR STABILIZER LINK ASSEMBLY

Click here 2019 - 2024 MY RAV4 RAV4 HV [11/2018 -        ]; REAR SUSPENSION: REAR STABILIZER BAR: INSTALLATION+

9. INSTALL LOWER NO. 2 CONTROL ARM COVER (w/ Cover)

Click here 2019 MY RAV4 RAV4 HV [11/2018 - 02/2019]; REAR SUSPENSION: REAR LOWER ARM: INSTALLATION+

10. INSTALL REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH (w/ Height Control Sensor)

(a) for LH Side:

Click here 2019 MY RAV4 RAV4 HV [11/2018 - 02/2019]; LIGHTING (EXT): HEIGHT CONTROL SENSOR: INSTALLATION

11. INSTALL REAR WHEEL

Click here 2019 - 2024 MY RAV4 RAV4 HV [11/2018 -        ]; MAINTENANCE: TIRE AND WHEEL: INSTALLATION

12. INSPECT AND ADJUST REAR WHEEL ALIGNMENT

Click here 2019 - 2020 MY RAV4 RAV4 HV [11/2018 - 08/2020]; ALIGNMENT / HANDLING DIAGNOSIS: REAR WHEEL ALIGNMENT: ADJUSTMENT

13. PERFORM INITIALIZATION

Click here 2019 MY RAV4 RAV4 HV [11/2018 - 02/2019]; INTRODUCTION: REPAIR INSTRUCTION: INITIALIZATION